I need wiring diagram for a 1999 Ford f250 side view power mirror. I am installing 2003 telescoping side view mirrors and the color code in different.

Haynes manuals will have the information they run around $30.00 any auto part store.Good Luck.

Installing 08 mirrors on 01 Superduty, looking for wiring diagrams ...

www.ford-trucks.com > ... > Super Duty & Heavy Duty

Aug 12, 2008 - Installing 08 mirrors on 01 Superduty, looking for wiring diagrams Super Duty ... 2013-2014 mirror plug pin outs, SUPERDUTY_08, Super Duty ... Power/Heated/Lighted Tow Mirror upgrade...
Jul 24, 2012
F250 Paddle to towing mirror installation
Dec 20, 2010
Towing Mirror Wiring Harness Adaptor
Sep 15, 2010
Towing mirrors
Apr 16, 2010
More results from www.ford-trucks.com

here's 1996, all I have. Please rate.

Mirror, Power — Outside Rear View NOTE: This procedure applies to both RH and LH power outside rear view mirrors.

Removal

1. Remove the front door trim panel (23942). Refer to Section 01-05 for the removal procedure.
   

1. Remove the two outside rear view mirror inside mounting hole cover screws and the outside rear view mirror mounting hole cover (17K709) from the front door (20124).
   
   
   
   
   

1. Remove the wire clip.
   

1. Disconnect the power outside rear view mirror electrical connector.
   
   
   
   
   

1. Remove the three power outside rear view mirror bolts and the power outside rear view mirror.
   
   
   
   
   

Installation
To install, reverse the removal procedure. Tighten the three power outside rear view mirror bolts to 3-4 Nm (27-35 lb-in). Glass, Outside Mirror
Removal and Installation
Refer to the glass replacement procedures in Manual Mirror for power outside rear view mirror glass (17K707) Trim Cover
Removal

1. Remove the front door trim panel. Refer to Section 01-05 for the removal procedure.
   

1. Remove the two outside rear view mirror inside mounting hole cover screws.
   
   
   Remove the outside rear view mirror mounting hole cover.

Installation
To install, reverse the removal procedure. Mirror Control
Removal

1. Use a small flat-blade screwdriver to pry the power outside rear view mirror control switch from the instrument panel (04320).
   
   
   

The door panel must be removed to get to the wiring. On a 04 250 you need to: pop off the moulding covering the mirror mounting nuts. Pry the window switch plate forward then up to disconnect it, then unplug it . Rmove the screw behind the switch plate and behind the reflector. Push up on the door panel to remove it.

take the door panel off there is 2 to 3 bolts holding it on

Im Not Sure About The Disasembling Part But The Led Lights Are A Single Unit To Fix The Bulbs That Are Out you Will Have To Change The Whole Light Assembly in Most Cases

Mirror — Outside Rear View Removal
NOTE: Do not remove the exterior mirror assembly when repairing an individual part. Individual components can be installed without removing the exterior mirror.

1. Disconnect the battery ground cable (14301).

1. Remove the front door trim panel; refer to Section 501-05.

1. Remove the speaker.
   1. Remove the screws.
   1. Disconnect the electrical connector.
   1. Remove the speaker.

1. Remove the outside rear view mirror (17682).
   1. Disconnect the power mirror wiring clips.
   1. Remove the outside rear view mirror nuts.
   1. Remove the outside rear view mirror.
      • Feed the power mirror wiring through the opening in the front door (20124).

Installation

1. NOTE: When the battery (10655) is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 mi) or more to relearn the strategy.
   To install, reverse the removal procedure.

Colors will be the same on both ends ( the switch and the mirrors . Unfortunately both left and right mirrors have the same wiring colors. Check electical flow through the mirror switch so as to know which wire controls left mirror and which wire controls right mirror, to insure you don't re-wire in error . Hope this helps

are you trting to tighten the mirror glass or the mirror where it attaches to the body? I don't think glass is removable in 99. Only can try to press on glass to seat if unseated. not too hard.

1. Remove the front door trim panel; refer to Section 501-05 .
2. go to car-part.com for a used mirror. Page with * is cheapest seller.

1. Remove the speaker.
   1. Remove the screws.
   1. Disconnect the electrical connector.
   1. Remove the speaker.

1. Remove the outside rear view mirror (17682).
   1. Disconnect the power mirror wiring clips.
   1. Remove the outside rear view mirror nuts.
   1. Remove the outside rear view mirror.
      • Feed the power mirror wiring through the opening in the front door (20124).

------------------------------------------------------

----------------------------
SECTION 501-09: Rear View Mirrors 2001 Explorer/Mountaineer Workshop Manual
REMOVAL AND INSTALLATION Exterior Mirror Glass, 2001 model Removal
NOTE: Exterior mirror glass is serviceable only on vehicles built after July of 2001.
NOTE: Passenger side exterior mirror shown, driver side exterior mirror similar.
All mirrors

1. Position the glass in the full up position.

1. Locate the notch at the bottom of the exterior mirror glass.

1. Release the exterior mirror glass.
   1. Insert a long flat-bladed screwdriver in the notch.
   1. Push the screwdriver into the notch until the glass is released.

Heated mirrors

1. Position aside the exterior mirror glass.

1. Disconnect the electrical connectors.

All mirrors

1. Remove the exterior mirror glass (17K707) passenger side or (17T675) driver side.

Installation
Heated mirrors

1. Connect the electrical connectors.

All mirrors

1. Position the exterior mirror glass on the exterior mirror motor.

1. Place a hand against the back of the exterior mirror housing and a hand flat against the exterior mirror glass. Press the glass in place until fully seated.

First, after receiving an email from FixYa about my "Ford 1992 Ranger Problem" which was not my query at all, as the question was titled "F150 and F250 Mirror Compatibility" , I am asked for money for the answer. Then they ask me what the solution is, so they can sell it to some one else. Why would I pay someone when they can't even get the question right.
Incidentally, the solution was to ask someone competent.