Question about 1999 Suzuki Esteem

Open Question

ENGINE DIAGRAM 1999 SUZUKI ESTEEM RADIATOR AND COOLING SYSTEM AND HEATER

THIS METAL PIECE ATTACHES TO THE BLOCK HAS A HOSE CLAMP AT BOTH ENDS

Posted by on

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Anonymous

  • 1 Answer

SOURCE: Suzuki Baleno (esteem) 1999. Engine Idle RPM not stable

you probably need to check the butterfly. its the compinent that controls how much air goes into the engine if it is weared than in idle state air leaks into the engine sometime more sometimes less and cause fluctuations in rpm

secondly there is a rpm switch which controls the rpm you can replace that switch and check

Posted on Jun 28, 2009

Ad

Richard Scordino

  • 6982 Answers

SOURCE: 1998 suzuki esteem 1.6 will not start HELP!

Having good fuel pressure is a plus (yours seems a bit high but I don't have specs) What you need to find out is if the injectors are opening and putting the fuel into the engine so it can work. Are the plugs wet with fuel or dry? Does it fire up if you spray carb cleaner into the throttle body while cranking?

Posted on Aug 30, 2009

Testimonial: "thanks for quick reply..will pull plugs and inspect..wow what a great site!"

Anonymous

  • 59 Answers

SOURCE: 1999 suzuki grand vitara has power steering leak

That is the power steering cooler/pressure line. You can either replace it with another steel of same diameter or call the dealer and order it from them. But it could get pricey.

Posted on Sep 01, 2009

Anonymous

  • 102 Answers

SOURCE: 1999 suzuki esteem fuel filter location

This is a Baleno in our market (Australia) and the G16B 1.6 EFI SOHC 16v has the fuel filter bolted to the firewall in the engine bay. This fuel system will be under pressure even after the engine has been off for a long period of time.

Posted on Oct 07, 2009

Anonymous

  • 1 Answer

SOURCE: Have replaced radiator. Have bled cooling system.

blend doors recalibrate,the stop point connected to the actuator breaks.

Posted on Dec 04, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2000 suzuki esteem 1.6 litre over heating


May need to bleed the air out of the system after the hose change. Look for small bleed valve on the top engine or cooling hoes/pipe bleed slowly while engine is at operating temp, then refill after reservoir after car cools down

Dec 27, 2013 | 2000 Suzuki Esteem

2 Answers

Engine Diagrams


Hello. Here a non-photo diagram. Hope this helps!!!

The thermostat is located on the side of the water pump, the water pump is located just above the a/c compressor, the thermostat is fed coolant from the radiators lower radiator hose.
Thermostat :
1. drain coolant and tighten drain plug ( easier method : remove radiator cap, get big drain pan, place drain pan under lower radiator hose to radiator connection, remove clamp, slowly remove hose, allow coolant to drain into pan, now is a good time to remove radiator hose and clamp from thermostat housing )
2. remove thermostat cover / cap ( easiest to get at this when front of car is supported by jack stands and right hand side lower cover is removed ).
3. thermostat cap is held on by 3 bolts / remove thermostat.

You will notice that the thermostat's air bleed hole is pointing up and lines up with notch in water pump housing,,

ATTENTION :failure to install new thermostat in the correct location will cause engine to overheat.

1. install new thermostat to water pump, make sure air bleed hole lines up with notch, install and tighten bolts, install a new lower radiator hose, fill cooling system.

thermostat # 17670-77E00
lower radiator hose #17854-65G20
hose clamp #09401-36403
upper radiator hose # 17852-65G20

Suzuki factory manual

Oct 21, 2013 | Cars & Trucks

1 Answer

Need diagram showing Heater Hose connection points. Upper heater hose connects to a pipe along the left front side of engine which travels dow the left side and elbows torwards the radiator under the...


