Question about 2002 Dodge Intrepid
After removing any screws for pull handles etc with a pry bat small one pop it loose at bottom and sides then lift it off the side of window opening
Posted on Apr 08, 2019
Posted on Apr 08, 2019
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
Here's a link to this great service
Posted on Jan 02, 2017
1, Disconnect the able from negative terminal of the battery.
2. Pry the courtesy light from the door trim and disconnect the wire connector..
3. Remove all door trim panel retaining screws and door pull armrest assemblies.
4. Remove the door switch panel and the control switch panel and the control switch assembly.
5. On models with memory seats/mirrors, use small-flat bladed pry tool to remove and disconnect the wire.
6. Grasp the trim panel lift up and pull out to detach it from the door. Disconnect the inner door handle lock rod from the handle. Unplug any electrical connectors remaining and remove the door panel.
7. To install, connect the wire harness connectors and place the panel in position in the door. Press the trim panel down into place until the hooks are seated.
8. Install the armrest/door pulls, the courtesy light and the window switch'
9. Reconnect the battery
Also. You will need star pattern drivers to remove the window and motor from your door. If you have all the equipment it should only take you 1 hour.
Posted on Jan 15, 2009
SOURCE: remove door panel
Disconnect your negative battery cable. Locate and remove the screws
that hold your interior door handles in place (they may be hidden by
snap in, or snap on clips). Remove the interior door handles, then
disconnect the wire clips to the switches. Your panel is held in place
by snap in clips; use a small pry bar to pull them from the door (try
to get as close to, or directly under the clips to prevent them from
tearing out of the door panel). Once the clips are pulled, pull the
panel upward to remove it from the door.
Install in reverse.
Posted on May 25, 2009
SOURCE: replacing passenger side mirror
no the door pannel does not need to come off but there is a triangle shaped plastic trim pannel above the door pannel that needs to be removed to access the mounting bolts.
Posted on May 28, 2009
SOURCE: Door panel removal
You'll need to remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. If needed, you can pull back the weather seal (can't reuse it, but it's not that important) and you will be able to access everything inside the door
Posted on Aug 14, 2009
On the inside trim, you can remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then you'll need to manipulate the panel and disconnect the door handle linkage from the door handle and disconnect the wiring for your controls
Posted on Sep 23, 2009
Tips for a great answer:
Nov 13, 2014 | 1999 Dodge Intrepid
Oct 26, 2011 | 2002 Dodge Intrepid
Aug 27, 2011 | 1997 Dodge Intrepid
Oct 07, 2009 | 2002 Dodge Intrepid
May 29, 2009 | 2004 Dodge Intrepid
May 24, 2009 | 1997 Dodge Intrepid
Feb 21, 2009 | 1999 Dodge Intrepid
Dec 26, 2008 | 1999 Dodge Intrepid
Sep 03, 2008 | 2002 Dodge Intrepid
31 people viewed this question
Usually answered in minutes!