Question about 2004 Hyundai Tiburon

Open Question

2004 hyundi tiburon one low beam nothing else

Posted by on

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

paul proctor

  • 4102 Answers

SOURCE: misfire at low revs

Hi, this could be down to the fuel line and injectors being dirty as at low revs their is less pressure forcing the fuel through.
My first thing to try would be to buy a fuel cleaner that you pour into the fuel tank these tend to solve the problem your having.
Make sure you buy the correct one ie petrol or diesel follow instructions on the bottle for amounts to use then run the car for a good run usually takes about 4 hours of driving time to fully clear all fuel lines and filters.
I use this in my car once a month as you can pick up small traces of dirt from filling stations this then clogs up over time.
Hopefully this will solve your problem if not then give me a shout back and ill assist you further

Posted on Aug 05, 2009

Ad

super_guy

  • 1986 Answers

SOURCE: HOW DO I ADJUST THE LOW BEAM HEADLIGHTS TO SHINE

The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.

Posted on Oct 06, 2009

Anonymous

  • 205 Answers

SOURCE: axel removal on 2004 hyundi santa fe

http://www.autozone.com/autozone/repairinfo/repairguide/repairGuideContent.jsp?partName=Drive+Train&pageId=0900c152801a5958&partId=0900c152801a5958
Here is a link to autozone.com that has step by step instructions a diagrams for that

Posted on Oct 17, 2009

teemossinmia

T Moss

  • 265 Answers

SOURCE: Which is the high beam which is the low beam

The low beam is always on the outside, and the high beam is always closer to the grill...

Posted on Dec 04, 2009

Chris Sibley

  • 54 Answers

SOURCE: low bean headlights don't work

Check fuse box in engine bay (should be near battery) inside should be the fuse for high beam and low beam.

Posted on Sep 18, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i change low beam headlight on 1996 hyundi excell


Take bulb out from inside engine compartment and change bulb. See your user manual.

Jul 21, 2014 | 1996 Hyundai Accent

1 Answer

2001 tiburon


if equipt with a control module may need to get a new one..try your fuseable links off the battery also..

Dec 08, 2013 | Cars & Trucks

1 Answer

2004 envoy xuv low beams dont work switched fuses 45 and 46 still nothing any ideas


Other possibilities are; the bulbs themselves, burnt or corroded bulb sockets, or a bad headlight selector switch.

Dec 11, 2011 | 2004 GMC Envoy

1 Answer

Is there more than one relay switch? I found one for the high beams but not one for the low beams. I changed my dimmer switch and the bulbs but nothing has helped, I have high beams just not low beams and...


The low beam relay is #46 in the underhood fuse panel. check its contact pins before replacing it. If they are corroded, try cleaning them first.

Nov 28, 2010 | 2004 GMC Envoy

2 Answers

Low bean headlights don't work but high beam does on 2004 Hyundai Tiburon. How do you know what the problem is.


Check fuse box in engine bay (should be near battery) inside should be the fuse for high beam and low beam.

Aug 24, 2010 | 2004 Hyundai Tiburon

1 Answer

Both low beam lights went out... hi beams are ok. is there a seperate fuse for the low beams?


there are seperate fuses however did you check the bulbs. they could just need replacing. there will be fuses for left and right. should be under the hood.

Dec 24, 2009 | 2004 Hyundai Tiburon

2 Answers

Which is the high beam which is the low beam on a 2003 Hyundai Tiburon?


The low beam is always on the outside, and the high beam is always closer to the grill...

Dec 04, 2009 | 2003 Hyundai Tiburon

1 Answer

HOW DO I ADJUST THE LOW BEAM HEADLIGHTS TO SHINE


The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.

Oct 06, 2009 | 2001 Hyundai Tiburon

1 Answer

Adjusting headlights on my 2004 ford taurs


The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.

Oct 04, 2009 | 2004 Ford Taurus

1 Answer

Changing the headlights


This picture shows the rear side of the headlamp assembly. I've circled the access caps to the high & low beam bulbs (they just twist off (counter-clockwise) to access the bulbs. Depending on which engine is in your Tiburon, access is easier if you remove three 10mm mounting bolts to the headlamp assemblies and remove the entire headlamp assemblies (see illustration)
c173c7f.jpg You'll want to disconnect these two connectors .. then remember to reconnect them when you put the assemblies back on.

Hope this helps

Dec 20, 2008 | 2004 Hyundai Tiburon

Not finding what you are looking for?
2004 Hyundai Tiburon Logo

Related Topics:

49 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

Marvin
Marvin

Level 3 Expert

85219 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...