Question about 2006 Chevrolet Impala

Open Question

Replace rear struts 2006 Chevy Impala - 2006 Chevrolet Impala

Posted by on

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
emissionwiz

Marvin

  • 85216 Answers

SOURCE: How do I program my key for my 2006 Chevy Impala?

Add Duplicate Key (PK3 or PK3+ key)
1. Insert an existing key into the ignition cylinder.
2. Turn the ignition cylinder to ON (RUN) and back to OFF.
3. Remove the existing key and, within fifteen seconds, insert the new key
and turn it to ON (RUN).
4. The security light will light up for two seconds to indicate success in programming
the key into the vehicle.
Originate New Master Key (PK3 or PK3+ key)

1. Insert new key into ignition cylinder and turn it to the ON (RUN) position.
The security light on the dash will illuminate and stay on for ten minutes.
2. When the security light goes out, you have one minute to start the next
step. Turn the ignition cylinder to OFF and then back to the ON (RUN)
position. The security light on the dash will illuminate and stay on for ten
more minutes.
3. When the security light goes out, you have one minute to start the next
step. Turn the ignition cylinder to OFF and then back on the ON (RUN)
position. The security light on the dash will illuminate and stay on for ten
more minutes.
4. After the security light has gone off the third time, the key has been programmed
into the vehicle’s computer and will operate the car. It has replaced ALL the
previous electronic key codes and is the ONLY key programmed into the
vehicle’s computer.

Add Duplicate Key (PK3 or PK3+ key)

1. Insert an existing key into the ignition cylinder.
2. Turn the ignition cylinder to ON (RUN) and back to OFF.
3. Remove the existing key and, within fifteen seconds, insert the new key
and turn it to ON (RUN).
4. The security light will light up for two seconds to indicate success in programming
the key into the vehicle.

Posted on May 20, 2009

Ad
abauto

Travis Mcilree

  • 353 Answers

SOURCE: ihow do you replace rear struts on a 1999 ford

Suspension Strut: Service and Repair
Removal and Installation
REMOVAL
1. Remove the package tray trim panel.
2. Remove the upper strut and spring assembly nuts.
3. Raise and support the vehicle.
4. Slide the brake hose clip off and position the brake hose aside.
5. If equipped with anti-lock brakes, remove the Anti-Lock Brake System (ABS) sensor bracket bolt.
6. Remove the lower strut and spring assembly bolts and the strut and spring assembly.
INSTALLATION
1. To install, reverse the removal procedure.

Posted on Sep 11, 2009

Anonymous

  • 347 Answers

SOURCE: 2005 impala. Rear window defroster is not working

they have a fuse and a rely make sure the wire end is on the conector on the window

Posted on Oct 02, 2009

motor1258

Mike Butler

  • 6674 Answers

SOURCE: 2006 Chevy Impala reduced engine power

best bet is to stop in at a Pep Boys, Autozone, or similar big autoparts seller, and ask for free trouble code scan, which should pinpoint area causing problem. If not obvious by codes, what is necessary to repair the problem code, get back to us with those codes and we will be glad to assist you further. Better this way, takes away the guess work, and saves you money, as well as getting it right the first time.

Posted on Dec 12, 2009

Kolawole Ayede

  • 327 Answers

SOURCE: replace rear brake pads 2006 Chevy Impala

Hello, to replace the rear brake pads follow the following steps:

1. Lift the Chevy Impala with the jack and place it on jack stands.
2. Remove the wheels with a lug-nut wrench and set them aside. The lug-nut wrench can be found in the trunk of your Chevy Impala.
3. Remove the caliper with a ratchet and use a bungee cord to hang the caliper. Do not let the caliper hang from the brake hose, as the hose might break and cause fluid to leak.

4. Remove the brake caliper bracket from the steering knuckle with a ratchet. Set it aside.

5. Remove the break rotor from the hub. The rotor might require force to be removed; if it does, use a hammer to hit the rotor in the center, where the lug studs are located. Take care not to hit the studs.

6. Remove the new rotor from its packaging and use brake cleaner to remove the grease from the rotor. Grease is applied on the rotor in the factory to inhibit rust during storage.

7. Install the new rotor onto the hub.

8. Install the caliper bracket with new brake pads onto the rotor and fasten it to the steering knuckle. Use a ratchet to tighten the bolts.
9. Open the master cylinder reservoir so you don't break a seal while compressing the brake caliper.

10. Compress the brake caliper with a C-clamp, so that the caliper can fit over the new brake pads. Install the caliper by securing it to the brake caliper bracket with a ratchet.

Thanks


























Posted on Jul 19, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Directions on changing out the TCM in an chevy impala 2006


Try watching the educational videos on YouTube.com :
chevy impala 2006 , replace the TCM

I hope this helps you out!

Mar 31, 2017 | 2006 Chevrolet Impala

2 Answers

What size allen needed to remove break pads


Allen wrenches usually come in a set, try 3/8.

Apr 30, 2016 | 2008 Chevrolet Chevrolet Impala LS

2 Answers

WHAT IF ANY SPECIAL TOOLS ARE NEEDED TO REPLACE A REAR WHEEL BEARING ?


No.
The most you'll need is a big hammer or a air hammer to loosen the bearing from the spindle but just like changing a front bearing

Jul 14, 2014 | 2006 Chevrolet Impala

2 Answers

Rear strut assembly 17 inch wheels


What part of the suspension is bad?

Apr 20, 2014 | 2006 Pontiac Grand Prix

1 Answer

On my chevy 2006 impala the rear tire momitor sensors are not working all the time . Should I replace them.


you only need to replace what is bad it has to be tested with a tpms scanner, and you only need to replace the one, some just need to be calibrated after replacing. let me know what happens

Mar 23, 2010 | 2006 Chevrolet Impala

2 Answers

Were is the crank sensor located at on 2006 impala


Usually ,& depending on engine, is located on the rear side of the engine block behindthe crankshaft balancer. Good luck!

Nov 26, 2009 | 2006 Chevrolet Impala

1 Answer

Steeing wheel vibrates when i turn to the left from a stop


Does it feel like it's trying to pull back straight? if so, I would say you have a seized strut bearing on the right side.

Jun 02, 2009 | 2006 Chevrolet Impala

2 Answers

I want to know if my 2003 Chevy Impala has shocks and struts


shocks and struts are basically the same thing. i believe struts offer more structeral support to your vehicle too. i'd suggest www.rockauto.com or www.autozone.com to confirm what parts are needed

Robert

Feb 27, 2009 | 2003 Chevrolet Impala

Not finding what you are looking for?
2006 Chevrolet Impala Logo

Related Topics:

153 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

Marvin
Marvin

Level 3 Expert

85216 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...