Question about 1999 Isuzu Rodeo

Open Question

1999 rodeo Isuzu hoses

Need picture of cooling system hoses from under the intake manifold that shows names parts with instructions to replace

Posted by on

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Anonymous

  • 3 Answers

SOURCE: power windows isuzu rodeo 1999

Cable must of disconnected need to take door cover off and reconnect...

Posted on Jan 10, 2009

Ad

Anonymous

  • 386 Answers

SOURCE: HOW TO REPLACE INTAKE MANIFOLD ON A LINCOLN

answer , very carefully ...

drain coolant , remove and mark all vacuum lines , make a schematic to diagram your hose routing, disconnect and plug all fuel lines, remove distributor and mark location of rotor, disconnect battery, remove any necessary cables, brackets and or accesseries, remove intake mounting bolts, note length of bolts and reference location, pry up on intake , remove intake, scrape old gasket off , must be very clean to reinstall new gasket or you will cause a leak..

Posted on Nov 02, 2009

carsandcomps

Brandon Bruce

  • 722 Answers

SOURCE: need torque specs for isuzu rodeo 3.2 intake

josephrloop,

Go to: http://www.autozone.com/autozone/ymme/ymmeYear.jsp?_requestid=552857

Here you can select the year, make and model.

I hope this information proves useful and helps you with your intake torque success.

Cordially,

carsandcomps
Guru @ Fixya

Posted on Apr 10, 2010

honeymokey

honeymokey

  • 3113 Answers

SOURCE: 1999 Rodeo,, Isuzu, starter motor and solenoid

Follow positive wire to starter that has the solenid on it.

Posted on Aug 10, 2010

stevenhurc

Steve Hurc

  • 459 Answers

SOURCE: I need to replace the thermostat for my 2000 Isuzu

remove fuel pump fuse and start car when it dies try to start again, no more spluttering just cranking, the fuel system is now depressurised. you can now disconnect both of the quick disconnect fuel lines at rear lower section of inlet manifold this is hard to get to some access this by removing the EGR valve so you can get your arms down there watch out for sharp edges of manifold. you dont need to take the top section of the inlet manifold off but will need new lower inlet manifold gaskets to haed.once manifold is off block all intake ports with rag or put tape over ports to stop dirt and stuff falling into ports while continuing to work on the coolant pipes below to get to thermostat.undo only 4 long centre bolts and the 4 nuts, one in each corner(no.3 in picture).

stevenhurc_7.jpgyou dont need to remove throttle body but some people do.

Posted on Feb 24, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Bad theromostat 3.2 isuzu how to


The thermostat on the 2001 Isuzu Rodeo 3.2L v6 is located on the top of the engine under the upper intake manifold. In order to replace it you will have to depressurize the fuel system by running the engine with the fuel pump fuze removed until the engine dies and then carefully remove the fuel rail and injectors. Then remove the intake manifold which will give you access to the coolant nozzle fixture attached to the top of the engine. The thermostat is in the top of the engine block under the nozzle fixture. Be sure to replace the thermostat with the proper replacement part (may be difficult to find) and put on new gaskets for the intake manifold before replacing it.

Apr 11, 2013 | 2001 Isuzu Rodeo

1 Answer

Water leak under intake


Your hose clamp may just need tighten,or your clamp is bad and replace.

Aug 25, 2012 | 1994 Isuzu Rodeo

1 Answer

Instructions to replace thermostat in 1999 isuzu amigo v6


if you have the 3.5 v6 izuzu engine the thermostat is a major job, requires removing upper intake ,because it is under not in front of like most thermostats.
about 3-4 hour job depending what kind of problems you run into.

Feb 16, 2012 | 1999 Isuzu Rodeo

1 Answer

I need to replace the thermostat for my 2000 Isuzu Rodeo, V6 3.2 Liter LS model? I see that it is on top of the engine under the intake. What steps do I take to remove the intake. Will the top and bottom...


remove fuel pump fuse and start car when it dies try to start again, no more spluttering just cranking, the fuel system is now depressurised. you can now disconnect both of the quick disconnect fuel lines at rear lower section of inlet manifold this is hard to get to some access this by removing the EGR valve so you can get your arms down there watch out for sharp edges of manifold. you dont need to take the top section of the inlet manifold off but will need new lower inlet manifold gaskets to haed.once manifold is off block all intake ports with rag or put tape over ports to stop dirt and stuff falling into ports while continuing to work on the coolant pipes below to get to thermostat.undo only 4 long centre bolts and the 4 nuts, one in each corner(no.3 in picture).

stevenhurc_7.jpgyou dont need to remove throttle body but some people do.

Feb 21, 2011 | 2000 Isuzu Rodeo

1 Answer

Where is the nock senseser?? On a 99 Isuzu rodeo V6


If it is a v6 then they should be in the valley between to two heads and under the intake manifold. if it is a four cyl. check high on the block on the intake side.

Aug 19, 2010 | 1999 Isuzu Rodeo

2 Answers

Where is the crank sensor located at on 1999 isuzu rodeo?


Where Is The Camshaft Position Sensor Located On A 1999 Isuzu Rodeo?

Jan 10, 2010 | 1999 Isuzu Rodeo

1 Answer

ISUZU WAS IN AN ACCIDENT. THE PLASTIC HEATER HOSE


Strip it back and replace all the broken items/parts. New or good clean used parts. You do it or pay a repair shop. What is the problem or question. It is broken Fix it

Sep 26, 2009 | 1999 Isuzu Rodeo

3 Answers

2000 isuzu rodeo V6 3.2l thermostat replacement


Well, as you said, Isuzu engineers are not the brightest. We are in the process of trying to figure out how the oil got full of water! If anyone has experience in the 3.2 V6 2000 model and where the likely failed spot for the cooling system is, I'm all ears.
To your problem, the thermostat housing is located under the intake manifold, yes under it. You will have to remove the intake and fuel injection system (lots of fun) to get at the hard pipe lines under and in the front of the engine. Once there removal and replacement of the thermostat is easy.

Aug 18, 2008 | 2000 Isuzu Rodeo

Not finding what you are looking for?
1999 Isuzu Rodeo Logo

Related Topics:

44 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

Marvin
Marvin

Level 3 Expert

85222 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

459 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...