Question about Cars & Trucks

1 Answer

I have a bennche 700 big horn side by side, I have no spark. I replaced the spark plug and the coil. all the fuses are ok. I don"t know what to do next.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Cars & Trucks Master
  • 3,577 Answers

Hey Patrick,,
ouch... sounds like it time for a professional with a factory service manual... you changed the biggie/easy two..

NOW - you would have saved $$ by getting it professionally checked/diagnosed first and replaced what was actually defective!!

Posted on Jun 25, 2019

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Anonymous

  • 1 Answer

SOURCE: 94 toyota camery no spark

I had the same problem recently but replacing the ignition Coil under the distributor (inside) solved the problem. Also replaced the distributor Cap and rotor at the same time.

Posted on Oct 31, 2008

nvannoy

nvannoy

  • 234 Answers

SOURCE: 1993 toyota corolla, problem no spark to spark

Check the ignition relay and all the main relays on the battery.

Posted on Jan 06, 2010

modlara

  • 111 Answers

SOURCE: No spark in '05 Mazda 6

any wires not plugged into there respective places, any sensors the old engine had that this one don't, did you use the old distributor for your coil setup,I think it might be, luck

Posted on Feb 01, 2010

Ed Mac

  • 731 Answers

SOURCE: Horn not working. When depressing

The clicking you hear is the horn relay working.
I would locate the horn and insure the wiring is intact and the horn has a good solid ground.
Then while someone is pressing the horn button measure the voltage at the wire that attaches to the horn to ground. If you get 12v or more the horn is bad. If you don't get any voltage replace the relay

Posted on Jan 23, 2011

clifford224

Clifford Beard

  • 1975 Answers

SOURCE: 94 mustang 3.8 v6 need

Here's a picture for you. I hope this helps and good luck.


clifford224_217.jpg

Posted on May 08, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2017 Bennche Bighorn 500. Does it have a horn?


It must have as it is road ready with lights, speedo, trip meter etc. Even a golf cart has a horn. The full detailed specs are here, but don't mention the horn. Phone a dealer and ask. It is an easy job to install one if you need to.

2016 Bennche Bighorn 500

Mar 23, 2017 | Cars & Trucks

2 Answers

I have a 2003 Saab 9-3 Turbo convertible, I have replaced the coil pack, the battery, starter, fuel pump, crankshaft position sensor, spark plugs & more, the engine cranks like nobodys busines


did you check for voltage at the coil pack low tension input
this comes from the electronic ignition and the distributer dc setting on a multimeter

check inside the distributer that the little magnet is still in place on the rotor and that the sensor is outputing pulses as it turns over
{you can use a meter set to AC range for this ...}
pull a plug out and place its metal to ground check for actual sparks
if this is there then its fuel ...

Dec 05, 2014 | 2003 Saab 9-3

1 Answer

Installing a temporary horn button


IF this is really just temporary, locate the wire going to the horn(s)
Find where you`re going to get the +12V feed, direct from the battery, cigarette lighter, spare hot terminal at fuseblock. any place that`s hot with the key switch off.
Connect one wire of the inline fuse holder to the +12V source you have selected.
If you don`t know for sure that the horn(s) are OK run a wire from the other side of the fuse holder to the horn feed, and connect temporarily, it should honk.
If all is well there run that fused wire to one side of your switch and the other side to the horns.
That`s it.

Dec 04, 2013 | Cars & Trucks

1 Answer

I changed the plugs the wires and rotor big and condenser in my 73 d 100 but I don't have spark to my plugs


Check the points in the distributer also could be bad coil or ignition fuse

Dec 31, 2011 | 1981 Ford F 100

1 Answer

Car won't start even after spraying starter fluid in throutle body. Horn honked while cranking it over two or three times, without touching horn. No spark?


Was the car running ok prior to this no start?Did it start missing or loosed power?
The horn thing is unusual but can be triggered by cars alarm system or ECU fault.
Does car have an alarm?was the battery run flat or changed just prior to this fault?
They both will inhibit spark if alarm locked on or faulty,as for ECU fault.
Depending on the model.They have a coil mounted on the fire wall that does fail.Check for spark at the centre tower with insulated pliers and holding the lead close to a bare metal area of engine area.
Run a test light on +ve side of coil.if it has power to it.it will light.the other side should flash on crank to indicate trigger from distributor.if ok and no output from tower lead,replace coil.
The model described;to access the coil bolts that fall inside panel when loosened,remove the plastic grille below the wipers.
I hope this helps or get back to me with your findings.

