2013 Dodge Avenger 4 cyl 2.4 liter cylinder 2 misfire order

If you're still experiencing a cylinder 2 misfire in your 2013 Dodge Avenger 3.6L V6 after replacing the coils, spark plugs, and wires, there are a few potential causes to consider: 1. Fuel Injector Issue: A malfunctioning or clogged fuel injector can cause a misfire in a specific cylinder. Check the fuel injector for cylinder 2 and ensure it is functioning properly. It may require cleaning or replacement. 2. Compression Problem: Low compression in cylinder 2 can lead to a misfire. Perform a compression test to check the compression levels in all cylinders. If cylinder 2 shows significantly lower compression, it may indicate issues with the valves, piston rings, or cylinder head gasket. 3. Ignition Timing: Incorrect ignition timing can cause misfires. Ensure the ignition timing is set correctly according to the manufacturer's specifications. 4. Vacuum Leak: A vacuum leak near cylinder 2 can disrupt the air-fuel mixture and lead to a misfire. Inspect the vacuum lines and intake manifold for any leaks or loose connections. 5.Engine Control Module (ECM) Issue: A faulty ECM can incorrectly trigger a misfire code. Consider having the ECM scanned for any error codes or anomalies related to cylinder 2.

See this YouTube video at 6:45 (pause the video there).

Part 2 3 2013 Dodge Avenger 2 4 liter waterpump removal

Visit the on-line store, know as reliable-store, they have the repair manuals. I'm sure you will get the solution of your problem.
Best Manuals

1-4-2-5-3-6

Possible causes:
Faulty spark plug
Clogged or faulty fuel injector
Faulty ignition coil
Fuel injector
Harness is open or shorted
Fuel injector circuit has poor electrical connection
Ignition coil harness is open or shorted
Ignition coil circuit poor electrical connection
Insufficient cylinder compression
Incorrect fuel pressure
Intake air leak

The P0304 code means that the cylinder 4 is misfiring or is randomly misfiring. Start by checking for intake leaks and if no leaks are found the next step is to replace the spark plugs on cylinder 4.

For the 1996 Dodge Avenger:
I do not know if you have the 2.0L DOHC In-Line 4-Cylinder or the 2.5L SOHC V6; howvwere I have included both below...

For the 2.0L DOHC In-Line 4-Cylinder:
Firing Order:
1-3-4-2
Cylinders:
..........(back).........
|...1....2....3....4...|
.........(front)
Ignition Coil:
.....................o <---4
1---> o
.....................O <---Connector
2---> o
.....................o <---3

For the 2.5L SOHC V6:
Firing Order:
1-2-3-4-5-6
Cylinders:
.......(back).......
|...1....3....5...|
.......................
|...2....4....6...|
.......(front)
Distributor:
.......(back)
....(+)....5
..4...........3
2
....6.........1
...........(+)-screw

Let me know if this helped......

THERE ARE 2 ENGINE AVAILIBLE GO TO THE 2 LINKS BELOW FOR THE 2.0 AND 2.5 LITER
2.5 LITER
http://autorepair.about.com/library/firing_orders/bl-fo-5883.htm

2.0 LITER
http://autorepair.about.com/library/firing_orders/bl-fo-5882.htm

Firts time swap spark plug & ignition coil between two different cylinders and read again if the same #2 cyl. misfires !
If #2 cyl. is OK and another cyl. misfires then spark plug or ignition coil is out of order and must be replaced.
If #2 cyl. misfires again then #2 injector must be checked !
If ignition coils & spark plugs (complete set for 6 cyl.) are replaced then you must check #2 injector !

1997 Dodge Avenger
2.0 liter DOHC L4 VIN "Y"



1997 Dodge Avenger
2.5 liter SOHC V-6 VIN "N"

The 4 cyl. and 6 cyl starters are not interchangeable.


---------------------------------------------------------------------------------------