Use a noid light or other tool for checking the injector pulse is present.
If injectors have a pulse when the engine is cranked the reason there is no spray is there is no fuel pressure - fuse, relay, pump, wiring, pipework, filter. Water in the fuel tank is also a possibility.
If there is no pulse it could be crank or cam sensor, fuse, wiring or even the ECU.
-Use noise light to check each injector wire connector to see
If there is power there or not when you crank.
-If there is not power at all then 90% the cam & crank sensor are effect.
Good luck
Mai
SOURCE: 98 chevy s10 blazer turn signal
Unplug the turn signal relay from the fuse box and start you engine. Does it still make that noise?
If yes... Put the relay back in, that is not the problem.
If No...Then the relay could be bad, replace it!
PLEASE RATE THIS SOLUTION! Thank You Very Much!
SOURCE: 2000 Chevy Blazer Cranks but wont start...
What about the fuel filter????? Have you changed it out??? If you can spary something like a started fluid, that means it is a fuel problem. My last check, it has to be above 50-psi on the fuel pressure to make it run right. I had 35psi, but whould not get over 30mph or down hill maybe 45mph. Check both filter & pressure, but check pressure with a New fule filter!!!!
SOURCE: My 4.3 vortec engine in my s10 blazer won't start
try the ignition module. if it is bad it does not send the signal for the the throttle body injectors to spray feul.
SOURCE: injectors s10 1991
So your saying fuel pump giving you pressure but ALL injectors are not firing. IF ALL INJECTORS ARE NOT FIRING AND FUEL PUMP IS A-OK THEN ECU IS THE PROBLEM.
However, if a few are not firing then its probably those injectors.
SOURCE: diagram on how to remove
Here is the removal procedure, and the procedure is the same for both the V-6 and the V-8 Vortec engines. Also, be certain to put engine oil on the "o"-ring seal for the fuel injector assembly before installing the upper intake. Let me know if you require any further assistance.
REMOVAL:
1. Disconnect the battery negative cable assembly from the battery negative terminal.
2. Remove the air cleaner assembly.
3. Remove the wiring harness connectors and the brackets and move aside.
4. Remove the throttle cable and the bracket from the upper intake manifold.
5. Remove the cruise control cable, (if equipped).
6. Remove the fuel lines from the intake to the rear of the block.
7. Remove the ignition coil and the bracket.
8. Remove the upper intake manifold.
INSTALLATION:
1. Install the upper intake manifold gasket.
2. Install the upper intake manifold. Use care not to pinch the injector lines between the upper and lower intake manifolds.
3. Install the upper intake manifold bolts. Note the marks made at disassembly for proper stud location. Install the two corner studs first in order to help align the two halves. NOTE: Other than the two torque passes listed below, the OE Manufacturer did NOT address or supply a bolt tightening sequence for the upper Intake Manifold for this model year, or other model years where this 2 piece manifold setup is used. A "Play It Safe" final tightening sequence would be to tighten from the center most bolts to the outer most bolts.
4. Tighten the bolts in two steps: a. Tighten the bolts on the first sequence to 5 Nm (44 inch lbs.). b. Tighten the bolts on the final sequence to 10 Nm (88 inch lbs.).
5. Install the purge solenoid and bracket.
6. Install the ignition coil and bracket.
7. Install the PCV hose et the upper intake manifold.
8. Install the fuel lines from the intake at the rear of the block.
9. Install the cruise control cable (if equipped).
10. Install the throttle cable and bracket from the upper intake manifold.
11. Install the wiring harness connectors and brackets.
12. Install the air cleaner assembly.
13. Connect the battery negative cable assembly to the battery negative terminal. - Tighten the bolt to 15 Nm (11 ft. lbs.).
509 views
Usually answered in minutes!
Replaced fuel pump, fuel relay fuses are good starts with starting fluid also has fuel to tbi power to injectors cranks but wont start
×