Apr 03, 2011 | 1994 Volkswagen Golf

1 Answer

1. my radio just stopped working, it used to go on and off depending on the dots in the road or a big bump but now there is nothing, the fuses are ok too. 2. the horn does not work at all, fuses are ok...


it sounds like the plug in the back of the radio has come loose. remove radio and check connection. as far as the horn PULL THE WIRE FROM THE HORN UNDER THE HOOD THEN RUN A TEST LEAD FROM THE + SIDE OF YOUR BATTERY TO THE HORN IF IT HONKS REPLACE THE HORN RELAY IF NOT REPLACE THE HORN. GOOD LUCK

If you need further help, I’m available over the phone at https://www.6ya.com/expert/michael_00678fd4800d19c5

Feb 15, 2011 | 2006 Ford F-150

2 Answers

I have no spark i replaced the spark plugs spark wires and the coil pack and still nothing my power distribution box is fine any ideas


Crank engine with distributor cap removed, is it turning?
(That is if it has a distributor cap, some newer cars don’t have one)is it turning?
Broken timing belt or chain?

Are you getting power to the + positive side of the coil (small wires) with key on ? Hint; I use a needle pushed into the back of the plug so as not to damage the wiring.
If you have power then wiring from the ignition switch is OK. It usually is.
Hook your test light to the - negative side of the coil (one end on the - terminal and the other end on a ground). You should have power on the - side of the coil with the key on and engine off.
Crank the engine while watching the test light. Get a flashing signal at the test light when cranking?
If so and you have no spark the coil is likely dead. (don’t rely merely on resistance tests for a coil, a weak coil can test ok for resistance but still give no spark. It happens but is unusual. I learned this the hard way!)
No flashing signal?
Check continuity in all primary circuit wiring for opens.
If they are good,
It is time to check the pulse generator in the distributor. (That is if it has a distributor cap, some newer cars don’t have one, if it doesn’t then the ECM or computer sends signal via the crankshaft position sensor and the camshaft position sensor)
With the engine in non-running condition connect your A/C voltmeter to the pair of wires at the pulse generator and crank the engine. You are looking for an A/C signal that makes 4-6 volts of A/C. Got this? If so the ignition module is dead or has a bad ground. If not (more likely) you have a dead pulse generator in the distributor.
If you have three wires in the distributor signal wire you have a Hall effect sensor. I forget how to test that one. (Chrysler stuff)


If this part of the primary ignition tests ok then check wiring to ECM pinouts for opens. Wiring tests ok. ECM as last resort.
Hope this helps...........

Sep 29, 2009 | 1992 Ford Ranger

1 Answer

Jerking bad when driving replaced coil lead plugs ok coil lead sparking outside coil


Is it sparking between boots or is it from the boot to the engine? You need to use dielectric grease on the boot on the coil to stop leakage of voltage between coil towers, I can't find the 2006 laser so chose a model similar to that model. With the engine off and you pull the spark plug wires put a little bit of the special grease on your finger and put it on the inside of the boot of the spark plug wire at the coil and at the spark plug. Be sure to not get any on the spark plug metal tip or on the metal on the coil pack. When removing the spark plug wire from the coil and plug be sure to twist it with the engine being cold so that you don’t ruin the spark plug wires. This should stop the leakage, if not then you have a defective coil/ coil pack and need to see if there is a carbon track or a crack in the coil assembly itself, let me know if this helps and get back to me if you need more assistance.
http://shop.advanceautoparts.com/webapp/wcs/stores/servlet/partlist_Ignition-Coil_190_R%7CGRPTUNEAMS__coil___

Jul 24, 2009 | 2006 Ford Laser

2 Answers

94 toyota camery no spark


I had the same problem recently but replacing the ignition Coil under the distributor (inside) solved the problem. Also replaced the distributor Cap and rotor at the same time.

Jul 18, 2008 | 1994 Toyota Camry

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

45 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

Marvin
Marvin

Level 3 Expert

85206 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

john h

Level 3 Expert

22486 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...