Which part of the vehicle is the Body Control Module BCMlocated in Mazda Tribute, 2001 model? How can i locate the BCM and replace it in Mazda Tribute 2001 Model?

Question edited for clarity and spelling of 'module'.
Question moved to model category.
No reason given for wanting to know where it is.

What's the ram 1500 bcm location?

Vehicle History https://www.vehiclehistory.com > questions > whats-th...
6 answers
For the 2015 Ram 1500, the BCM (body control module) can be found on the driver's side of the car. It is located in the fuse box. If for any reason the BCM .

More here

https://www.ramforumz.com/threads/body-control-module.277957/

https://www.youtube.com/watch?v=RcjBUdL1ZoA

You probably need a good auto-electrician, but pull out your multimeter and check all the fuses without removing them. On top of each fuse you will see two contacts. Use the probes on those with the meter set to ohms and check for continuity. I wonder if the Body Control Module is faulty though, in which case sell it at auction all clean, polished and detailed.

Fuse 26 is the door locks. 27 is Audio and Interior Lamps

Fuse Box Diagram Mazda Tribute (2001-2007)

https://fuse-box.info > mazda > mazda-tribute-2001-20...
2001-2004: The fuse panel is located below and to the left of the steering wheel by the brake pedal.

...

EE01 is a generic code for a malfunction in the engine control module (ECM). It could be caused by a faulty sensor, wiring issue, or a problem with the ECM itself. It is recommended to have the vehicle scanned for trouble codes to determine the exact cause of the issue.

you found the right place buddy.. i know a lot of websites for repairs and manuals that can really help u..
like reliable-store is pretty good

Body Control Module (BCM) Replacement and Reprogramming
If the BCM is replaced or requires reprogramming, the following procedures must be performed in the specified order:
BCM Setup -- Using a scan tool, go to Vehicle Control Systems » Computer/Integrating Systems » Module Setup » Body Control Module. Select Setup BCM and follow the on-screen instructions, making sure to select the proper RPOs and input the VIN correctly.
BPP Sensor Calibration--Refer to Brake Pedal Position Sensor Calibration
Program Key Fobs--Refer to Transmitter Programming
Setup SDM Part Number in BCM -- Using a scan tool, go to Vehicle Control Systems » Computer/Integrating Systems » Module Setup » Body Control Module. Select Setup SDM Part Number in BCM and follow the on-screen instructions.

Body Control Module (BCM)
Under the I/P below the radio on the right side of the center console.
Do you know what the purpose of the BCM is ?
The body control module (BCM) has a bussed electrical center integrated into the housing. Body control relays and fuses are installed directly on the BCM, which simplifies wiring and junction blocks on the vehicle. The body control system consists of the BCM and its associated controls. Battery positive voltage is provided to the BCM from IBCM BATT 1 fuse and the IBCM BATT 2 fuse in the underhood fuse block. The module grounds are wired to ground G201, G203 and G305. The BCM is wired to the GMLAN High speed serial data buss, and the GMLAN Low speed serial data buss, as well as discrete input and output terminals to control the functions of the vehicle's body.
Serial Data Gateway
The body control module (BCM) in this vehicle functions as a translator between the High and Low speed GMLAN busses. The 2 communication protocols use the BCM to translate communicated serial data messages between the control modules over the 2 serial data busses.
Power Mode Master
This vehicles body control module (BCM) functions as the power mode master (PMM). Refer to Power Mode Description and Operation for a complete description of power mode functions.
Serial Data Power Mode Master
On vehicles that have several control modules connected by serial data circuits, one module is the power mode master (PMM). On this vehicle, the PMM is the body control module (BCM). The PMM receives 3 discrete ignition switch signals to differentiate which power mode will be sent over the Serial Data circuits. The 3-wire Ignition Switch table below illustrates the state of these inputs in correspondence to the ignition switch position:
Relay Controlled Power Mode
The body control module (BCM) uses the discrete ignition switch inputs Off/Run/Crank, Accessory, and ignition 1, to distinguish the correct power mode. The ignition 1 circuit is also routed to the Run/Crank relay for relay controlled power feeds during the appropriate power mode. The BCM, after determining the desired power mode, will activate the appropriate relays for that power mode.
Reprogram the body control module (BCM) after replacement. Refer to Control Module References .




Do you

There is no fuse for the anti-theft system ! It receives it's voltage from the BCM . Do you know what a BCM is ? It is a Body control module .
The Passlock?"¢ System is provided in order to prevent vehicle theft if the ignition lock cylinder is forced to rotate or the ignition switch is operated while separated from the ignition lock cylinder case. If starting is attempted without authorization from the Passlock?"¢ System, the powertrain control module (PCM) will disable engine starting. Start disable may be in the form of fuel disable or starter disable, depending on engine application.
The components of the Passlock?"¢ System are as follows:
?€¢
The ignition lock cylinder and key

?€¢
The ignition lock cylinder case, including the Passlock?"¢ sensor

?€¢
The ignition switch

?€¢
The body control module (BCM)

?€¢
The security indicator on the instrument cluster

?€¢
The powertrain control module (PCM)

The body control module (BCM) contains the logic of the Theft Deterrent System. The BCM provides the battery positive voltage to operate the Passlock?"¢ sensor. The BCM also measures the voltage of the security sensor signal circuit. The voltage measured will indicate whether the Passlock?"¢ sensor has been activated and whether the resistance value from the sensor is a valid value or the tamper value. If voltage measured is in the valid range, the BCM compares this voltage, voltage code, to a previously learned voltage code. If the voltage codes match, the BCM sends a class 2 message containing a password to the powertrain control module (PCM). If the voltage codes do not match, or the voltage is in the tamper range, or there is a circuit fault, the BCM will not send the correct password to the PCM, and the vehicle will not start.
The body control system consists of a BCM and it's associated controls. Battery positive voltage is provided to the BCM from CLSTR fuse in the Fuse Block-left I/P. The module ground is wired to ground G201. The BCM is wired to the Class 2 serial data communication bus as well as discreet input and output terminals to control the functions of the vehicles body !
Now then Karen what problem is your vehicle having , no start an SECURITY light flashing or on solid ?
Now then

AutoPartWarehouse $ 106.37

http://www.autopartswarehouse.com/models/mazda~tribute~makemodel.html

In case of a problem or clarification or my solution was insufficient, don't hesitate to post me a reply.

If you are satisfied, rate my solution with the "thumbs" or (even better) add a testimonial.

Check your EGR valve, check your PCV valve, check your mass airflow sensor and throttle body sensor.

the problem is probably an idle air control valve. its a cheap fix. the body is ford the motor is mazda.
Luke