SOURCE: BMW 328i Starter how to replaice
1999 BMW 328I 2.8L EFI DOHC 6cyl
Starter - Removal & Installation
The
starter motor on some models is very difficult to see from the top of
engine compartment as it is covered by the intake manifold. On these
models, without removing the intake manifold, the starter motor must be
removed from underneath the vehicle. Because the starter motor mounting
bolts are not easy to access, a long extension with a universal joint
mounted on a proper sized socket could be used. A three foot
transmission extension is commercially available from tool vendors that
has a 3
/
8
inch drive of the driven end and
1
/
2
inch drive on the drive end. If used with a non-binding impact
universal joint and a proper fitting impact socket, the starter motor
fasteners can be removed from underneath the vehicle.
Once the starter motor fasteners are removed, the
starter motor may have to be moved side-to-side several times to loosen
the dowel pin if it has corroded in place.
NOTE
When the battery is disconnected, the radio code, on-board
computer and clock settings will be lost. The radio code should be
obtained before disconnecting the battery or radio. Once the battery
has been reconnected, the radio will not function unless the code is
keyed in.
Starter motor electrical terminal fastener torque specifications for all models:
M5 terminal fasteners: 44 inch lbs. (5 Nm)
M6 terminal fasteners: 53 inch lbs. (6 Nm)
M8 terminal fasteners: 115 inch lbs. (13 Nm)
Starter motor mounting fasteners:
Hex head bolts: 36 ft. lbs. (49 Nm)
Torx bolts: 32 ft. lbs. (43 Nm)
Starter motor electrical terminal fastener torque specifications for all models:
M5 terminal fasteners: 44 inch lbs. (5 Nm)
M6 terminal fasteners: 53 inch lbs. (6 Nm)
M8 terminal fasteners: 115 inch lbs. (13 Nm)
Starter motor mounting fasteners:
Hex head bolts: 36 ft. lbs. (49 Nm)
Torx bolts: 32 ft. lbs. (43 Nm)
E36 6-Cylinder Engines
Automatic Transmission Models
Manual Transmission Models
Fig. A view of the starter motor mounting fasteners and dowel pin. The mounting bolts are threaded into the starter motor
Fig. The starter motor mounting bolts are a different size than the transmission-to-engine mounting bolts
I hope help you with this (rated this help) Good luck.
SOURCE: removal and replament of a 3 Series BMW E46 1998 saloon wing mirr
On the inside trim, you can remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then you'll need to manipulate the panel and disconnect the door handle linkage from the door handle and disconnect the wiring for your controls. Then you can access the bolts that secure the mirror onto the door
SOURCE: replacing fuse for cd changer on bmw 3 series
If you turn radio on then mode it should display cd,if not there is no connection, either power or ubi cable.The only fuse is on the back of the changer.You have to remove to access.I don`t know your problem but if your cartridge will not eject, hold eject button and insert credit card under cartridge push fully in and move left to right this will locate micro switch.
SOURCE: how can i remove door handle of bmw X-3
If you have the door panel off already. you have to look at the back of the door latch mechanism. you will see where the wire for the door handle hooks to the door. If you are starting you have to be very careful in removing the screws for the door panel look for the hidden screws under caps with cutout.there should be a toric screw where the door handle is and another one close to where the mirror mounts. again look for caps
686 views
Usually answered in minutes!
×