2000 Mitsubishi Galant Engine Repair Manual

Question edited for clarity and typo 'glant'.
Question moved to model category.

It looks like it is inside the fuel tank and is 140 bucks!

https://www.google.com/search?q=2000+mitsubishi+galant+ftp+sensor+location

Videos to fix the P0450 code

https://www.google.com/search?q=2000+mitsubishi+galant+P0450

..

Some fixya user told me a website reliable-store it is very good.. I used it to repair my shredder it had some spark issue which wasn't easily fixed. you can go there and try

Your 1999 Mitsubishi Diamante is a 3.5L MFI SOHC 6cyl engine.
MFI = multi-port fuel injection
SOHC = single overhead camshaft
This answer covers Mitsubishi Diamante1.8L, 2.4L, 3.0L (SOHC and DOHC), 3.5L, and 1997-2000 1.5L Engines.

2.4L engine shown, others similar.

Fig.1 - CKP position and its two mounting bolts


In Fig. 1, the two arrows point to the CKP (crankshaft position sensor) mounting bolts to remove. 2.4L engine shown.

Fig.2 - CKP reluctor removal

Remove the sensor and slide the reluctor wheel off of the crankshaft-2.4L engine shown.

1. Disconnect the negative battery cable.
2. Remove the timing belt.
3. Unplug the sensor connector.
4. Unfasten the two retaining bolts, then remove the CKP sensor from the vehicle.
5. Installation is the reverse of the removal procedure.

Reference: Autozone online repair guide: Mitsubishi Galant/Mirage/Diamante 1990-2000, at
www.autozone.com

Fig.3 - photo - new 99Diamante CKP, a Wells part #SU4313

Mitsubishi Repair: Problems, Cost and Maintenance

repairpal.com/mitsubishi

A guide to problems, costs, maintenance and repair for your Mitsubishi. Problems ... 2003 Mitsubishi Galant. 2 answers ... my 2006 ME does not change speed, somebody could please help? ... I was told by Pepboys 6. 2000 Mitsubishi Galant.Missing: pcm

Mitsubishi Galant Repair: Problems, Cost and Maintenance

repairpal.com > Cars > Mitsubishi

Learn about common Mitsubishi Galant problems, recalls and typical maintenance and ... A guide to problems, costs, maintenance and repair for your Mitsubishi Galant ...2000 Mitsubishi Galant ... Dealers will inspect the cooler pipe and replace it if anti-corrosion properties are found to be insufficient. ... It's a 6 cylinder.

I think you should buy repair manual first for your vehicle after that it will be easy for you to solve the problem. Check the link may be you will get something useful here Complete 2001 Mitsubishi Galant Workshop Repair Service Manual

I have a 4 cyl engine in my galant and the thermostat is found by following the LOWER radiator hose. You will need to remove the battery in order to gain access to the thermostat housing mounting bolts. There is a video on Youtube.com showing the removal and replacement of the thermostat and radiator for a 1999 mitsubishi galant.

http://youtu.be/Er1szRKrk7c

Infomration on galants in general can be found under the 7g section of http://www.thegalantcenter.net

Are you in USA? I ask because the 94 Galant in the USA came with a 2.4l engine

1. Raise the front of your Mitsubishi Galant with a jack and lower onto jack stands, or use wheel ramps. Disconnect the negative cable from the battery. Drain the coolant into a suitable container by opening the drain plug on the bottom of the radiator.
2. Step 2 Follow the upper radiator hose to where it meets the engine at the thermostat housing. Loosen the clamp at the engine end of the radiator hose and pull the hose off the thermostat housing.
3. Step 3 Remove the two bolts on the thermostat housing cover and pull off the cover. Note the position of the old thermostat and remove it from the thermostat housing. Place a rag in the thermostat housing and scrape any gasket residue from the inside of the thermostat housing cover.
4. Step 4 Take out the rag and insert the new thermostat in the same position as the old one, with the spring-side facing into the engine. Install the new gasket or o-ring, depending on the type of thermostat you are installing. Note that most late 1980s and early 1990s Galant models use a thermostat gasket.
5. Step 5 Replace the thermostat housing cover and tighten the bolts. Re-attach the radiator hose and tighten the clamp. Fill the radiator with new coolant, or use the coolant drained from your Galant earlier if it's relatively new and clean.
6. Step 6 Start your Mitsubishi Galant and run with the heater on high until it reaches operating temperature. Make sure the heater is blowing warm air to ensure the thermostat is working properly. Check for leaks and tighten the radiator hose clamps if you detect any.

Waterpump replacement requires removal and replacement of your timing belt. Because of this it is not your typical do it yourself repair. Engine timing is critical, and not having your belt set correctly can lead to catastrophic engine damage.

You can purchase a service manual at your local parts store to get an idea of what is involved, however this being an interference engine you should leave this job to a professional if you are uncertain enough about your abilities that you need to ask for help on it. The cost to replace the waterpump is far far less than the cost to repair a engine that had an incorrectly set timing belt.

thermostat that sits between the engine and the radiator. The thermostat in most cars is about 2 inches (5 cm) in diameter.


It looks like this:

http://www.trustmymechanic.com/parts_gallery/thermostat.jpg