Question about 1998 Pontiac Bonneville

Open Question

What size socket to remove harmonic balancer 1998 pontaic binville

Posted by on

Ad

3 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Anonymous

  • 1 Answer

SOURCE: screw location on dash for 1998 pontaic grand am

Its 2 screws in the middle below the temp controls and 2 just above the speedometer.

Posted on Sep 04, 2008

Ad

mcjake2003

  • 1 Answer

SOURCE: How do you get the harmonic balancer

I didn't have to take off the balancer I just needed to jack the motor up higher and the motor mount came out the top. Thanks Jake

Posted on Dec 09, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to install balance drive gear on crankshaft 2007 Camry 2.4


Remove old crankshaft pulley ( Harmonic Balancer), by putting sturdy socket,think its 19mm, or 3/4 " on the center crankshaft bolt, with a good size breaker bar, wedge the breaker bar in between the suspension, and drive axle, to keep the breaker bar from spinning, while, you now turn the key inside the car, to engage starter, to spin the crankshaft,which may take several attempts, of turning the key, and putting socket back on, they are very stubborn,to break the center bolt loose,
Then remove harmonic balancer, with a PULLER, which requires 2 bolts, in the threaded holes, one on each side of the now empty center bolt hole, autozone , advance, has these to loan out, only requires deposit, which they give back to you, when you return it.
Put square key in slot on bare crankshaft, slide harmonic balancer,(crankshaft pulley,while lining up the square key,and tighten crankshaft bolt.

Oct 24, 2014 | 2007 Toyota Camry

1 Answer

Harmonic balancer seal-1997 plymouth grand voyager van


Depending on the amount of room to the radiator / fan shroud it is not excessively difficult to do if you have the correct tools. You will need a 1/2 inch impact gun , harmonic balancer remover, screw driver, hammer. a piece of pipe the same size as the outside dia of the seal and a hammer along with a selection of spanners and sockets to remove the fan belt and anything else that will be in your way.. IF the balance is held on with a bolt then the easiest thing is the impact gun. the harmonic puller to pull the balancer off with, the pipe and the hammer to replace the seal. the screw driver to pry out the old seal

Dec 22, 2013 | Cars & Trucks

1 Answer

Harmonic balancer came apart while driving how do i fix


by 2nd hand one fit the right socket on the front of the pulley flik your ignition for 1 second to se the rotesion of the engine and go with the socket the opposite site you need force 150-200 punds to unlock it.

Aug 08, 2012 | 1998 Honda Civic

2 Answers

How do you remove the Harmonic Balancer for a 1998 plymouth voyager


the best thing to use is called a chain wrench -- for a cheap one to buy, try harbor freight if available, or perhaps your local parts store has a tool borrowing program.
Best regards
Ck

Sep 11, 2011 | 1998 Plymouth Voyager

1 Answer

How do i remove harmonic balancer & replace


YOU NEED A HARMONIC BALANCER PULLER TOOL AND A 15M SIX POINT SOCKET TO REMOVE HARMONIC BALANCER BOLT.TURN OFF RADIO AND REMOVE THE DRIVE BELT AND REMOVE THE NEGATIVE BATTERY CABLE. REMOVE THE STARTER SO YOU CAN PUT A LARGE SCREW DRIVER OR LARGE PUNCH TO STICK IN ONE OF THE FLY WHEEL HOLES TO KEEP ENGINE FROM TURNING WHEN YOU LOOSEN THE HARMONIC BALANCE BOLT. ALSO SCREW DRIVER AND PUNCH CAN KEEP ENGINE FROM TURNING WHEN REMOVER THE HARMONIC BALANCER. YOU WILL NEED A HELPER TO HOLD PUNCH OR SCREW DRIVER WHILE YOU LOOSEN THE BOLT. YOU CAN GO TO SEARS OR ANY AUTO PARTS STORE AND BUY HARMONIC BALANCER PULLER.TORQUE HARMONIC BALANCER BOLT TO 76 FT LBS.

Apr 23, 2011 | 2003 Pontiac Montana

1 Answer

Need bolt size to remove a harmonic balancer from a ford sport trac


Most fords are 15/16 inch. butyou didnt state the engine size. Youll also need a harmonic balancer puller and most parts stores can rent you one some times for no charge ( just pay for it and bring it back all together and you'll get all or most of your money back). with the balancer off you'll need to ut it or a new one back on You need a harmonic balancer installer to put it on as beating it back onewith a hammer will damage the balancer and the crank and even the whole engine. If you don't want todo all of this just take it to a mechanic that doesthis work all the time ad hasthe correct tools to do itright. Yes you can beat it off and back on but you'll likly do exensive damage. ( not always). If you don't have the right sized sockets andthe power impac to remove the bolt you had best just hire the job done as this is not a do it youself job unless your a regular ( work all day every day) mechanic.

Nov 06, 2010 | 2004 Ford Explorer Sport Trac

1 Answer

I just brought a 94 buick park ave.. And wantd to know how to remove and install an harmonic balancer..


You will need to remove the radiator and if equipped the fan housing. Remove the belts. You may need to remove the fan itself if you haven't already done so. You'll need a large breaker bar with a properly sized socket to remove the retaining bolt from the harmonic balancer. Once that is removed you will need to use a special tool you can borrow or rent from Auto Zone or O'Reilleys auto parts store to remove the harmonic balancer itself. I recommend you get the Haynes repair manual on this vehicle before you start as I assume you are doing some type of engine work requiring the removal of the balancer and this manual will assist you in doing that work.

Jun 19, 2010 | Cars & Trucks

1 Answer

How do i remove the old harmonic balancer on a 1994 honda accord lx


First, look at the direction the balancer turns. Remove the belts. Put the proper sized socket on the balancer bolt and, install a breaker bar into the socket. Make sure the bar is at the side of the engine compartment, where the top of the balancer rotates toward. Next, BUMP THE KEY but DO NOT crank the engine. When the bar contacts the wall or other object, it will stop, allowing the engine to continue and break the bolt loose.

Oct 13, 2009 | 1994 Honda Accord

2 Answers

BAD HARMONIC BALANCER


this site is lame ,i just called a dealership and got the answers i needed,i got no help here

Nov 25, 2008 | 1998 Nissan Pathfinder

Not finding what you are looking for?
1998 Pontiac Bonneville Logo

Related Topics:

39 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

Marvin
Marvin

Level 3 Expert

85206 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...