SOURCE: Reset Check engine light on 1993 Geo Tracker
A 1993 Tracker will have OBD1 technology. Just unplug the battery for 5minutes and plug it back in. If the light persists You will have to find out and repair the problem that your cars computer believes it has.
SOURCE: 1993 geo tracker fuel injector
ecm does control but is also based on input from the Throttle position senser. unplug the TPS and try again. Also make sure the ECM and engine grounds are good
SOURCE: need torque setting for 1993 geo tracker front
i1m sorry to say that wheel bearings are not set to a torque specification, when you have repacked the bearings [ inner and outer ] ,reassembled it ,take the nut up until thewheel starts to drag and not turn very far when you try to spin it spin it backward and forward several times,grab the top of the wheel and try to push it in and out,if you getany movement at all tighten the nut a couple of castilations. do it all over again, spinthe wheel a few times and then try for the crossways movement again, if there is no movement ,you are very close to being right....................now comes the experience bit , iwould take it one more castilation of the nut because i know the feel that is need ed,,without that i suggest you put the pin in where you ereput the cap on and go for a 5 minute drive . whenyou get back ,jack it up and thespinning of the wheel again and try for the top crossways movement ,if there is any tighten thenut 2 castilations, and provided that when you try to spin the wheel by hand with a reasonably strong push the wheel should trael about 6 inches at least after your hand leaves it ,it is now a close as you are going to get itput it all to gether and for the next day or so put yor hand on the grease cap after you have driven anydistance, and you will feel it is warm but you should be able tohold your hand on the grease cap. there you have it ,any questions come back."youdoit"
SOURCE: HOW DO YOU REMOVE THE RADIO FROM A 1995 GEO TRACKER????????
To remove the radio:
Remove the ashtray by raising the armrest cover and removing the two
screws at the rear of the ashtray. Slide the ashtray back and then lift
it out. Be careful of the two front tabs, as you don't want to break
them.
Reach below the wood console, where the ashtray front tabs were inserted. Loosen and remove the two wing nuts.
With a small, long flat bladed screwdriver, pry out the leather shifter
surround. The leather shifter surround has a center chrome retaining
ring, the leather surround, and then finally a black plastic surround.
The chrome retaining ring has 3-4 tabs which are locked in below the
leather surround. It depends on the year of the Jaguar. Probably the 95
has three, but maybe four. They should be at the front and rear of the
trim piece (2 front and 1 back, or 2 front and two back) but I've seen
then on the sides. The point is, you have to be careful with the
screwdriver and find the tabs. The screwdriver should be slid between
the leather and the retainer. Pull upwards on the retainer gently, and
as you loosen the tabs, it will come out.
Remove the leather surround. Once the chrome retainer has been removed, it should be easy to work it out of the console.
Loosen the black trim ring gently as it has tabs as well, but they are
visible once the leather trim has been removed. Lift it upwards out of
the wood trim and pull it to the side out of the way. You don't need to
disconnect the wires, just lay the black trim to the side.
Lift the rear of the wood console trim and gently, gently slide it back
and up. It will try to hang on the leather console, and can be
difficult. Patience is important, as the walnut on the ski slope cracks
easy (really easy).
Once the wood console trim (ski slope) is removed, you should have a
row of screws up the side of the center control panel, where the radio
and AC controls are. There are four to six on each side, depending on
what Jaguar used at the time, as the 95 cars mechanically are somewhat
of a blend of the XJ40 and the XJ300. Remove these screws, and note any
spacers that were behind them. These spacers get lost quickly, and
cause the ski slope to sit awkwardly on the console.
The radio will slide forwards once these screws are removed. Remove the
radio harness and the antenna lead. As the books say, assembly is
reverse of removal.
Good luck, and let me know if you have questions. If you are replacing
the radio, let me know as I have the harness wiring codes and can help
you with that as well.
SOURCE: How do u replace 1993 geo tracker ignition switch
remove steering wheel covers
remove lock
remove screw holding ignition switch
78 views
Usually answered in minutes!
which engine.? 8v or 16valves.
here ill toss coin land on 16http://fixkick.com/sensors/93-mpi-smog1....
if 8v
its here toohttp://fixkick.com/find-parts.html
its fun (not) to see the fixya brain
try to guess answers wrong every time.
what joke that is.
×