Question about 2006 Chevrolet Colorado

1 Answer

How do i change out the knock sensor on a 2006 chevy colorado

How do i change out the knock sensor on 2006 chevy colorado

Posted by on

  • 4 more comments 
  • Anonymous Mar 13, 2014

    Location of crankshaft sensor on 05 chevy Colorado 2.8l

  • Anonymous Mar 24, 2014

    where is the crankshaft sensor on a 2008 chevy colorado 2.9l engine located

  • Anonymous Mar 25, 2014

    fuel lines routing

  • Anonymous Mar 25, 2014

    fuel lines

  • Anonymous Mar 27, 2014

    remove the lumbar knob

  • Anonymous Mar 27, 2014

    how to remove the lumbar knob

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chevrolet Master
  • 2,989 Answers

You didn't list your engine size so please pick the applicable to your motor size:

Removal & Installation 2.8L & 2.9L Engines To Remove:

  1. Lift the vehicle high enough to gain access to the knock sensor (KS) through the left front wheelhouse.
  2. Remove the left front wheel and wheelhouse liner.
Knock sensor (KS) (A), Engine harness (B), Knock sensor (KS) connector (C)


how do i change out the knock sensor on a 2006 che - e44e83f.gif
  1. Disconnect the knock sensor (KS) connector.
  2. Detach the knock sensor (KS) from the engine block.
To Install:
  1. Attach the knock sensor (KS) to the engine block.
    • Tighten the bolt to 18 ft lbs (25 Nm).
  2. Connect the knock sensor (KS) connector.
  3. Install the left front wheelhouse liner and wheel.
  4. Fully lower the vehicle.

Posted on Sep 03, 2009

  • Greg Bernett
    Greg Bernett Sep 03, 2009
  • Disconnect the knock sensor (KS) connector.
  • Detach the knock sensor (KS) from the engine block.

  • To Install:


    1. Attach the knock sensor (KS) to the engine block.

      • Tighten the bolt to 18 ft lbs (25 Nm).

    2. Connect the knock sensor (KS) connector.
    3. Fully lower the vehicle.

  • Greg Bernett
    Greg Bernett Sep 03, 2009

    Knock Sensor (KS) 2
    Removal & Installation
    3.5L & 3.7L Engines
    To Remove:


    1. Lift the vehicle high enough to gain access to the knock sensor (KS) 2 through the left front wheelhouse.
    2. Remove the left front wheel and wheelhouse liner.

  • Disconnect the knock sensor (KS) 2 connector.
  • Detach the knock sensor (KS) 2 from the engine block.

  • To Install:


    1. Attach the knock sensor (KS) 2 to the engine block.

      • Tighten the bolt to 18 ft lbs (25 Nm).

    2. Connect the knock sensor (KS) 2 connector.
    3. Install the left front wheelhouse liner and wheel.
    4. Fully lower the vehicle.

    ×

    Ad

    1 Suggested Answer

    6ya6ya

    6ya staff

    • 2 Answers

    SOURCE:

    Hi there,
    Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

    Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

    Here's a link to this great service

    Good luck!

    Posted on Jan 02, 2017

    Ad

    Add Your Answer

    Uploading: 0%

    my-video-file.mp4

    Complete. Click "Add" to insert your video. Add

    ×

    Loading...
    Loading...

    Related Questions:

    1 Answer

    Where is the camshaft position sensor on 2006 chevy colorado?


    Evidently there are two of them. Your trouble code might tell us which one?
    camshaft position sensor-cciybiryczp3xgk1gpqrsmjv-4-0.jpg

    Apr 10, 2018 | 2006 Chevrolet Colorado

    1 Answer

    2006 Chevy Colorado 2.8 4 cyl. Engine is surging under normal acceleration. It has about 85K.


    Clean the MAF sensor and the throttle body. Plus the Idle air control motor. Use a toothbrush with brake clean. Just spray the MAF with brake clean both ways..

    Oct 04, 2014 | 2006 Chevrolet Colorado

    2 Answers

    2006 chevy colorado abs light on changed left speed censor


    if you broke sensor wire at the electrical connector.the dealership more likely can get you another sensor connector with new wires splice in new wires and connector.

    Nov 12, 2011 | 2006 Chevrolet Colorado

    1 Answer

    Changed my front brakes and rotors..ABS light came


    did you knock off a wire on the sensor ,or even break the sensor unit when you changed the rotors..

    Jul 11, 2010 | 2006 Chevrolet Colorado

    2 Answers

    Rough idle


    I had the same exact problem on my 2004 Colorado (3.5L). Cleaned the MAF sensor (with MAF sensor cleaner) and throttle body/plate - cleared it right up.

    May 10, 2009 | 2006 Chevrolet Colorado

    Not finding what you are looking for?
    2006 Chevrolet Colorado Logo

    Related Topics:

    3,653 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Chevrolet Experts

    Marvin
    Marvin

    Level 3 Expert

    85206 Answers

    Jonah Oneal

    Level 3 Expert

    14092 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22484 Answers

    Are you a Chevrolet Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...