Torque settings or 2006 Ford ranger ...for head, main bearings, connecting rod bearing, flywheel and valve clearance

https://www.google.com/search?q=Ford+Courier+F8+motor+torque+settings

Torque setting for Ford Courier F8 motor from main bearing

Fixya https://www.fixya.com > Forum > Cars & Trucks > Ford
10 hours ago - Main Bearings Torque specs. 40-43 Ft. Lbs. Cylinder Head Torque specs. 56-60 Ft. Lbs. Read full answer. Oct 05, 2009 • ...

What are the torque settings for a 1997 ford courier 2.2

JustAnswer https://www.justanswer.com > Australian Car Repair
Jul 1, 2021 - Tighten special flywheel-to-crankshaft bolts to 73-87 Nm (54-64 ft. lbs.). 35.If equipped, install clutch disc and clutch pressure plate and ...

1 answer · Top answer: TORQUE SPECIFICATIONS Connecting Rod [https://my.alldata.com/repair/#/repair/vehicle/26150/component ...

1.8 ford courier 8valve torque settings on cylinder head

Fixya https://www.fixya.com > ... > Ford > Expedition
Sep 4, 2008 - First torque value is 58 ft lbs.....then final torgue is 72 ft lbs. Posted on Mar 21, 2009. 0.

Torque Settings

Kiwi Cylinder Heads Ltd https://www.cylinderheads.co.nz > torque-settings
Cylinder Head Torque Settings.

Torque Specifcations

MAHLE Aftermarket https://www.mahle-aftermarket.com > torque3
Make. Liter CID. Engine Model Year. Rod Torque. Main Torque. Cylinder Head Bolt Torque. ACURA. 1.6. 97. D16A1. 86-89. 23 FT/LBS. 40 FT/LBS. 22, 47 FT/LBS.
124 pages
..

Here is the cylinder hear torque search query. Change for each part and press Enter.

https://www.google.com/search?q=2005+ford+ranger+2.5+cylinder+head+bolt+torque+settings

https://www.google.com/search?q=2005+ford+ranger+2.5+main+bearing+bolt+torque+settings

https://www.google.com/search?q=2005+ford+ranger+2.5+con+rod+bearing+bolt+torque+settings

or the manual

https://barringtondieselclub.co.za/ford/ford-ranger-2.5-he-4-cyl-engine.html

..

Details are here

https://www.justanswer.com/ford/ab7rz-2006-ford-taurus-3-0l-rod-main-bearing-cap-bolt-torque.html

https://www.google.com/search?q=2006+Ford+Taurus+engine+torque+settings

..

I need all the specs of Isuzu npr 4hg1 engine.Cylinder head bolts torque, crankshaft bolts torque, connecting rod caps bolts torque
.

i have a 2009 would these settings also work

TORQUE SPEC FOR ROD BEARING BOLTS 19 - 24 FT LBS TORQUE SPEC FOR MAIN BEARING BOLTS 60 - 70 FT LBS, CRANKSHAFT PULLEY BOLT 85 - 100 FT LBS. MAIN BEARING OIL CLEARANCE .0005 - .0022 CONNECTING ROD OIL CLEARANCE .0008 - .0015 / SHAFT END PLAY .004 - .008 / AND ROD SIDE CLEARANCE IS .004 - .011 HOPE THIS HELP THIS INFORMATION I GAVE YOU IS INLINE 6 -200 AND INLINE 6 - 250 ENGINES

Torque Settings Mains = 108NM
Big Ends = 54NM + 90° +90°
Flywheel = 122.5NM
Cylinder Head = 78 NM + 90° + 90°

