2007 Chevy Cobalt P0016 crankshaft position sensor, camshaft sensor bank 1 sensor A. ? When driving down road noise from engine compartment and transmission will not shift. Any Suggestions?
SOURCE: 2001 Jeep Grand Cherokee code P1391
I would check to be sure that the timing chain hasn't jumped at all ..
SOURCE: no cruise control no passing gear traction control light on .
Replace the cam and crank sensors.
SOURCE: my check engine light came
this is usually caused by a problem with the exhaust camshaft actuator. this engine uses variable camshaft timing. there is a gear mounted on the exhaust camshaft that rotates that changes valve timing. this can can be caused by a bad gear actuator or a bad solenoid. there is a sol mounted on the right front corner of cylinder head. you can start by replacing this part and see what happens
SOURCE: camshaft position sensor correlation bank 1 code
timing belt is off by a tooth or two. you probably didn\'t have to replace the coolant sensor; that code sets whenever the sensor is disconnected and the ignition is turned on; and it needs to be reset by disconnecting the battery or with a code reader. anyway, the crank/ cam sensors are out of sync. if you\'ve got the twin cam engine, they are a royal pain to get the belt to lay properly on the two cams.
Testimonial: "got it in time but it is giving a p0016 code, and at around 30 mph the rev limiter is coming on"
SOURCE: where are the camshaft and crankshaft position sensors on 2001 silverado 8.1 V8
Crank shaft sensor
Remove the driver side rear ignition coil bolts. Reposition the coil. Disconnect the crankshaft position (CKP) sensor electrical connector. # Use penetrating oil and allow the oil to soak around the CKP sensor prior to removing the sensor. You're looking at left, rear side of engine.
CAMSHAFT POS.
front side of engine on the drives side about half way up the timing cover, not hard to get to.
Crankshaft -camshaft timing misalignment bank 1 sensor 1
- The pcm detects that the camshaft position is out of phase with the crankshaft position
Probable Cause[s]
Generic OBD II Diagnostic Trouble Codes
DTC CODES P0300 to P0399
P0300....Random/Multiple Cylinder Misfire Detected
P0301....Cylinder 1 Misfire Detected
P0302....Cylinder 2 Misfire Detected
P0303....Cylinder 3 Misfire Detected
P0304....Cylinder 4 Misfire Detected
P0305....Cylinder 5 Misfire Detected
P0306....Cylinder 6 Misfire Detected
P0307....Cylinder 7 Misfire Detected
P0308....Cylinder 8 Misfire Detected
P0309....Cylinder 9 Misfire Detected
P0310....Cylinder 10....Misfire Detected
P0311....Cylinder 11 Misfire Detected
P0312....Cylinder 12 Misfire Detected
P0313....Misfire Detected with Low Fuel
P0314....Single Cylinder Misfire (Cylinder not Specified)
P0320....Ignition/Distributor Engine Speed Input Circuit
P0321....Ignition/Distributor Engine Speed Input Circuit Range/Performance
P0322....Ignition/Distributor Engine Speed Input Circuit No Signal
P0323....Ignition/Distributor Engine Speed Input Circuit Intermittent
P0324....Knock Control System Error
P0325....Knock Sensor 1 Circuit (Bank 1 or Single Sensor)
P0326....Knock Sensor 1 Circuit Range/Performance (Bank 1 or Single Sensor)
P0327....Knock Sensor 1 Circuit Low Input (Bank 1 or Single Sensor)
P0328....Knock Sensor 1 Circuit High Input (Bank 1 or Single Sensor)
P0329....Knock Sensor 1 Circuit Input Intermittent (Bank 1 or Single Sensor)
P0330....Knock Sensor 2 Circuit (Bank 2)
P0331....Knock Sensor 2 Circuit Range/Performance (Bank 2)
P0332....Knock Sensor 2 Circuit Low Input (Bank 2)
P0333....Knock Sensor 2 Circuit High Input (Bank 2)
P0334....Knock Sensor 2 Circuit Input Intermittent (Bank 2)
P0335....Crankshaft Position Sensor A Circuit
P0336....Crankshaft Position Sensor A Circuit Range/Performance
P0337....Crankshaft Position Sensor A Circuit Low Input
P0338....Crankshaft Position Sensor A Circuit High Input
P0339....Crankshaft Position Sensor A Circuit Intermittent
P0340....Camshaft Position Sensor 'A' Circuit (Bank 1 or Single Sensor)
P0341 Camshaft Position Sensor 'A' Circuit Range/Performance (Bank 1 or Single Sensor)
P0342....Camshaft Position Sensor 'A' Circuit Low Input (Bank 1 or Single Sensor)
P0343....Camshaft Position Sensor 'A' Circuit High Input (Bank 1 or Single Sensor)
P0344....Camshaft Position Sensor 'A' Circuit Intermittent (Bank 1 or Single Sensor)
P0345....Camshaft Position Sensor 'A' Circuit (Bank 2)
P0346....Camshaft Position Sensor 'A' Circuit Range/Performance (Bank 2)
P0347....Camshaft Position Sensor 'A' Circuit Low Input (Bank 2)
P0348....Camshaft Position Sensor 'A' Circuit High Input (Bank 2)
P0349....Camshaft Position Sensor 'A' Circuit Intermittent (Bank 2)
P0350....Ignition Coil Primary/Secondary Circuit
4,398 views
Usually answered in minutes!
×