How do I remove the tension pulley on a 2007 suzuki xl7

2007 Suzuki Xl7 Fuse Diagram With 2008 Suzuki Xl7 Fuse Box Diagram PDF...

https://www.cargurus.com/Cars/Discussion-t40895_ds584763

http://www.suzuki-forums.com/2g-2007-xl7/185265-2008-xl7-oil-pressure-sensor.html

Hope these help

Suzuki XL7 Owner Manual http://www.autodealertools.com/quickQuote/manuals/2007/XL7.pdf
Suzuki XL7 Service Repair Manuals on Auto Facts

redux1"
its not XL7 , its really
a Grand Vitara, XL-7, note the DASH ! please.
no engine stated!!! there 5 engines, must we guess?
no country stated.
no real name of car. not the full name.. Grand Vitara
and it has 2 belts,
a serp belt and 1 more.
but hold my breath is the 2nd belt a serp or is it V belt.... like pumping a dry well here.


the 1 more PS slips, not the alternator belt serp
but is the other, PS slips
but the owner cant find the adjuster.
here see if you can pick and engine.
G16 i4
J20a or b, I4
H25 v6
H27 V6
or the diesel, as seen in EUROPE.
why is so hard to know whats under that hood.
???????????????????????
here is my 2004 GV , see that #5 part here.?
that adjust can be defective or set wrong.
-----------------------------------------------
here is the page, words on H25 tensionor

a) To adjust P/S pump drive belt tension, loosen tension pulley
bolts and turn tension pulley using hexagon wrench.


b) Adjust belt tension to above specification.
Then tighten tension pulley bolts to specified torque.
Tightening torque
Tension pulley bolts
25 N·m (2.5 kg-m, 18.5 lb-ft)
here is my doing this belt using my tools
see here, H27, 2004 GV

that is a large metric Allen(tm) wrench
I Also , have a 3/8"metric. that fits.
10mm Allen, hex

remove battery neg lug first. do not yank off alternator wires! until
this step is done first, or boom fire or eat acid.

which engine, we cant guess them here.
my guess H27 v6, wrong the 3.6L


all belts covered on car. (accessory)

here is a real 2007 page
seem you get lost at step 7
right>?


the alternator is NOT adjustable
so why ask this?
the $4 FSM covers this.
under drive belt replacement.
Drive Belt Replacement


Removal Procedure

Remove the air cleaner assembly. Refer to Air Cleaner Assembly Replacement .

Install the engine support fixture. Refer to Engine Support Fixture .

Remove the engine mount strut bracket. Refer to Engine Mount Strut Bracket Replacement - Right Side .

Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle .

Remove the engine splash shield. Refer to Engine Splash Shield Replacement - Right Side .

Remove the right side engine mount bracket. Refer to Engine Mount Bracket Replacement - Right Side .

Lower the vehicle.


Rotate the drive belt tensioner clockwise to release the drive belt tension.

Slide the drive belt off of the belt idler pulley (1).

Slowly release the drive belt tensioner.

Remove the drive belt from the accessory drive pulleys.
if the post was to remove alternator? is it
do above
then unbolt alt.
end guessing what you are doing....

remove door skins, card.
remove handle rods.
remove handle screws
remove handle.
or
RTM?

https://suzukipitstopplus.com/Products/10182-2007-xl7-service-manual.aspx


$4 dirt cheap, and does blow by blow, steps.

which engine option, you do know belts are not same on all engines right? fact.
2.7L V6 or bigger? IDN.

same on all cars. (answering in generic form do to above)
loosen the tension-er.
take off old
put back new
and if not a spring tension-er,set proper tension
the fSM cover all this.
why not read the manual, RTM?

here is one example (get the book, RTM or see alldata.com)

2008 xl7 engine


Removal Procedure

Remove the air cleaner assembly. Refer to Air Cleaner Assembly Replacement .

Install the engine support fixture. Refer to Engine Support Fixture .

Remove the engine mount strut bracket. Refer to Engine Mount Strut Bracket Replacement - Right Side .

Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle .

Remove the engine splash shield. Refer to Engine Splash Shield Replacement - Right Side .

Remove the right side engine mount bracket. Refer to Engine Mount Bracket Replacement - Right Side .

Lower the vehicle


Rotate the drive belt tensioner clockwise to release the drive belt tension.

Slide the drive belt off of the belt idler pulley (1).

Slowly release the drive belt tensioner.

Remove the drive belt from the accessory drive pulleys.

end remove
beg, install



Install the drive belt to the crankshaft pulley, the tensioner and the generator.

Rotate the drive belt tensioner clockwise.

Install the drive belt to the idler pulley (1).

NOTE

Important: Ensure the drive belt is properly aligned and seated into the grooves of the accessory drive pulleys.

Slowly release the drive belt tensioner.

Raise the vehicle.

Install the right side engine mount bracket. Refer to Engine Mount Bracket Replacement - Right Side .

Install the engine splash shield. Refer to Engine Splash Shield Replacement - Right Side .

Lower the vehicle.

Install the engine mount strut bracket. Refer to Engine Mount Strut Bracket Replacement - Right Side .

Remove the engine support fixture. Refer to Engine Support Fixture .

Install the the air cleaner assembly. Refer to Air Cleaner Assembly Replacement .
end.

ah, suzuki?
https://suzukipitstopplus.com/Products/1155-2007-xl7-owners-manual.aspx

they are chapter 11 here, so get em. while you still can....
usa & canada.

yes use a small socket wrench as in a 1/4 in drive i had the same problem with my echoe not a lot of room to undo bolt with a bigger ratchet...As for the belt if serpitine you need to remember how to put the belt back in there should be a tensioner pulley that you need to move to remove and replace belts however swinging alternator out of way or removing same will allow some belts to be removed if only 1

60k