Valve Settings
Exhaust = 0.40 mm - 0.50 mm
Intake = 0.20 - 0.3 0mm

General Specifications Item Specification
Displacement L (CID) 4.6 (281)
Number of Cylinders 8
Bore and Stroke mm 90.2 x 90.0
Firing Order 1-3-7-2-6-5-4-8
Oil Pressure (HOT @ 1500 rpm) kPa 138-310
Drive Belt Tension a
Cylinder Head and Valve Train
Combustion Chamber Volume cm 52?±.5
Valve Seats Width?€"Intake mm 1.9-2.1
Valve Seats Width?€"Exhaust mm 1.9-2.1
Valve Seats Angle 44.51-45.01 degrees
Valve Seats Runout (T.I.R.) Max mm 0.025
Valve Arrangement (Front-to-Rear) (Left Hand) E-I-E-I-E-I-E-I
(Right Hand)
I-E-I-E-I-E-I-E
Valve Stem to Guide Clearance?€"Intake mm (Inch) 0.020-0.069
(0.00078-0.00272)
Valve Stem to Guide Clearance?€"Exhaust mm (Inch) 0.045-0.095 (0.0018-0.0037)
Valve Head Diameter?€"Intake mm (Inch) 44.5- (1.75)
Valve Head Diameter?€"Exhaust mm (Inch) 34.0 (1.34)
Valve Head Diameter?€"Gauge Diameters mm (Inch) 42.5- and 32.0
(1.67 and 1.26)
Valve Face Runout Limit mm (Inch) 0.05 (0.002)
Valve Face Angle 45.25-45.75 degrees
Valve Stem Diameter (STD)
?€"Intake mm (Inch) 6.995-6.975 (0.275-0.2746)
Valve Stem Diameter (Std)
?€"Exhaust mm (Inch) 6.970-6.949 (0.274-0.2736)
Valve Springs?€"
Compression Pressure N @
Spec. Length?€"Intake 587.14 N @ 28.02 mm
Valve Springs?€"
Compression Pressure N @
Spec. Length?€"Exhaust 587.14 N @
28.02 mm
Valve Springs?€"Free
Length ( Approximate)?€"
Intake mm (Inch) 49.55 (1.951)
Valve Springs?€"Free
Length (Approximate)?€"
Exhaust mm (Inch) 49.55 (1.951)
Valve Springs?€"Installed
Pressure N @ Spec. Length
?€"Intake 244.64 N @ 40.0 mm
Valve Spring?€"Installed
Pressure N @ Spec. Length
?€"Exhaust 244.64 N @ 40.0 mm
Valve Springs?€"Installed
Pressure N @ Spec. Length
?€"Service Limit 10 % Pressure Less @ 28.02 mm
Valve Springs?€"Installed
Pressure N @ Spec. Length
?€"Out of Square Limit 2 degrees
Valve Guide Inner
Diameter mm (Inch) 7.015-7.044 (0.2761-0.2773)
Rocker Arm?€"Ratio 1.75:1
Valve Tappet?€"Diameter
(STD) mm (Inch) 16.000-15.988 (0.66-0.629)
Valve Tappet?€"Clearance
to Bore mm (Inch) 0.018-0.069
(0.00071-0.00272)
Valve Tappet?€"Service
Limit mm (Inch) 0.016 (0.00063)
Valve Tappet?€"Hydraulic
Leakdown Rate b 5-25 seconds
Valve Tappet?€"Collapsed
Valve Tappet Gap?€"
Desired mm (Inch) 0.085-0.45 (0.0033-0.0177)
Camshaft
Lobe Lift?€"Intake
mm (Inch) 6.58939 (0.2594)
Lobe Lift?€"Exhaust
mm (Inch) 6.58939 (0.2594)
Lobe Lift?€"Allowable
Lobe Lift Loss mm (Inch) 0 (0)
Theoretical Valve Lift @
Zero Lash?€"Intake
mm (Inch) 12.0 (0.472)
Theoretical Valve Lift @
Zero Lash?€"Exhaust
mm (Inch) 12.0 (0.472)
End Play mm (Inch) 0.025-0.165
(0.00098-0.0065)
Journal to Bearing
Clearance mm (Inch) 0.025-0.076
(0.00098-0.003
Journal to Bearing
Clearance?€"Service Limit
mm (Inch) 0.021 (0.0048)
Journal Diameter (All)
mm (Inch) 26.962-26.936
(1.061-1.060)
Journal Diameter (All)?€"
Bearing Inside Diameter
(All) mm (Inch) 27.012-26.987
(1.063-1.0625)
Camshaft Runout
mm (Inch) 0.05 (0.002)
Cylinder Bore
Diameter?€"Surface Finish
(RMS) 0.2-0.6 Microns
Diameter?€"Out-of-Round
Limit mm (Inch) 0.015 (0.0006)
Diameter?€"Out-of-Round
Service Limit mm (Inch) 0.020 (0.00079)
Diameter?€"Taper Service
Limit mm (Inch) 0.006 (0.00023)
Piston
Piston?€"Diameter?€"
Coded Red 1 mm (Inch) 90.177-90.197
(3.550-3.551)
Piston?€"Diameter?€"
Coded Blue 2 mm (Inch) 90.190-90.210
(3.5507-3.5515)
Piston?€"Diameter?€"
Coded Yellow 3 mm (Inch) 90.203-90.223
(3.513-3.5521)
Piston-to-Bore-Clearance
mm (Inch) -0.015 + 0.031 (0.0005-0.0012)
Pin Bore Diameter
mm (Inch) 22.0015-22.004
(0.866-0.8663)
Ring Groove Width?€"
Compression (Top)
mm (Inch) 1.520-1.550 (0.06-0.610)
