How do you install a turn signal bulb in a 1962 chevrolet

Looks like to Nova with 300 horsepower versus 150 for the Corvair.

1962 Chevrolet Corvair Series Specifications

Concept Carz https://www.conceptcarz.com > chevrolet-corvair-series

The 1962 Chevrolet Corvair Series measures 180.00 inches in length, and has a wheelbase of 108.00 inches. 1962 Chevrolet Corvair Series. Article · Image gallery ...
Weight: 2350 lbs ' 1065.942 kg
Drive Type: Rear Wheel
Engine Location: Rear

Chevrolet Chevy II / Nova

Wikipedia https://en.wikipedia.org > wiki > _Nova

A 327 cu in (5.4 L) V8 was available with up to 300 hp (220 kW), suddenly putting Nova SS performance practically on a par with the GTO, 4-4-2, and 271 bhp ...
Model years: 1962-1979; 1985-1988
Manufacturer: Chevrolet (‎General Motors‎); ‎NU...‎
Production: 1961-1979; 1985-1988
Class: Compact (1962-1979); ‎Subcompact‎ ...‎ ‎History · ‎Origin · ‎Nova SS · ‎International Novas

all cars can hit 85 to 110 mph.

you have a bad ground for that tail light, trace the wires and see where the ground wire attatches to the body.

The bulb for the turn signal/brake light is a double filament bulb. It will come on with the lights on, but should light the second filament, making it brighter, with the brakes applied or turn signal on. It could just be a bad bulb, but one common problem on these years of truck is the rear light circuit board and requires the whole assembly to be replaced. Start by checking the bulb first though.
Hope this helps. Good luck!

1. Open the hood.
2. Remove the park/turn signal lamp assembly.
3. Remove the headlamp retainer pins.
4. Pull out the headlamp assembly in order to access the electrical connector.
5. Disconnect the electrical connector.
6. Remove the bulb from the headlamp assembly by twisting the bulb counterclockwise.

INSTALLATION PROCEDURE

IMPORTANT:

• Replace a high beam bulb with another high beam bulb. The high beam bulb has a red gasket.
• Replace a low beam bulb with another low beam bulb. The low beam bulb has a gray tip and a yellow gasket at the base.

1. Install the new bulb to the headlamp assembly by twisting the bulb clockwise in order to lock in place.
2. Connect the electrical connector to the bulb.
3. Install the headlamp assembly.
4. Install the headlamp retainer pins.
5. Rotate and lock the pins in place.
6. Install the park/turn signal lamp assembly.
7. Inspect the operation.

Check all turn signal bulbs, front and back, you probably have a blown bulb that is shorting the circuit. If all lights are ok, try removing them and installing one by one while circuit is energized, tif the fuse is blown on the first bulb try another location, his way you double check that the bulbs are not at fault. if it blows the fuse again, check your turn signal switch, it may be defective.

Good Luck!! Don't forget to rate this post!!

Removal & Installation Cab/Chassis

To Remove:

1. Disconnect lamp assembly electrical connector.
2. Remove nuts and lamp assembly from bracket.
3. Remove lens screws.
4. Remove lens, gasket and bulb.

To Install:

1. Install lamp assembly and nuts to bracket.
2. Connect electrical connector.
3. Install bulb, gasket and lens.
4. Install lens screws.

Except Cab/Chassis

To Remove:

1. Lower endgate.
2. Remove 2 tail/turn signal lamp assembly retaining screws.
3. Rotate tail/turn signal lamp assembly and remove from vehicle.
4. Disconnect lamp assembly electrical connector.
5. Remove bulbs by pulling straight out of bases.

To Install:

1. Install bulbs by pushing straight into bases.
2. Connect electrical connector.
3. Install tail/turn signal lamp assembly to vehicle and secure with 2 screws.

Once you open your hood look on the back of the headlight assembly. Twist the connector on the back of the turn signal and the bulb will come out. Then just replace with the correct bulb twist it back in and then test the blinker.

Signal and Marker Lights - REMOVAL & INSTALLATION
Front Turn Signal and Parking Lights
(see Figures 1, 2, 3, 4 and 5)



Fig. 1: Remove the retaining bolts for the splash shield and ...



Fig. 2: ... remove the splash shield from the vehicle



Fig. 3: Twist the bulb socket to remove it from the lamp and ...



Fig. 4: ...lower the socket down to access the bulb



Fig. 5: Pull the bulb straight out to remove it from the socket

1. Remove the inner wheel well splash shield.
2. Grasp the bulb socket and rotate it counter-clockwise to remove it from the lamp.
3. Remove the bulb from the socket.
4. Installation is the reverse of removal.

Hope helped with this (remember rated and commented this help).

There are 2 pins and 2 bolts that hold in the head lamp. Remove the head lamp to access the signal bulb. Good Luck