Don't know liter size of engine? The picture is for 2.4L.
SOURCE: serpentine belt diagram:
The belt routing diagram is located on the top radiator cross member by the hood latch. You should see it when you open the hood. If it is not there, all Chrysler, Dodge, and Plymouth minivans, from 1993 to at least 1999, used the same 3.3L engine setup, so find someone with one and look for the diagram where I described.
SOURCE: need diagram for 2000 dodge dakota serpentine belt
On the 1999 Dakota with the 3.9liter, the fan shroud absolutely DOES NOT have to be removed. Very simple job. Simply use a breaker bar with a 15mm socket on the belt tesioner pulley nut. Using the breaker bar push (as though tightening) the pulley nut...the reaction will be that the tensioner removes tension from the pulley and the entire belt can be removed by easily slipping it toward the front of the vehicle...comes right off. The new belt can go back on in exactly the same manner. By the way the belt routing diagram IS CONVIENENTLY LOCATED between the hood latch and the radiator mounting for simple and quick refernce...one person job, I did removal and installation four times in less than 10 minutes. (why four times? The auto parts store was selling replacement belts that were too long and did not allow the belt tensioner to provide suffiecient tension...I had to try four different manufacturers before the tensioner was adequately tight with room to grow as the belt naturally stretches from use.). I found no stringing around the fan is required because of the way the belt is routed (it doglegs around the main engine pulley which is centered below the fanhousing and then the belt runs from there to the left side of the fan housing...avoiding the fan/fanhousing all-together (sure you can try to go past the fan/fan housing if you so desire...but you dont have to...and besides the space between the pulleys and the fan is ample to allow the belt to pass between with minimal interference or a simple rotation of the fan as you attempt this method. One hint that made my installs easy as pie...the last pulley you put it over should not be a bezeled and ridged pulley or you will needlessly make life difficult for yourself...the last pulley should be the water pump pulley which is a smooth bore and non-ridged pulley (makes you wonder how the belt even stays on it!)...making it easy as pie to slip it right over...as your last act of defiance to that mean old serpentine belt!
SOURCE: I need a serpentine belt diagram for a 2004 dodge ram 1500
By chance, have you looked on the underside of your hood, most, if not all vehicles have the diagram there, it should be a white sticker with the pulleys and everything.
SOURCE: I need a serpentine belt diagram for adodge
Here's your belt diagram.
if it's not correct let me know and I'll get you all the routing diagram for that year ram 1500.
Hope it helps.
SOURCE: Need serpentine belt routing diagram for 1994 Dodge grand caravan
3.3L?
Looking at the engine from front (right side of the Van): Stating at the Top, Going Left to Right and Clockwise:
Over the Alternator
To under the Idle Pulley,
To Over the AC Compressor.
To the Left Side of the Water Pump.
To the Right side and Under the Crankshaft Pulley
To the Right side and Over and Down the Tensioner
To Under the Power Steering Pump
And Back up-to the Left side of the Alternator.
Advise when puting it on:
Put the Belt around everything else accept for the Alternator. After it is around all the rest of the Pulleys - Pull the belt up - tight from the Power steering Pump and the Idle Pulley to form a loop, holding the Belt close to the Altenator Pulley.
Using the 15mm wrench or belt tensioner bar - rotate the Tensioner Pulley towards the front of the Van and then place the belt over the Alternator.
Let me know if this helped or if you have additional information or questions. Feel free to contact me at FixYa.com!
23,605 views
Usually answered in minutes!
×