It says on obdii detector that mil is off inquiry on egr 7 monitors ready no check engine light is on
SOURCE: 2000 Honda Accord EGR Valve Error P0401
Jason,
-after you change the part you have to reset/clear the code
-this can be done by either:
(1) using the OBD2 code reader that Autozone used OR since option 2 (below) is very quick
(2) disconnecting the battery for about 30 seconds (this will delete
all codes/radio presets/etc) but it will also clear the 'check engine'
code
-this is what I do AFTER i write down my radio station presets :)
-hopefully the new EGR valve resolves your issue after you CLEAR the code
...but that code just means a an insufficient amount of Exhaust Gas
recirculation (pressure difference) used to keep the emissions in check
-if it comes back, then there are a few other fixes to try also
-let me know if you need further assistance
-please remember to rate me `fix-ya`if it works
thanks
SOURCE: OBD code 0401 (1997 Toyota Camry 4 cyl)
There is a VSV (vacuum switching valve) , usually mounted on the back side of engine block, under the intake manifold, as well as the map sensor, that can also cause that code if one or the other is faulty. It takes some pretty detailed troubleshooting to confirm this in some cases, so if that's not in your line of work, you may have to have it properly diagnosed, or take a 50/50 shot at which one first.
SOURCE: odeometer and clock lights
Just replaced bulb on my 2002 Accord EX. Simple to do.
1. Lift up the trim piece around clock; just slide a putty knife under and lift.
2. Take out assembly and look on underside for small gray bulb base ( about 3/16 dia.). It helps if you have the new one to compare.
3. Use small blade screwdriver in slot and rotate counterclockwise to remove. You may have to shake it to get out.
4. Examine the new bulb to find the slots that DO NOT have wires. Put bulb into socket and rotate clockwise with screwdriver in proper slot.
That's it; you now are there.
SOURCE: check engine light comes on and off, auto zone
The EGR valve helps your car more efficiently and completely burn fuel
by recirculating a portion of your exhaust and running it through the
combustion process again. When the EGR valve goes bad, it must be replaced.
The EGR valve, or Exhaust Gas Recirculation valve, is a vacuum
controlled valve which allows a specific amount of your exhaust back
into the intake manifold. This exhaust mixes with the intake air and
actually cools the combustion process. Cooler is always better inside
your engine. The exhaust your EGR valve recirculates also prevents the
formation of Nitrogen related gases. These are referred to as NOX
emissions, and are a common cause for failing emissions testing.
Unfortunately, your EGR valve can get stuck, causing NOX gases to build
up. You'll know if your EGR valve is stuck or malfunctioning because
your car will experience symptoms like rough idle and bucking on
acceleration.
Here is a picture of where the EGR
Valve is located (Accord 1999). Replacing it is fairly simple and straightforward. A
vacuum line and a couple of bolts. You'll see what you have to do when
you look at it.
If you
are replacing the EGR Valve due to the Check Engine Light (MIL) being
on with a DTC P0401 then I suggest contacting your Honda Dealer. There
was a Product Update Campaign (PUD) in the fall of 1999 that corrected
the problem.
Another times, the clean is the solution...I hope help yoiu with this. Good luck, and remember rated this help.
Testimonial: "Thank you very much your knowledge and information you offered concerning my problem and following questions were VERY helpful!(I lost owners manual)"
SOURCE: 2002 Honda Accord V6 check engine light on- local
po505 idle air control if this is the code all hondas do it eventully, small problem easy fix u have 2 choices either remove the idle air control motor and clean the inside of it u will find it's black and the spring inside is stuck clean it with carb cleaner or gum cutter any parts store will have this it's a dirty job it will work for awhile but to replace it is recommended its not expensive for a new one which u can get at any autoparts store autozone,advanced,napa etc. there is only 2 bolts in most cases maybe 3 i doubt it though if u go online t google and type in th eyear make and model and engine size in ur case it's a 3.0 v6 and look for idle air control locations u'll find it to do this job a shop will charge u anywhere from 100.00 for diag to retrive the code plus the part and the labor so about 250.00-375.00 it will only take u honestly maybe 15 minutes to perform only tools needed are a 10 millimeter wrench there is only 1 connector to disconnect and ur done if u do this u will still have the check engine light because u have not cleared it from the computer to do this just disconnect the negative battery terminal (the black one or has a neg sign - don't disconnect the positive side +)for 5 minutes then reconnect and the computer will have reset no more light. good luck it really is that easy
209 views
Usually answered in minutes!
I meant which monitors of the previous seven are they ? Thank you
×