try the scrapyard and look at one in their ,or ask a local owner that is just parking up in a supermarket and look at theirs .lots of different ways to overcome this problem but if the pipe has beeen disconnected its because the heater matrix is no doubt leaking

Nov 03, 2011 | 1993 Cadillac DeVille

1 Answer

Donde esta el termostato del 300 1999 chrysler


3.2L & 3.5L Engines
  1. Disconnect negative cable
  2. Drain cooling system.
  3. Raise vehicle on hoist.
  4. Disconnect electrical connectors from engine oil and power steering pressure switches.
  5. Disconnect radiator and heater hoses from thermostat housing.
  6. Remove thermostat housing bolts.
  7. Remove housing, thermostat, and gasket.

To install:

  1. Position gasket on thermostat and housing.
  2. Install thermostat housing, gasket and mounting bolts onto block. Tighten attaching bolts to 105 inch lbs. (12 Nm).
  3. Install radiator hose.
  4. Install bypass hose.
  5. Connect electrical connectors from engine oil and power steering pressure switches.
  6. Connect negative cable.
  7. Fill cooling system.
  8. Inspect for leaks.
  9. Lower vehicle on hoist.

Jan 23, 2011 | 1999 Chrysler 300M

1 Answer

Where is the thermostat located on the 1999 esteem wagon


following the top radiator hose to the engine block, look where it connects to the engine. just under the hose, you see some bolts. that is the thermostat housing cap. remove the hose, and remove the cap, and there you are. When you replace the thermostat, make sure you clean the cap and engine block to shiny metal..you want no leaks from the old gasket. When you buy the new thermostat, make sure you get a gasket with it. some companies do not include the gasket anymore. Make you spend more money. easy job to do, takes about 30 minutes to do. hope this helps

Jan 08, 2011 | 1999 Suzuki Esteem

1 Answer

Two cooling hoses going to my firewall is broken on my silverado truck 2000


Those are the inlet and outlet hoses to your heater core. The hoses are probably a specific form fitted hose that you can get at the counter of any parts store. There is a clamp on both sides of the hoses. Remove them and then use a razor blade to cut the hoses off. Be sure the engine is cool and the radiator cap is off. Place a catch bin under the hoses because coolant will come out. put some coolant on the inside end of the new hoses to make them easier to install. Buy new clamps also. The heater core necks where the hoses attach can break unless you are gentle and careful. Trust me, you don't want to replace a heater core unless it is absolutely necessary.

May 21, 2010 | 1999 Chevrolet Silverado 1500

1 Answer

Remove thermostat


300M, Concorde, Intrepid, LHS, 1998-2004
THERMOSTAT - Removal & Installation

2.7L Engine
  1. Disconnect negative cable.
    CAUTION Do not remove pressure cap with the system hot and under pressure because serious burns from coolant can occur.
  2. Drain cooling system.
  3. Remove radiator lower hose from thermostat housing.
  4. Remove nuts from heater tube flange studs.
  5. Loosen starter bolt at heater tube bracket.
  6. Pull heater tube out of thermostat housing and position out of the way.
  7. Remove bolt and two studs.
  8. Remove thermostat housing, O-ring and thermostat.
  9. Remove thermostat housing bolts.

To install:
  1. Clean gasket sealing surfaces.
    NOTE Install thermostat with the bleed valve located at the 12 o'clock position, between tabs on seal.
  2. Install thermostat and seal into thermostat housing .
  3. If removed, install two studs.
  4. Install thermostat, thermostat housing and O-ring and bolt. Tighten attaching bolts to 105 inch lbs.(12 Nm).
  5. Lubricate new heater return tube O-ring with coolant.
  6. Position heater return tube flange over two studs. Install nuts.
  7. Tighten retaining nuts to 53 inch lbs.(6 Nm).
  8. Tighten starter bolt to 40 ft. lbs. (54.3 Nm).
  9. Connect the lower radiator hose to the thermostat housing. Install hose clamps.
  10. Refill cooling system.
  11. Inspect for leaks.
  12. Connect negative cable.

