Question about 2000 Acura TL

Open Question

Were is the mass flow sensor located on my 2000 acura tl

Posted by on

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Anonymous

  • 4 Answers

SOURCE: trying to replace a front headlight bulb on 2001 acura 3.2 TL

Look for the end of the wire retainer clip. Unhook it and lift it up. Remember not to touch the bulb. But if you do, just clean it with a bit of alcohol.

btw - Here's a bit of info from a previous post of mine...
The low beams consist of three parts. The bulb, inverter/ballast and the ignitor. The bulbs usually start to loose their color long before they burn out. The inverters/ballasts either go out after a while or take a while to start up.

Before you spend money on a new bulb, try swapping it with the one on the other side. You'll need a security torx screwdriver to get the covers off of the back of the lights. Don't touch the glass bulbs. If you do, just clean them with a bit of alcohol.

If the problem stays on that side, try swapping the ignitors. They're mounted inside the black covers.

If the problem is still on that side you've got a bad inverter. They're mounted on the bottom of the headlight assembly. You'll need to remove the front bumper and remove the headlight assembly to get to it. (I recommend you take pictures as you remove things so can put them back together correctly.)

Posted on Jan 05, 2009

Ad

Anonymous

  • 41 Answers

SOURCE: starter replacement on acura 2000 TL 3.2

This starter can be changed without disassembling the top of the engine on the 2.5 with automatic transmission. You will need a 10mm, 14 mm, 17mm, and a 9mm wrench. First with any electrical repair disconnect the battery at the negative terminal. The starter is on the driver's side close to the firewall below the intake manifold. Remove the transmission dip stick so you don't ruin it, then look and study the starter itself. You will notice the starter drive housing with a top and bottom bolt. The top bolt is a 14mm and the bottom a 17mm, loosen both a half turn. Remove the top 14mm bolt first, then the bottom 17mm, this will allow you to pull the starter out of the bell housing. With some angling and no brackets holding the back of the starter you should be able to pull it out enough to disconnect the positive wire and 9mm nut from the soleniod. Disconnect the starter ignition small wire by pulling it off it's connector. Now just pull it out of the engine and fender void and you've got it, saving about a hundred and fifty dollars of labor. Take it to the parts house and match it up with a well made remanufactured or new starter. Reverse the proceedure, hook up the battery.

Posted on Mar 19, 2009

Roger Foster

  • 701 Answers

SOURCE: firing order

Hello bailsdenied: THe fireing order for a Acura NSX 3.2L DOHC (vtec) engine is 1-4-2-5-3-6. If this is the correct model of car then it is right. If this is not the right car then ask and I will send the correct one. Please rate the answer you recieve as this lets us nkow you were provided the correct answer to your question. Thank you for using FixYa. Roger55224f4.jpg

Posted on Apr 25, 2009

emissionwiz

Marvin

  • 85222 Answers

SOURCE: 2005 Acura TL Fuel Filter

the fuel filter for this is in the gas tank, it is part of the fuel pump module.

Posted on May 22, 2009

badbrains

  • 60 Answers

SOURCE: where is plug in acura 2000 tl for check engine

The OBDII connector is located in the center console just behind the ashtray. There is a plastic cover that must be removed and you will find the connector behind the cover.

Posted on Jan 31, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the fuse box Acura 3.2 TL 2000?


On this website you find fuse box diagram and description for Acura TL (2000)

Acura TL 2000 wiring diagrams fuse panel CARKNOWLEDGE

Sep 14, 2012 | 2000 Acura TL

1 Answer

My 96 Acura TL is hesitating to take off what is wrong with it?


it could be a sign of fuel pump going bad. It could also be a sensor problem like the Mass Air Flow sensor which regulates air pressure to fuel so you get proper combustion.

Mar 10, 2011 | Acura TL Cars & Trucks

1 Answer

On 1996 Acura tl 2.5 where is located the speed sensor?


For 1996 Acura TL 2.5L PFI 5cyl the Vehicle Speed Sensor - Location is located mounted on transmission.


zjlimited_595.jpg


Fig.: Exploded view of the vehicle speed sensor (click for zoom).



Hope this helps (remember to rate this answer).

Feb 01, 2011 | 1996 Acura TL Series

2 Answers

Location of mass air flow sensor, 2000 Grand Prix GTP


Hi:
The mass air flow sensor is a round sensor that is mounted in the air intake, between the air cleaner box and the engine throttle body.

Feb 07, 2010 | 2000 Pontiac Grand Prix

2 Answers

Where is plug in acura 2000 tl for check engine


The OBDII connector is located in the center console just behind the ashtray. There is a plastic cover that must be removed and you will find the connector behind the cover.

Jan 31, 2010 | 2000 Acura TL

2 Answers

High fuel consumption. only 200 miles per tank


it has gotta be the o2 sensor, map sensor, or the mass air flow meter.............. these are the main inputs to the computer that controls the fuel control....let me know how that works out please

Dec 08, 2009 | 2004 Acura MDX

1 Answer

2004 tl hard start problem? taking 2 or 3 times of turning the key to start


check fuel pressure and the fuel pressure regulator. if you have an intake clean the mass air flow sensor

Nov 06, 2009 | 2004 Acura TL

2 Answers

I have 2006 Acura TL V6. How do I change the cabin air filter?


To change cabin air filter on Acura TL firs time you need to open the glove box and then remove the arm that holds the glovebox. Press the 2 sides of the glovebox to take this out like in picture bellow.
acura-tl-2004-2010-cabin-air-filter-location.jpgAcura TL 2004-2010 cabin air filter location
After do this you can see and locate the cabin air filter housing cover.
acura-tl-2004-2010-cabin-air-filter-housing-cover.jpgAcura TL 2004-2010 cabin air filter housing cover
Push the 2 tabs from the filter frame to unhooking from the housing cover. Take the frame out and replace the old cabin air filter with the new one with the air flow indicating arrow pointing down.

acura-tl-2004-2010-reinstal-the-air-cabin-filter.jpgAcura TL 2004-2010 reinstal the air cabin filter

Nov 26, 2008 | 2006 Honda Accord

Not finding what you are looking for?
2000 Acura TL Logo

Related Topics:

115 people viewed this question

Ask a Question

Usually answered in minutes!

Top Acura Experts

Marvin
Marvin

Level 3 Expert

85222 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Are you an Acura Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...