Question about Hyundai Cars & Trucks

1 Answer

Do I need power to test the driver's door trunk lid switch on a 2010 hyundai genesis sedan? mine is stuck and I have the part removed from the door panel and it is still not moving at all.

I have the interior panel off already, and I have removed the switch assembly from the panel. My question is do I need power to test the switch or is it mechanical? there is a little motherboard-type thing in teh back of the assembly that appears to activate the actuator that opens the trunk or the fuel filler door depending on whether you push the fuel door button or pull the trunk lever. My problem is that I cannot pull the trunk lever to open the trunk, and now that it is removed it still does not move. So mu question is do I need power to try to move the lever or is it mechanical?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Hyundai Master
  • 2,005 Answers

No power is not needed if the switch does not move replace it it is broken

Posted on Mar 17, 2018

Testimonial: "Thanks I will try to replace it!"

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Anonymous

  • 82 Answers

SOURCE: driver side power window stopped working

The door panel is held on by plastic clips and 5 screws. 3 screws are on the bottom and 1 in the pull cup and 1 in the inner door handle.Then grab one of the corners and give a small tug, when you get some of the clips to pop out then proceed around the whole panel. To replace the panel take the clips out of the door with a fork and slide them back into the panel and then line it up on the door and use your hand like a hammer and bang the panel back on. Hope this helps

Posted on Jan 12, 2009

super_guy

  • 1986 Answers

SOURCE: door panel removal for 2002 9-5 on driver rear

On the inside trim, you can remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then you'll need to manipulate the panel and disconnect the door handle linkage from the door handle and disconnect the wiring for your controls

Posted on Sep 23, 2009

Ralph Johnson

  • 645 Answers

SOURCE: how do i remove a drivers side door panel for an

the arm rest that put your arm on should have some screws holding it. sometimes they have little roound or square caps covering the screw wholes you can pop these off to access the screws.

Posted on Feb 09, 2010

eKuyateh

  • 2 Answers

SOURCE: power window won't operate

I tried to power lock the windows won't work what can I change?

Posted on Jan 19, 2011

charleshucke

Charles Huckeba

  • 1114 Answers

SOURCE: 2004 Sebring sedan. drivers side

Most of the time when an issue such as this occurs, the electric motor that operates the window is just stuck, and will need to be gently tapped with a screwdriver, or the wooden end of a hammer. The first thing to do, would be to unplug the switch, and replug it, sometimes it can simply be a bad connection. Try this with the door switch and the electric motor. If that does not work, then try tapping the motor while you, or someone else is operating the switch that will raise the window.

Posted on Mar 18, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I cab't open the trunk on my 2009 hyundai genesis


Take the rear of the back seat out and get into the boot and release the boot lid

Apr 08, 2017 | 2009 Hyundai Genesis

3 Answers

2008 CTS trunk won't unlock


Hi Jeff,
I was going to say, check fuse/ jump the load side of relay Good post.
trunk 1-a4vvaacye2kqxo12bveg1ioe-1-0.jpg

trunk 2-a4vvaacye2kqxo12bveg1ioe-1-2.jpg

Mar 19, 2017 | Cars & Trucks

1 Answer

My remote is bad and the button on the door of my 2008 saturn aura xr will not open the trunk


How about a key ?

Luggage Compartment Description and Operation (Sedan)
Rear Compartment Lid Release
The rear compartment lid can be released in one of three ways:
• Inserting the key into the key lock cylinder, if equipped
• Operating the rear compartment lid release switch
• Using the keyless entry fob
To operate rear compartment lid with the rear compartment lid release switch or with the rear compartment release button on the key fob, the gear selector may be in any position, but vehicle speed must equal 0 for the rear compartment lid to release.
When the rear compartment lid release switch is pushed, the rear compartment lid release signal circuit to the body control module (BCM) is grounded. BCM then grounds the coil side of the trunk release relay through the trunk release relay control circuit. With this voltage is applied to the rear compartment lid release actuator, opening the rear compartment.

do you know how to do electrical testing ?

Circuit/System Verification
Ignition ON, observe the scan tool Trunk Release Switch parameter while pressing and releasing the rear compartment lid release switch. The parameter should change between Active and Inactive.
? If the parameter does not change, refer to Trunk Release Switch Malfunction.
Command the trunk release with a scan tool, the rear compartment lid latch should release the trunk lid.
? If the rear compartment lid latch does not release, refer to Rear Compartment Lid Latch Malfunction

You may want to take it to a repair shop .

Mar 13, 2017 | Saturn Cars & Trucks

1 Answer

Trunk remove from Hyundai? Can a 2007 Hyundai trunk lid fit 2010 Hyundai


Visit the on-line store, know as reliable-store, they have the repair manuals. I'm sure you will get the solution of your problem.
Best Manuals

Dec 17, 2016 | Hyundai Cars & Trucks

1 Answer

How to find trunk latch light switch


The trunk using the key or using the inside trunk release -- located next to the driver's seat. Inspect the left edge of the trunk wall to find the trunk light lens.

Check the switch (located on the trunk lid) that contacts the pull-down mechanism for power. If there is no power, the wiring is "open" between the body and the trunk lid. Look for the problem in the wiring and repair the wires. If there is power, the switch is bad.
Autel MaxiDAS DS708 Multi language Diagnostic tool

Sep 17, 2014 | 2005 Hyundai Accent

1 Answer

How do you remove/ replace trunk lid on a 2013 Genesis sedan ?


the hinges on all cars , unscrew. (impact guns work only)

Jun 24, 2014 | 2007 Suzuki Forenza Sedan

1 Answer

Engine light on 2012 hyundai genesis sedan


I did a quick Google search and found P0128 may indicate a stuck thermostat. The engine is not warming up properly. There are other causes: A code P0128 may mean that one or more of the following has happened:
* Low engine coolant level
* Leaking or stuck open thermostat
* Faulty cooling fan (running too much)
* Faulty coolant temperature (ECT) sensor
* Faulty intake air temperature (IAT) sensor
I got most this info from another thread on Fixya. I hope that it helps you.

Mar 29, 2014 | 2012 Hyundai Genesis 3.8 Sedan 3.8L V6...

1 Answer

2006 jetta sedan trunk light not coming on power to and from light assume poor ground where is switch?


some are on the hinge assembly of the trunklid others, like mine use a mercury switch under the bulb itself that comes on when the lid angle changes..

Feb 02, 2014 | Volkswagen Jetta Cars & Trucks

2 Answers

Bentley Boot lid manual release


This is all the Bentley shows:

doorlockswitch1.gif
Location: Driver's side door trim in storage compartment.

Removing:

- Remove driver's side door trim:
Repair Manual, Body Interior, Repair Group 70 - Unplug connectors.


doorlockswitch2.gif
Carefully disengage catches -arrows-.
- Press switch for interior monitoring and towing protection -1- or trunk release switch -2- out of trim toward rear.

Installing

Installation is carried out in the reverse order.


doorlockswitch3.gif
Remove trunk lid lock.

Repair Manual, Body Exterior, Repair Group 55
- Use a flat screwdriver to pry plastic tab -3- off retaining pins -1-.
- Bend plastic tab fully to rear.
- Pull contact switch -2- first sideways and then up and out of trunk lid lock.

Installing

Install in reverse order, paying attention to the following:

Note:

Make sure that washers are correctly seated between plastic tab and trunk lid lock.

Sep 01, 2012 | Bentley Continental Flying Spur Cars &...

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

41 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

Marvin
Marvin

Level 3 Expert

85219 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...