3.2L & 3.5L Engines
  1. Disconnect negative cable.
    CAUTION Do not remove pressure cap with the system hot and under pressure because serious burns from coolant can occur.
  2. Drain cooling system.
  3. Raise vehicle on hoist.
  4. Disconnect electrical connectors from engine oil and power steering pressure switches.
  5. Disconnect radiator and heater hoses from thermostat housing.
  6. Remove thermostat housing bolts.
  7. Remove housing, thermostat, and gasket.
    NOTE The OEM thermostat is staked in place at the factory. To ensure proper seating of replacement thermostat, carefully remove the bulged metal from the thermostat housing using a suitable hand held grinder. It is not necessary to restake the replacement thermostat into the thermostat housing.

To install:
  1. Position gasket on thermostat and housing.
  2. Install thermostat housing, gasket and mounting bolts onto block. Tighten attaching bolts to 105 inch lbs. (12 Nm).
  3. Install radiator hose.
  4. Install bypass hose.
  5. Connect electrical connectors from engine oil and power steering pressure switches.
  6. Connect negative cable.
  7. Fill cooling system.
  8. Inspect for leaks.
  9. Lower vehicle on hoist.

Hope this help (remember comment and rated this).

Apr 04, 2010 | 2000 Chrysler Concorde

1 Answer

How to replace thermostat


300M, Concorde, Intrepid, LHS, 1998-2004 - Thermostat Removal & Installation 2.7L Engine
  1. Disconnect negative cable.
    CAUTION Do not remove pressure cap with the system hot and under pressure because serious burns from coolant can occur.
  2. Drain cooling system.
  3. Remove radiator lower hose from thermostat housing.
  4. Remove nuts from heater tube flange studs.
  5. Loosen starter bolt at heater tube bracket.
  6. Pull heater tube out of thermostat housing and position out of the way.
  7. Remove bolt and two studs.
  8. Remove thermostat housing, O-ring and thermostat.
  9. Remove thermostat housing bolts.
To install:
  1. Clean gasket sealing surfaces.
    NOTE Install thermostat with the bleed valve located at the 12 o'clock position, between tabs on seal.
  2. Install thermostat and seal into thermostat housing .
  3. If removed, install two studs.
  4. Install thermostat, thermostat housing and O-ring and bolt. Tighten attaching bolts to 105 inch lbs.(12 Nm).
  5. Lubricate new heater return tube O-ring with coolant.
  6. Position heater return tube flange over two studs. Install nuts.
  7. Tighten retaining nuts to 53 inch lbs.(6 Nm).
  8. Tighten starter bolt to 40 ft. lbs. (54.3 Nm).
  9. Connect the lower radiator hose to the thermostat housing. Install hose clamps.
  10. Refill cooling system.
  11. Inspect for leaks.
  12. Connect negative cable.
3.2L & 3.5L Engines
  1. Disconnect negative cable.
    CAUTION Do not remove pressure cap with the system hot and under pressure because serious burns from coolant can occur.

  2. Drain cooling system.
  3. Raise vehicle on hoist.
  4. Disconnect electrical connectors from engine oil and power steering pressure switches.
  5. Disconnect radiator and heater hoses from thermostat housing.
  6. Remove thermostat housing bolts.
  7. Remove housing, thermostat, and gasket.
    NOTE The OEM thermostat is staked in place at the factory. To ensure proper seating of replacement thermostat, carefully remove the bulged metal from the thermostat housing using a suitable hand held grinder. It is not necessary to restake the replacement thermostat into the thermostat housing.
To install:
  1. Position gasket on thermostat and housing.
  2. Install thermostat housing, gasket and mounting bolts onto block. Tighten attaching bolts to 105 inch lbs. (12 Nm).
  3. Install radiator hose.
  4. Install bypass hose.
  5. Connect electrical connectors from engine oil and power steering pressure switches.
  6. Connect negative cable.
  7. Fill cooling system.
  8. Inspect for leaks.
  9. Lower vehicle on hoist.

