My 98 acura was stuck in park and wouldnt start. I overrode the gear shift and put it it in neutral. no start. Had it towed. Found the 20 amp brake fuse keeps blowing. Still wont start. Cant figure it out. Help!!

Use your key in the slot next to the gearshift. If your brake lights aren't working it won't let you put the car in gear. This slot is an emergency switch to allow you to move the car out of park to move or tow it. Either your brake light switch is bad or both brake light bulbs are out.

Hi,
Try releasing your parking brake and having someone push or rock your car. Sometimes the gearbox gets stuck in Park if the car moves after you put the car in Park and let the car roll a bit before applying the handbrake. It could also be a fault with the gearbox itself.
Its also possible that the locking tab mechanism (that gets relesed when you press the button on your auto gear shift) has jammed. If you can get it out of Park do not put the car back into Park ,but rather put it in Neutral after you have finished driving around etc and use the hand brake when parking. At least you wont be stuck in Park until you get it to the repair shop. Note that your car can roll in Neutral, especially if your parking brakes are worn, so take extra care when parking ie point your wheels toward the kerb when parking on any hills or slopes.
Any time your gearbox gets stuck its a fair bet that you need to get your gearbox inspected by an authorized repairer.
Good luck,
Steve (Melbourne, Australia)

Yes it can, just place your Transfer Case in Neutral position.
Shifting into NEUTRAL
To shift the transfer case to NEUTRAL do the following:

Make sure the vehicle is parked so that it will not roll.
Set the parking brake.
Start the vehicle or turn the ignition to RUN.
Connect the vehicle to the towing vehicle.
Put the transmission in NEUTRAL (N).
Shift the transfer case to 2HI.
Simultaneously press and hold the 2HI and 4LO buttons for 10 seconds. The red NEUTRAL light will come on when the transfer case shift to NEUTRAL is complete.
Shift the transmission to REVERSE (R) for one second, then shift the transmission to DRIVE (D) for one second, or FIRST (1) for vehicles equipped with a manual transmission.
Turn the ignition to LOCK.
Place the transmission shift lever in PARK (P), or FIRST (1) for vehicles with a manual transmission.
Release the parking brake prior to towing.
Shifting Out of NEUTRAL
To shift out of NEUTRAL:

Set the parking brake and apply the regular brake pedal.
Shift the transmission to NEUTRAL (N) and turn the ignition to RUN with the engine off.
Press the button for the desired transfer case shift position (2HI, 4HI, AUTO 4WD or 4LO).
After the transfer case has shifted out of NEUTRAL the red light will go out.
Release the parking brake.
You may start the engine and shift the transmission to the desired position.
Excessively shifting the transfer case into or out of the different modes may cause the transfer case to enter the shift protection mode. This will protect the transfer case from possible damage and will only allow the transfer case to respond to one shift per 10 seconds. The transfer case may stay in this mode for up to three minutes.
NEUTRAL: Shift the vehicle's transfer case to NEUTRAL only when towing your vehicle.
Good luck and hope this answers your question.

Shifting to NEUTRAL
To shift the transfer case to NEUTRAL, first make sure
the vehicle is parked so that it will not roll:
1. Set the parking brake.
2. Start the vehicle.
3. Connect the vehicle to the towing vehicle.
4. Put the transmission in NEUTRAL (N) or have
the clutch pedal pressed for vehicles with
manual transmission.
5. Shift the transfer case to 2HI.
6. Simultaneously press and hold the 2HI and
4LO buttons for 10 seconds. The red NEUTRAL
light will come on when the transfer case shift to
NEUTRAL is complete.
7. Shift the transmission to REVERSE (R) for one
second, then shift the transmission to DRIVE (D)
for one second or FIRST (1) for vehicles with
manual transmission.
8. Turn the ignition to OFF.
9. Place the transmission shift lever in PARK (P) or
FIRST (1) for vehicles with manual transmission.
10. Release the parking brake prior to towing.

************************

Shifting Out of NEUTRAL
To shift out of NEUTRAL:
1. Set the parking brake and apply the regular
brake pedal.
2. Start the vehicle with the transmission in PARK (P)
or FIRST (1) for vehicles with manual transmission.
3. Press the button for the desired transfer case position
(2HI, 4HI, AUTO 4WD or 4LO).
4. Put the transmission in NEUTRAL (N) or press the
clutch pedal for vehicles with manual transmission.
5. Shift the transmission lever to the desired position.
After the transfer case has shifted out of NEUTRAL,
the red light will go out.
6. A re-engagement sound is normal when shifting out
of NEUTRAL.

You can remove the interlock off the gear shift or maybe spray some crc on it otherwise probably a loose wire or switch

I have a jeep wrangler and to have it towed you are suppose to put the transverecase in neutral after you first depress brake pedal put trans in neutral then start engine shift auto trans into drive release brake pedal make sure there is no movement, shut engine off with key left in acc position shift auto trans into park, disconnect neg battery cable (damage can result in trans if shifted into park while transvere case is in neutral with engine running) you should refere to your owners manuel

There's a saftey cable attached to the brake. If that breaks or gets messed up you will not be able to get it out of park. There might be a key slot in the console,insert the ignition key, & try to move the gear shift. If you can get to neutral,it'll start & you can get it to a qualified shop,without a tow bill.

THERE IS A SENSOR ON THE BRAKE PEDAL THAT RELEASES THE THE SHIFTER.THERE A 3 COMPONENTS INVOLVED.U CAN PUT IT IN NEUTRAL BEFORE U START THE CAR.THEN WIL SHIFT.

sounds like your brake/shift interlock solenoid is not releasing.
Your owner manual will tell you how to bypass in emergency.
Check your fuse first. fuse panel on instrument panel.

Please rate as fixed if this helps.

Fuse 23 - 1 5 amp
Fuse 34 - 7 1/2 amp

check enigne light not related.
----------------------------------------------------

The selector lever lock can be moved mechanically out of position ”P" when for example the battery is disconnected or completely discharged.
Using a ball point pen or similar item as an unlocking lever, push forward and hold in position.

Move the selector lever out of position "P".

NOTE: If the selector lever is moved back to ”P" it is re-locked.

Selector Lever Lock

When you turn ignition on it releases a cable that is attached to the shifter also the shifter has a solenoid attached to it that is released when you step on the brake. Both times that I had the problem of button stuck and cant shift out of park the solenoid was sticking and wouldnt release .