Question about Acura RDX

Open Question

My keyless key will not lock/unlock or start my 2014 RDX.

When I push lock, a red light flashes on my key fob. Is there a place in the car I can put the key so the car recognizes the key without a battery?

Posted by on

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Anonymous

  • 54 Answers

SOURCE: clio

the key has lost its code. open the doors manually and use the central locking button inside the car. hold it down and keep pressing your key fob. this should re code the key

Posted on Jul 12, 2008

Ad

Anonymous

  • 5 Answers

SOURCE: Immobiliser light flashing and car

Hello, do you know what the locksmith did to get the code on your key? Did anything else flash on the screen when the car would not start. My car is doing the same thing, and my Jaguar dealer is 200 miles away. My screen is showing [Engine Fault, Transmission Fault and DSC Fault]. Any help would be greatly appreciated..

Posted on Sep 14, 2008

onyeredson

Paul W

  • 404 Answers

SOURCE: mercedes 1999 c200 key fob

Hello Haq!
Could it be the key just needs re-coding? maybe you are worrying to much as £177 would be about right as that would need coding etc., Try phoning your local Merc dealer or take the key and V5 to them for coding (Hopefully)
Good Luck!
Paul 'W'
Onyer~EDson(:0)~[><

Posted on Jan 06, 2009

rockitman187

Randy Hough

  • 2559 Answers

SOURCE: My key fob remote will not unlock car doors but will start car

Here you go.If you can't read it I can email it to you.
c2293a3.jpg

Posted on Aug 04, 2009

rgbypoet

  • 166 Answers

SOURCE: key fob lights up but doesn't work even with a new battery

I'm more familiar with Range Rovers and Saab's when it comes to key fobs but if you changed the battery you have to re-program the key fob. If you do not have an owner's manual that can take you through the steps you might want to try: push and hold the lock button on the key fob, put it in the driver's side door and turn to lock. With the button still depressed turn back to open, remove the key and release the button. If this doesn't work check any and all fuses associated with your system and last but not least you could take it to a dealer. Good luck!

Posted on Aug 25, 2009

Testimonial: "thanks ill try what you've suggested"

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I have a 2007 ES 350. Changed key fob battery,now nothing works. Only immobilizer security light is flashing and engine start stop button has amber colored light on


Be sure to use the correct battery, properly in place, clean the key contacts , See owner's manual for additional information.
There are specialized locksmiths for car keys

Oct 02, 2014 | 2007 Lexus ES 350

1 Answer

Mazda mx3 japanese import 94 reg key fob died, i changed the battery but it will not now unlock the car, the doors are deadlocked so the key wont unlock the doors either, can i re-sync it from outside? Or...


Whether your key fob is damaged or just has a dying battery, there is a way for you to unlock your vehicle and start the car. Just follow the steps below:
  1. Press and hold the auxiliary key release button on the underside of the key fob.
  2. Grab the looped end at the top of your key fob.
  3. Pull out the auxiliary key.
  4. Use the auxiliary key to unlock the driver's side door.
[Read more: What to do when you're locked out of your car]

HOW TO START THE MAZDA 3 WITH A BROKEN OR DEAD KEY

Now that you've managed to enter the vehicle with the auxiliary key, you're going to need to know how to start your Mazda 3. At this point, the auxiliary key can be put back into the key fob, as the key fob can still be used to start your vehicle. This will only take a few extra steps.
  1. Make sure the shifter is in the Park (P) or Neutral (N) position.
  2. Depress the brake pedal.
  3. The light on the engine start button should flash green.
  4. Take your key fob and touch the back of it to the push button start.
  5. When the green light on the engine start button stops flashing and remains continuously illuminated, press the push button start normally to start the engine.
  6. It is recommended you allow the vehicle to idle for about 10 seconds.

Mar 03, 2018 | Mazda Cars & Trucks

1 Answer

Keyless entry remote wont progam


It will not unlock the door the first time you push the button. This only registers the key fob ID into the computer. When you press the button on the key fob, press it only once and wait for the hazzard lights to flash twice again. Then open the driver's door. The key fob will not become active until you open the driver's door.

If your hazzard lights do not flash after you press the button on the key fob, there is most likely a problem with the key fob. Either it is not the correct key fob for your vehicle, or the battery is not in correctly or the key fob is defective.

The only other advice I can give you is to have it programmed with a scan tool. This way, the scan tool can verify that the computer in your vehicle is receiving the signal from the key fob.

It can be done either way, but if the "no scanner" way does not work, the rest of the system should be checked for possible problems.

Dec 12, 2011 | 2005 Nissan Altima

1 Answer

RS Focus registered yesterday 19th March Keyless entry but remote fobs do not lock or unlock car. The car was driven back yesterday hav ing now covered 114 miles alarm was going off last night but thats...


should not be using fob buttons for entry or locking for emergency only .if keyless entry walk up to car with fob do not press any buttons see if door opens then walk away from car with fob about 20m then go back to car without fob and see if door locked if so all working fine .indicators will not flash if the above dont work take back to main dealer for diagnostics keys may need to be reprogrammed

Mar 20, 2010 | 2009 Ford Focus

2 Answers

How To Program Porsche 911 Remote Keyless Alarm Key Fob


I have the same problem with my 1995 Porsche 911. I was quoted $260 for the key fob and $70 to program it. Sheesh!

Apr 07, 2009 | 1999 Porsche 911 Carrera

1 Answer

2008 altima When I place my key in the ignition(keyless entry) a warning shows "no key". I have changed the battery and it still says "no key" please give me an estimate of what you think it is and if it...


Lock your car with the keyless entry.Push it twice.Then walk over to passenger side and un lock with key.Then put key in ignition and start the car..If that dont work lock the doors again with the keyless entry.Push lock twice and then push the unlock twice..that should start your car,Repost if you have no luck to consider different stratigies.

I’m happy to assist further over the phone at https://www.6ya.com/expert/joe_a3369546f8067589

Apr 03, 2009 | 2005 Nissan Altima

4 Answers

Program a remote key for 03 A6


I have an A4 and did this to re-program my key:

1. used the key to start the car...then turned it off
2. put the key in the driver door (door closed)
3. pressed the lock button on the key fob once
4. turned the key to lock the door.

This is basically the steps in the owners manual, but the car must be started with the key first, and the key must be in the door lock before pressing the lock button.

Dec 10, 2008 | 2003 Audi A6

1 Answer

My car is acting crazy!


" turn the key on engine off 8 times. the doors will lock and unlock. push one of the buttons on the key fob and the doors will lock and unlock. do this for each remote that you have. when you are done turn the key off. the door locks will lock and unlock. the remote fob should work after this."
From My SecuriLock..

Sep 05, 2008 | 2006 Ford Taurus

6 Answers

Jeep alarm will not turn off


The ignition security on/off is located at the trunk lock. unlock and lock rear gate and the alarm will turn off. My jeep sat in my drive for a month before a jeep tech told me this. It still triggers the security sometimes when I unlock the passenger door with the key and I go straight to the rear gate lock and it shuts off instantly.

Jun 27, 2008 | 1994 Jeep Grand Cherokee

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

138 people viewed this question

Ask a Question

Usually answered in minutes!

Top Acura Experts

Marvin
Marvin

Level 3 Expert

85219 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Are you an Acura Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...