2003 Chevy Express 3500 tie rods and ball joints torque spec?

• Axle Shaft nut - 177 ft-lb
• Hub and bearing assembly to steering knuckle bolts - 133 ft-lb

2003 chevy silverado 1500 4.3 v6. Changing steering rack and

https://www.justanswer.com > ... > Chevrolet Repair
Jan 11, 2021 - Below are the torque specs you requested: Steering Rack-to-frame mounting bolts: 136 lb. ft. Outer tie rod nut: 37 lb. ft. Outer tie rod ...
1 answer · 1 vote: Coupler clamp bolt to the intermediate shaft: 33 ft. lb.

• 
  

  Torque specs for tie rod end castle nuts - JustAnswer

  https://www.justanswer.com > chevy > 2p3g8-torque-sp...
  Oct 24, 2009 - Tighten the clamp nuts 18 ft. lbs. (25 Nm) (except C3HD). On C3HD models, tighten the clamp nuts to 65 ft. lbs. (88 Nm.

People also ask

Question edited for clarity.

Question moved to sub category.

Torque Specs ' Chevy Impala SS Forum

https://www.impalassforum.com > ... > Suspension
Mar 27, 2004 - Lower Ball Joint - 75 - 80 ft lbs. Inner & Outter Tie Rods - 35 ft lbs. Centerlink - 35 ft lbs. Idler - 35 ft lbs. Upper control arm shaft - 92 ...
Torque specs for rear control arm. ' Chevy Impala SS Forum
Oct 5, 2003
Front lower control arm to frame bolt torque specs? - Impala ...
Nov 2, 2019
Front End Rebuild - Torque specs??? ' Chevy Impala SS Forum
Nov 9, 2009
Balljoint torque ? ' Chevy Impala SS Forum
Aug 18, 2003
More results from www.impalassforum.com

Torque Specifications

Description Nm lb-ft Axle-to-frame bolt 66 49 Axle damper-to-frame bolt 34 25 Brake caliper guide pin bolt 33 24 Differential bearing cap bolt 61 45 Differential housing cover bolt 29 21 Ring gear bolt 122 90 Tie-rod nut 91 67 U-joint spider retainer bolt 19 14 Upper ball joint pinch bolt 48 35

need ingine sice

all vehicles are similar. remove wheel,remove axle nut,remove tie rod ,remove lower ball joint ,pull spindal and rotor back pushing axle thru at same time,use pry bar to pop axle from tranny, reversal to install, push axle into tranny,pull spindal/rotor back install axle end into hole reset lower ball joint ,tie rod end. then most important TORQUE AXLE NUT TO PROPER SPECS if you dont you will ruin the wheel bearing. not fun to do in the driveway and sometimes all these parts are a real pain to remove
even on a hoist with the proper tools so beware and for the love of life dont hammer on the end of the axle

The tie rod end adjusting nut, 54 ft lb or 74 Nm
The tie rod end ball joint nut, 36 ft lb or 49 Nm

Does this include the outer tie rod nut also to be 45lbs foot torque?

CAMBER BOLT ON THE TIE ROD ENDS.YOU NEED A HAYNES REPAIR MANUAL TO GET THE TORQUE SPECS.YOU PROBABLY NEED WHEEL ALIGNMENT WHENEVER YOU REMOVE TIE ROD ENDS OR UPPER AND LOWER BALL JOINTS IT WILL ALTER WHEEL ALIGNMENT.

hope this helps...

Remove in this order: wheel, loosen the 4 lower ball joint set bolts, cotter pin and nut from tie rod, tie rod from ball joint bracket, ball joint from lower control arm, 4 lower ball joint set bolts, ball joint from suspension. Install is reverse but don't tighten the 4 lower ball joint set bolts.

torque is as follows:
ball joint to control arm- 112 ft-lbs
Tie rod nut- 67 ft-lbs
lower ball joint set bolts- 83 ft-lbs
remember to use a new cotter pin