Ring Groove Width?€"
Compression (Bottom)
mm (Inch) 1.520-1.530 (0.060-0.0602)
Ring Groove Width?€"Oil
Ring mm (Inch) 6.996-7.224 (0.275-0.2844)
Piston Pin?€"Length
mm (Inch) 61.93-62.05 (2.44-2.443)
Diameter mm (Inch) 21.994-21.999
(0.866-0.8661)
Pin to Piston Clearance
mm (Inch) 0.005-0.010
(0.0002-0.0004)
Pin to Rod Clearance
mm (Inch) 0.015-0.040
(0.0006-0.00157)
Piston Rings?€"Ring Gap
?€"Compression (Top)
mm (Inch) 1.0 MAX (0.0394)
Piston Rings?€"Ring Gap
?€"Compression (Top)
mm (Inch) 1.0 MAX (0.0394)
Oil Ring?€"Side Clearance
mm (Inch) 1.25 MAX (0.05)
Oil Ring?€"Compression
(Top) mm (Inch) 0.040-0.090
(0.0016-0.0031)
Oil Ring?€"Compression
(Top) mm (Inch) 0.030-0.080
(0.0012-0.00031)
Oil Ring Snug Fit
Oil Ring?€"Service Limit
mm (Inch) 0.015 MAX (0.0006)
Ring Gap?€"Compression
(Top) mm (Inch) 0.23-0.49
(0.01-0.02)
Ring Gap?€"Compression
(Bottom) mm (Inch) 0.23-0.49
(0.01-0.02)
Ring Gap?€"Oil Ring (Steel
Rail) mm (Inch) 0.05-0.66 (0.006-0.026)
Lubrication System
Oil Capacity?€"Automatic
Transmission (Quarts U.S.) 6.675?±0.125
Oil Capacity?€"Manual
Transmission (Quarts U.S.) 6.425?±0.125
Cylinder Block
Main Bearing Bore
Diameter mm (Inch) 72.401-72.422 (2.85-2.851)
Crankshaft and Flywheel
Main Bearing Journal
Diameter mm (Inch) 67.483-67-503 (2.65-2.657)
Connecting Rod Journal?€"
Diameter mm (Inch) 52.988-53.003
(2.0861-2.0867)
Crankshaft Free End Play
mm (Inch) 0.130-0.301 (0.0051-0.012)
Crankshaft Runout to Rear
Face of Block mm (Inch) 0.050 MAX (0.002)
Connecting Rod Bearings
Clearance to Crankshaft?€"
Desired mm (Inch) 0.027-0.069 (0.001-0.0027)
Clearance to Crankshaft?€"
Allowable mm (Inch) 0.027-0/069 (0.001-0.0027)
Bearing Wall Thickness
(STD) mm (Inch) 2.44-2.452 (0.096-0.0965)
Main Bearings
Clearance to Crankshaft?€"
Desired mm (Inch) 0027-0.065
(0.0011-0.0026)
Clearance to Crankshaft?€"
Allowable mm (Inch) 0.027-0.065
(0.0011-0.0026)
Bearing Wall Thickness
(STD) mm (Inch) 1.920-1.928 (0.075-0.076)
Connecting Rod, Piston and Rings
Connecting Rod?€"Piston
Pin Bore Diameter
mm (Inch) 21.959-21.979
(0.864-0.865)
Connecting Rod?€"
Crankshaft Bearing Bore
Diameter mm (Inch) 56.756-56.876 (2.234-2.24)
Connecting Rod?€"Length
(Center-to-Center)
mm (Inch) 150.7 (5.93)
Alignment (Bore-to-Bore
Max. Diff.) c ?€"Twist
mm (Inch) 0.050 per 25 (0.0015-0.984)
Alignment (Bore-to-Bore
Max. Diff.)?€"Bend
mm (Inch) 0.038 per 25 (0.0015-0.984)
Side Clearance (Assembled
to Crank)?€"Standard
mm (Inch) 0.015-0.45 (0.0006-0.0177)
Side Clearance (Assembled
to Crank)?€"Service Limit
mm (Inch) 0.05 MAX (0.02)
Crankshaft Main Bearing
Journal Taper mm (Inch) 0.020 (0.0007)
Crankshaft Main Bearing
Journal Runout mm (Inch) 0.05 (0.002)
Crankshaft Connecting Rod
Journal Taper mm (Inch) 0.015 (0.0006)

2002 2.0L Duratech.

Don't have 2004 2.3L

• NOTE: Use new connecting rod bearing cap bolts.
  NOTE: Do not fully tighten the connecting rod bearing cap bolts at this stage.
  Install the bearing caps.

• Rotate the crankshaft through 180 degrees and insert pistons 2 and 3.

• Position the corresponding bearing shells, clean and free of oil, into the connecting rod and the connecting rod bearing cap.

• Coat the inner side of the bearing shells with engine oil.

1. NOTE: The crankshaft must rotate freely, if necessary check and adjust the bearing clearances.
   Tighten the main bearing and connecting rod bearing bolts.
   1. Tighten the main bearing bolts in two stages.
      • Stage 1: 25 Nm.
      • Stage 2: 60 degrees.
   1. Tighten the connecting rod bearing bolts in two stages.
      • Stage 1: 35 Nm.
      • Stage 2: 90 degrees.