Question about 1998 Subaru Forester

Open Question

1998 subaru forester camshaft instalation procedure.

Posted by on

Ad

6 Suggested Answers

Anonymous

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

frankster016

  • 314 Answers

SOURCE: 1998 Subaru forester repair manual, Non-existent?

Yes, all the colour codes will be the same, plus 99.9% of the rest! Frankster016

Posted on Nov 24, 2008

Ad
keemo68

Ronald Mueller

  • 1263 Answers

SOURCE: Where is th fuel pump relay on the 1998 subaru

thew fuel pump relay will be located in the power distribution box under the hood it is a square fuse like device either black or grey in color

Posted on Apr 20, 2009

Richard Scordino

  • 6982 Answers

SOURCE: 1998 subaru forester runs rough when it rains.

Check the cap and rotor for internal carbon tracking or, just change them. Also, take a look at the coil when its dark and rainy and see if there is any arcing where the coil wire goes into it.

Posted on Jun 19, 2009

Anonymous

  • 119 Answers

SOURCE: Procedure for replacing rear wheel bearings 2000 Forester

i'm assuming you don't have a hubshark,this is a tool that will alllow you to remove the bearing while the knuckle is attached to the car,you may be able to rent this tool at a auto prts store .if not you need to remove the entie knuckle,first remove the trailing arm bolt,then the lateral link bolt{long and stubborn bolt},disassemble the brake shoes and parking brake cable,abs sensor if equipped the knuckle to strut bolt{no marking necessary they are not eccentric} then you need a to use or borrow a press to remove hub and bearings good luck

Posted on Jul 26, 2009

super_guy

  • 1986 Answers

SOURCE: Installing replacement side mirror on 2007 Subaru Forester

yes... you'll need to remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then you can access the bolts holding the mirror on and disconnect the wiring harness as well..

Posted on Aug 20, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to change timing belt on 1998subaru forester


That's a long procedure. Your best bet is to buy a repair manual at your local parts store. All brands have the timing belt procedure in them.

Sep 07, 2014 | 1998 Subaru Forester

1 Answer

Instructions for replacing headlight bulb for '98 subaru forester.


Open the hood, reach behind the headlight assembly and carefully turn the lamp assembly counter-clockwise, then remove the pigtail. To install a new lamp, simply do the reverse procedure.

Jan 09, 2011 | 1998 Subaru Forester

1 Answer

AWD went out in my 1998 Subaru Forester?


This recently happened to my 98 Subaru Legacy Outback.
My problem is in the rear differential. May be the same for you.
When making a turn, the car sounds like a Star Wars T.I.E. Fighter. The outside wheel is not turning fast enough to keep up with the inside wheel or vice versa. AWD is disengaged and car is currently operating on Front WD. I was told this is fine to drive this way.

Jul 22, 2010 | 1998 Subaru Forester

1 Answer

1998 subaru forester; the fan motor sounds like


you probly have a leaf stuck in your air box

Mar 09, 2010 | 1998 Subaru Forester

1 Answer

My 1998 Engine EJ20J hasitates, can ECU be reprogrammed or do i have to change it to higher version?


Hello,I had the same problem with my 1998 2.0 Forester,I tried a lot options:
(other spark plugs,new sparkplugcables,other ignition coil,replacing the knocksensor,another camshaft sensor,reset the ECU on a Subaru select monitor,"it doesn work with an universal scantool" using ron98 petrol instead of ron95),but no satisfiing result.
At least i bougt on E-Bay a new ECU ,an 22611AD311 in stead of the AD310,
The AD311 has an software update and now the engine runs smoother and the hasitation is practically gone.
But you can trie a reset first,you can also do it yourself,
Disconnect the both batteryclams set the ignitionswiths on with the key and push the brake for 5 seconds.Then connect the battery and try.
Good luck with it

Arnold

Sep 21, 2009 | 1998 Subaru Forester

1 Answer

Window stuck - 1998 Forester Limited


I installed speakers in my door panels.
Pop up the window controlls unplug switches,
remove plastic screw hiders to expose phillips screws
remove screw from door latch lever
pull out on door panel, then lift up
its not too hard good luck
lowrob77@yahoo.com

Jan 10, 2009 | 1998 Subaru Forester

2 Answers

Removing Camshaft pulley on 2.5 Dohc forester motor


To replace the timing belt back guard you will have to remove both pulleys.There is a small bolt under each pulley holding the belt guard Use a large socket to hold the pulley while you break the bolt loose with a 17mm socket. I have just done this while replacing my head gaskets due to coolant boiling from the gasket leak.

Dec 15, 2008 | 1998 Subaru Forester

3 Answers

1998 Subaru forester repair manual, Non-existent?


Yes, all the colour codes will be the same, plus 99.9% of the rest! Frankster016

Oct 28, 2008 | 1998 Subaru Forester

Not finding what you are looking for?
1998 Subaru Forester Logo

Related Topics:

21 people viewed this question

Ask a Question

Usually answered in minutes!

Top Subaru Experts

Marvin
Marvin

Level 3 Expert

85223 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Subaru Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...