2008 Mazda Tribute Logo

Related Topics:

Regina Gordon Posted on Mar 20, 2017

2008 Mazda tribute got hit left front bumper fender grill and hood on impact car shut off won't come out of park won't turn over lites radio horn and alarm all turn on just won't turn over help

5 Related Answers

Anonymous

  • 14 Answers
  • Posted on Aug 20, 2009

SOURCE: Loud whining noise on left turn (Mazda Tribute 04)

sounds like a wheel bearing maybe faulty from your text it sounds like it could be the osf you could try jacking vehicle up with engine off handbrake applied and in neutral spin the wheel and see if it makes noise or wiggle it to see if it has any play possibly take off greade cap and see if any grease in bearing /

Ad

Anonymous

  • 5081 Answers
  • Posted on Oct 09, 2009

SOURCE: how do u replace the right front turn signal lamp

This is actually a little tricky, open the hood, there will be a single screw holding the turn signal lamp in place take that off, here's the tricky part, take two flathead screw drivers and place them on either side of the turn signal housing pry it back and forth a little bit, it should begin to slide out directy in front of the car, it has tracks kind of like a dresser drawer, when you done replacing the light, just slide it back in and tighten the screw .

alicantecoli

Colin Stickland

  • 22516 Answers
  • Posted on Dec 23, 2009

SOURCE: 2001 Mazda tribute 4wd es driverside front wheel noise?

iam am no doubt totally wrong here ,but i would first of all check the power steering fluid level ,then turn steering from left to right with engine running and check the fluid level again

Anonymous

  • 617 Answers
  • Posted on Feb 07, 2010

SOURCE: I have an 02 Mazda Tribute with a leaking Radiator

1. Drain coolant
2 Remove lower splash shields
3. Disconnect the lower radiator hose and the high pressure transaxle line
4. Lower the vehicle
5. Disconnect the transaxle return line
6. Disconnect the upper radiator hose and degas hose
7. Position the hood latch assembly out of the way
8. remove the 2 bolts and the center support
9 remove the 2 top bolts retaining the cooling fan to the radiator
10. remove the upper radiator support brackets, and remove the radiator from the vehicle
11. To install, reverse the removal procedure

crash76

Jerry

  • 185 Answers
  • Posted on Jan 25, 2011

SOURCE: steering column lock and won`t unlock

Here you got some tip: http://car-tech.org.uk/tips/how-to-fix-a-locked-steering-wheel/ If this will not work and you live in or near London then call them, I am sure they can fix it.

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1helpful
1answer

How to remove a L/Front fender on a 1996 Mazda 626

Fenders are bolt on. Remove the plastic inner wheel well. Rais the hood. Remove bolts along too, in door jamb and inner wheel well. Most vehicles also require removing the front bumper cover, headlight assembly and sometimes the grill. You should be able to see the bolt hole locations on the replacement fender. Once you install it do not tighten up the bolts. You'll need to align the fender til the hood to get a narrow consistent seam then tighten the bolts.
0helpful
1answer

Detailed instructions on front bumper removal. NOTE: From all the videos, it appears the CAB is different than the sedan. An example is the grill does NOT come up with the hood.

Remove wheels. Remove fender liners front. Remove three nuts per side from inside fender wells. Remove fog lamp grilles. Remove vertical bolt just inside grilles--pointing up. Remove two screws per side under hood near front of fender. Put milk crate under front bumper. Remove belly pan first. Slide bumper forward onto milk crate, disconnect headlight washer line at quick disconnect if so equipped. Disconnect fog light connectors. Remove bumper.
0helpful
2answers
0helpful
1answer

How do you remove the front bumper of a Mercedes Benz cl65 amg

Lift the front end of the car and support on stands.
Remove the front wheels.
Remove the fowards under-tray.
Remove the forward halves of the front wheel arch liners.
Unscrew the small down-facing Torx screw at each top rear corner of the bumper.
Gently pry inwards the rear end of the U-shaped steel channel that holds the fender and bumper flanges together.
Pull the channel rearwards to disengage the lugs from the diagonal slots at the forward end, and remove the channels.
Disconnect the external air temp sensor in the bottom left air intake.
Disconnect the parking sensors connector at the right rear corner. You need to open the lever lock and pull hard without damaging the wiring.
Open the hood and remove two bolts on top of the bumper, next to the inner headlamp mountings.
Remove two nuts in lower grille - vertically beneath above bolts.
If its your first time, get a friend and pull the bumper forwards very slowly and gently, avoiding scratching the fenders.
The bumper is surprisingly light.

It will take about an hour.
0helpful
1answer

When I pull the hood release, the hood doesn't pop up. I either have to have a second person lift slightly on the hood while I pull the release, or I have to wedge something under the edge of the hood...

No the bumpers don't do that. After time it seems the latch itself bends. Look at it and see where it is hitting. There is some adjustment in the catch at the bottom/grill. But I usually just bend the latch left or right as needed. You can use a pry bar to bend it or just hit it with a hammer. Be careful not to hit the hood.
0helpful
1answer

How do you change the front parking light bulb on a 2008 toyota tacoma

if you can not access or see the bulb under the hood in the corner at the fender or inside of fender you will have to remove the headlight assembly and all car makers are making changing bulbs a pain. if you do have to remove the headlight assembly then the steps per repair manual are to remove the grille,bumper cover,bumper filler.believe me there are a lot of customers that wonder why us technicians have to charge so much just to put a bulb in but we did not design the car and it is crazy what you see now days.........good luck and i hope this will help and if i can give any more details let me know......the bulb will twist to remove when you get to it.........let me know how you come out with the project.......
0helpful
2answers
2helpful
2answers

How to replace a front headlight bulb on a 2008 Mazda 3

for the most part you open the hood and turn the socket and the bulb come out if you have an autozone near you they will install it if you get the bulb from them and thats about any auto parts store
2helpful
2answers

Horn does not work ,I can't locate it under the hood,where is it

Try looking behind the grill around the headlights. If you don't see it there look under neath and up just behind the bumper.
11helpful
2answers

How to change the whole headlight assembly on a 05 Honda CRV

You have to remove the front bumper and grill etc

There are 5 bolts holding the headlight assembly in place. 2 at the top and 3 underneath.

Remove the plastic cross piece by prising out the clips and then the grille clips too then unbolt the bolts eithr side under the wheel arch. The bumper is still fastened using cips. Pull the bumper forward to unclip.
Not finding what you are looking for?

55 views

Ask a Question

Usually answered in minutes!

Top Mazda Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6988 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...