Hope helps with this (remember rated this) Good luck.

Feb 02, 2010 | 2001 Chrysler 300M

1 Answer

How do you replace a radiator in a dodge shadow 1993


These are the instructions for a 4 cylinder motor.

  1. Disconnect the negative (-) battery cable.

CAUTION Do NOT remove the cylinder block or the radiator draincock with the system hot and under pressure because serious burns from coolant can occur.
  1. Drain the cooling system.
  2. Remove the hose clamps and hoses from the radiator. Remove the coolant reserve system tank-to-filler neck tube.
  3. Remove the automatic transaxle hoses, if so equipped.
  4. Remove the fan and fan support assembly by disconnecting the fan motor electrical wiring.
  5. Remove the fan shroud retaining clips, located on the top and bottom of the shroud for most of the vehicles (the Dynasty has them only on the top).
  6. Lift the shroud up and out of the bottom shroud attachment clips separating the shroud from the radiator. Avoid damaging the fan.
  7. Remove the upper radiator mounting screws. Disconnect the engine block heater wire, if so equipped.
  8. Remove the air conditioning condenser attaching screws located at the top front of the radiator, if the vehicle is equipped with air conditioning.
  9. Lift the radiator free of the engine compartment.
Care should be taken to NOT damage the radiator cooling fins or water tubes during removal or installation.
To install:
  1. Slide the radiator down into position behind the radiator support.
  2. Attach the air conditioning condenser to the radiator, if so equipped, with a force of approximately 10 lbs. (44 N) to seat the radiator assembly lower rubber isolators in the mount holes provided.
  3. Tighten the radiator mounting screws to 108 inch lbs. (12 Nm).
  4. Connect the automatic transaxle hoses, if so equipped. Tighten the hose clamps to 35 inch lbs. (4 Nm).
  5. Slide the fan shroud, fan and motor down into the clips on the lower radiator flange. Install new shroud retaining clips.
  6. Install the upper and lower radiator hoses (including the coolant reserve hose).
  7. Plug the fan motor electrical connection and attach the negative (-) battery cable.
  8. Fill the cooling system with coolant (refer to Section 1 for more details).
  9. Operate the engine until it reaches normal operating temperature. Check the cooling system and automatic transaxle (if equipped) for the correct fluid levels. Also check for coolant leaks.
Here are the instruction for a 6 cylinder engine.
6-Cylinder Engines
  1. Disconnect the negative (-) battery cable.

CAUTION Do NOT remove the cylinder block or the radiator draincock with the system hot and under pressure because serious burns from coolant can occur.
  1. Drain the cooling system.
  2. Remove the hose clamps and hoses from the radiator. Remove the coolant reserve system tank to filler neck tube.



  1. Remove the automatic transaxle hoses, if so equipped.
  2. Remove the fan and fan support assembly by disconnecting the fan motor electrical wiring.
  3. Remove the fan shroud retaining clips, located on the top and bottom of the shroud for most of the vehicles (the New Yorker, Dynasty, Fifth Ave., and Imperial have them only on the top).
  4. Lift the shroud up and out of the bottom shroud attachment clips separating the shroud from the radiator. Avoid damaging the fan.
  5. Remove the upper radiator mounting screws. Disconnect the engine block heater wire, if so equipped.
  6. Remove the air conditioning condenser attaching screws located at the top front of the radiator, if the vehicle is equipped with air conditioning.
  7. Lift the radiator free of the engine compartment.
Care should be taken NOT to damage the radiator cooling fins or water tubes during removal or installation.


