Question about Chevrolet Cruze

Open Question

2011 chevy cruze ls 1.8 plastic arm came off intake manifold positioner what hols it on or how to fix. Larry

Posted by on

Ad

2 Suggested Answers

Anonymous

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

john h

  • 22486 Answers

SOURCE: 2011 chevy cruze ls 1.8 8 inch plastic arm came off bottom I think intake manifold valve positioner what holds it on the bottom to keep it from coming off

came off bottom of what and is their any sensors or wiring attached

Posted on Jul 11, 2018

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2011 chevy cruze code po2076


P2076 is Trouble code for the intake manifold tuning valve. You need to check power supply and signal to connectors. Check also the wirings. You can also monitor from the scan tool regarding the value of the position sensor of intake manifold tuning valve and the value commanded by the ecm. Sometimes this valve get stuck and will not respond to ecm controls. ?

Jul 07, 2018 | Chevrolet Cruze Cars & Trucks

1 Answer

Looking for torque settings - 2011 chef cruze 1.6


Are you talking about chevy cruze?
If you want torque specs on everything, get a factory manual. I just checked out ebay, they have a factory service manual for $24.95.
I don't believe this is a paper manual. Maybe a dvd or you access over the internet. If interested, make sure you read everything about this manual. They even have a link where you can contact seller and ask questions.
If you want torque spec for cylinder head or intake manifold, I might be able to find it, not the whole vehicle.

Apr 05, 2018 | Chevrolet Cruze Cars & Trucks

1 Answer

Outside temperature on Chevy Cruze


IF IT'S A 2013 TAKE IN IT'S UNDER WARRANTY.

Jan 29, 2014 | 2011 Chevrolet Cruze

1 Answer

2011 chevy cruze engine running doors locked


not on these new cars.. its a child safety thing..may want to get a second key made..

Jan 05, 2014 | 2011 Chevrolet Cruze

1 Answer

2011 chevy cruze wont SHIFT OUT OF PARK, KEY WONT COME OUT, BRAKE LIGHTS DONT WORK.


Where is the relay module 45 and 46 located on my 2011 chevy cruze

Mar 28, 2013 | 2011 Chevrolet Cruze

1 Answer

Where does the cam position sencer located at


It's officially called a CMP Syncronizer.
There are stern warnings on the page associated with this.
CAMSHAFT POSITION (CMP) SENSOR Removal & Installation
CMP sensor is located on rear of engine, behind intake manifold. Before removing, note position of electrical connector on CMP sensor. Remove upper intake manifold. See UPPER INTAKE MANIFOLD . Disconnect CMP sensor. Remove CMP sensor screws and CMP sensor. To install, reverse removal procedure. Ensure CMP sensor electrical connector is pointing in original direction. Tighten CMP sensor to specification.
2 . Failure to use synchro positioner during installation will cause fuel injection to be out of time and may cause engine damage.
CAUTION: DO NOT rotate crankshaft when Synchro Positioner (T95T-12200-A) is positioned on CMP synchronizer. Armature tab will be damaged and synchronizer timing may be shifted. Removal
1. Position crankshaft to TDC of cylinder No. 1, on compression stroke. Note position of electrical connector on CMP sensor. 2. Disconnect negative battery cable. Unplug harness connector from CMP sensor. Remove CMP sensor screws and CMP sensor from positioner. Remove synchronizer hold-down bolt and CMP synchronizer.
Fig. 2: Exploded View Of CMP Synchronizer Assembly (Typical) Courtesy of FORD MOTOR CO.
CAUTION: DO NOT rotate crankshaft while synchronizer is removed from engine. Installation
1. Install Synchro Positioner (T95T-12200-A) on synchronizer housing. See Fig. 3 . Rotate synchronizer shaft until vane on shaft aligns with slot on synchro positioner. Rotate synchro positioner until engaged into notch in housing. Dip drive gear in engine oil.
Fig. 3: Installing Synchro Positioner On Synchronizer Assembly (Typical) Courtesy of FORD MOTOR CO.
Fig. 4: Positioning Synchronizer For Installation Courtesy of FORD MOTOR CO. 2. Rotate sychronizer assembly so that synchro positioner is 60 degrees counterclockwise of crankshaft centerline before inserting synchronizer assembly into engine. See Fig. 4 . 3. As synchronizer is inserted into engine, synchronizer will rotate. When seated, synchronizer electrical connector should be located in original position.
CAUTION: If CMP sensor electrical connector is not positioned correctly, DO NOT reposition connector by rotating synchronizer. This may cause fuel system to be out of time with the engine, causing possible engine damage or an engine misfire. Remove synchronizer and reinstall. See step 3 . 4. Install hold-down clamp and tighten bolt to specification. See TORQUE SPECIFICATIONS . Install CMP sensor to synchronizer and tighten to specification. Ensure CMP sensor electrical connector is in original position. Reconnect wiring to CMP sensor. Connect negative battery cable.
fig2explodedviewofcmpsy.gif

May 03, 2011 | 1995 Ford Explorer

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

29 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

Marvin
Marvin

Level 3 Expert

85223 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...