Question about 1992 Ford Ranger

Open Question

Locate 92 ford ranger 2.3 cam sensor

Need to replace the cam sensor on a 92 Ford Ranger. Have not been able to locate it. looks like the wires i have for the used one is 1 green/with pink strip, & 1 yellow, with black stripe. Have not been able to trace the wires down nor sensor. Any pictures would be greatly appreciated?

Posted by on

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
Ajkill

Anand Kumar

  • 2035 Answers

SOURCE: 2003 Ford Ranger/2.3 O2 sensor - How many and Where located ???

Engine Heated oxygen and catalyst monitor sensors—2.3L engine44e2701.jpg

Posted on Jan 16, 2009

Ad

Anonymous

  • 22 Answers

SOURCE: need location of the erg sensor 2000 ford ranger

The egr valve has two sensors. One is an EGR position sensor which is physically attached to the EGR valve. The other sensor is the DPFE (Delta Pressure Feedback EGR) sensor, commonly called the EGR pressure sensor. It's location varies depending on the engine you have. You can fine this sensor by following the vacuum hose on the EGR valve. It will be with in inches of the EGR valve. The sensor will be black (plastic) or silver (metal), have two or three vacuum ports and an electrical connection on it.

The vacuum pressure sensor is a high failure item on fords. Any Ford parts department will have one in stock, as well as some aftermarket parts stores.

The new sensor may not look exactly the same as the old part, but will have all the hook ups as the old one. You may also need to replace the vacuum hose to the sensor as well

Posted on Feb 25, 2009

Anonymous

  • 22 Answers

SOURCE: location of the egr sensor on 2000 ford ranger

The EGR pressure sensor is located within inches of the EGR valve. The exact location varies depending on the engine (2.5L, 3.0L or 4.0L). It is usually attached to the upper intake manifold with two small bolts.

Posted on Feb 27, 2009

localwonder

Michael Masters

  • 6784 Answers

SOURCE: most common cause for code P0340 of 95 Ranger

Hi, the cam shaft sensor will be located Under the hood, center, upper engine area, mounted behind rear of intake manifold, in the engine block.


This is a magnetic or hall effect sensor. It sends a signal to the computer relaying information about shaft speed, position and acceleration or deceleration. This information determines when the fuel/air mixture needs to be ignited and how much mixture is needed for the engine.

The possible causes of failure will be faulty housing or faulty wires as well. A faulty ECM could trigger a false alarm as well. this is highly unlikely but, possible in most cases. The most reported reasons is flat out sensor failure.

Posted on May 21, 2009

Molson02536

Harvey N Tawatao

  • 3854 Answers

SOURCE: installing chip and want to double check wiring. Need to find IAT/MAF sensor diagram for 2003 Ford Ranger

Save your money, the chip is a ohm resistor at Radio Shack for under $2.00. It splices in to you IAT wire harness located at the intake tube between the air filter housing and throttle body.
Problem with this system is, that you can not adjust anything and have to run a constant 91 octane just to make sure you do not have a Detonation. The ECM will catch the Detonation from the knock sensor and compensate for it by retarding the timing which in turn lose of HP till next start up.
If you like and don't mind the check engine light on once and awhile, you can do the same by just disconnecting the IAT wire harness which give the ECM a 0 resistance thinking it's -20 out side and turn the timing up and lengths the injector pules.
When i was running a Nitro in the Toy before i sold it, i had installed a 10K ohm Potentiometer which you can buy at radio shack for under $5.00 i believe, I just spliced it in to the IAC wire harness so if i wanted to play with the Nitro I'ld turn the resistor up making the engine think it's 185 degrees F and would ****** the timing so i would not hurt the engine. But if i wanted to get more timing i would just turn the knob to drop the resistance to get more time since the engine thinks it's -20 out side.
Hope this helps. Keep me posted if you need more info. Best thing is to do a dyno tune and you can change everything right down to the Shift points.

Posted on May 29, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I am in need of under dash fuse panel diagrams backside power side 92 Ford ranger xlt.


Confused by 'backside power side', but

Just Google

92 Ford Ranger XLT fuse box
And look at the Inage tab.

Or if you are after wiring details

92 Ford Ranger XLT wiring schematic

Jan 26, 2016 | Ford Cars & Trucks

1 Answer

Where is the cam sensor located on my 98 ford ranger.


It is located where the distributor would normally be.
cam-sensor-located-98-ford-ranger-nxmumukqemthcsnheggjjug3-4-0.gif

Oct 17, 2015 | Ford Cars & Trucks

1 Answer

Show me wire diagram for 92 ford ranger battrey termials


Red cable goes to the + terminal of the battery. The black cable goes to the - termonal of the battery.

Feb 08, 2015 | 1992 Ford Ranger

2 Answers

Where is the cam shaft senser on a ford ranger 2.5 td 2002


Ford did not put a 2.5 in a Ranger, maybe a 2.3 ?
2.3 = 2007-01-27_154722_2.gif
3.0 - The CMP sensor& synchronizer/shaft are located behind the intake manifold (i.e., back near the firewall on a Ranger) on the top of the cylinder block. If you just need to replace the sensor, it is a simple job of unplugging the electrical connector and removing the screws holding the sensor in place. Here is a sketch of the sensor to give you an idea what to look for:

Jun 17, 2014 | 2002 Ford Ranger Regular Cab

1 Answer

My 92 ford ranger doesn't fire on cyl. 3 and 4


Hi the very first thing which comes to my mind is why are the adjacent cylinders loosing compression, could it be a bad head gasket? let me know how you make out?

Jun 19, 2012 | 1992 Ford Ranger

1 Answer

Need to fix a camshaft position sensor on an 01 ford ranger 3.0


the cam sensor is located in the topside of the engine, behind the manifold, near the firewall. it is held in by two mounting bolts. just remove the wire connector and the two mounting bolts. you can then remove the cam sensor. slightly lube the oring on the new cam sensor and reinstall. tighten two mounting bolts and reconnect the wire connector

Mar 25, 2010 | 2001 Ford Ranger Regular Cab

1 Answer

Timing Marks-99 Ford Ranger


Its Dot to Dot.. Crank Pointer Up.. CAm Pointer down.. DOT 2 DOT.. Thank you

Mar 15, 2009 | 1999 Ford Ranger SuperCab

Not finding what you are looking for?
1992 Ford Ranger Logo

Related Topics:

387 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

Marvin
Marvin

Level 3 Expert

85222 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

gerry bissi

Level 3 Expert

4388 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...