To install:
  1. Slide the radiator down into position behind the radiator support.
  2. Attach the air conditioning condenser to the radiator, if so equipped, with a force of approximately 10 lbs. (44 N) to seat the radiator assembly lower rubber isolators in the mount holes provided.
  3. Tighten the radiator mounting screws to 9 ft. lbs. (12 Nm).
  4. Connect the automatic transaxle hoses, if so equipped. Tighten the hose clamps to 35 inch lbs. (4 Nm).
  5. Slide the fan shroud, fan and motor down into the clips on the lower radiator flange. Install new shroud retaining clips.
  6. Install the upper and lower radiator hoses (including the coolant reserve hose).
  7. Plug the fan motor electrical connection and attach the negative (-) battery cable.
  8. Fill the cooling system with coolant (refer to Section 1 for more details).
  9. Operate the engine until it reaches normal operating temperature. Check the cooling system and automatic transaxle for the correct fluid levels. Also check for coolant leaks.
please let me know if i can assist you in any further problems you may encounter with your vehicle.
please do not forget to rate and comment about your experience with fixya today.


Dec 27, 2009 | 1993 Dodge Shadow

1 Answer

I need to know where the location of the thermostat is on a 1999 chrysler 300m so i can replace


The 2.7L engine lower radiator hose, connects to the thermostat housing.

To Remove:
1.Disconnect the Negative battery cable.
(Engine COLD!)
  1. Drain cooling system.
  2. Remove radiator lower hose from thermostat housing.
  3. Remove nuts from heater tube flange studs.
  4. Loosen starter bolt at heater tube bracket.
  5. Pull heater tube out of thermostat housing and position out of the way.
  6. Remove bolt and two studs.
  7. Remove thermostat housing, O-ring and thermostat.
  8. Remove thermostat housing bolts.
To install:
A.Clean gasket sealing surfaces.
B.Install thermostat with the bleed valve located at the 12 o'clock position, between tabs on seal.
  1. Install thermostat and seal into thermostat housing .
  2. If removed, install two studs.
  3. Install thermostat, thermostat housing and O-ring and bolt. Tighten attaching bolts to 105 inch lbs.(12 Nm).
  4. Lubricate new heater return tube O-ring with coolant.
  5. Position heater return tube flange over two studs. Install nuts.
  6. Tighten retaining nuts to 53 inch lbs.(6 Nm).
  7. Tighten starter bolt to 40 ft. lbs. (54.3 Nm).
  8. Connect the lower radiator hose to the thermostat housing. Install hose clamps.
  9. Refill cooling system.
  10. Inspect for leaks.
  11. Connect negative cable.
3.2 and 3.5L engines:
Disconnect the battery cable. (Again engine COLD)
  1. Drain cooling system.
  2. Raise vehicle on hoist.
  3. Disconnect electrical connectors from engine oil and power steering pressure switches.
  4. Disconnect radiator and heater hoses from thermostat housing.
  5. Remove thermostat housing bolts.
  6. Remove housing, thermostat, and gasket.
The OEM thermostat is staked in place at the factory. To ensure proper seating of replacement thermostat, carefully remove the bulged metal from the thermostat housing, using a suitable hand held grinder. It is not necessary to restake the replacement thermostat, into the thermostat housing.

To Install:
  1. Position gasket on thermostat and housing.
  2. Install thermostat housing, gasket and mounting bolts onto block. Tighten attaching bolts to 105 inch lbs. (12 Nm).
  3. Install radiator hose.
  4. Install bypass hose.
  5. Connect electrical connectors from engine oil and power steering pressure switches.
  6. Connect negative cable.
  7. Fill cooling system.
  8. Inspect for leaks.
  9. Lower vehicle on hoist.
From AutoZone Repair Guides

I feel this way, I can give you an accurate description, and have taken into account your safety.

May 12, 2009 | 1999 Chrysler 300M

Not finding what you are looking for?
1999 Suzuki Esteem Logo

Related Topics:

65 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts

Marvin
Marvin

Level 3 Expert

85222 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...