Ford Escort/Tracer 1991-1999 Repair Guide
REMOVAL & INSTALLATION 1.8L Engine
(see Figures 1, 2, 3 and 4)
To install:
Fig. 1: Timing marks are located on the camshaft pulleys as shown-1.8L engines
Fig. 2: Make sure that the crankshaft sprocket (timing belt pulley) and oil pump timTiming belt timing marks, 1997 ford escort - 9cafc26.jpgre aligned-1.8L engines
Fig. 3: Align the timing belt pulley mark wTiming belt timing marks, 1997 ford escort - 72dc9cd.jpgsion set mark, at approximately the 10 o'clock position-1.8L engines
Fig. 4: Check the timing belt deflection at the location shown-1.8L engines
If the timing marks are not aligned, remove the belt and repeat the procedure.
I hope help you with this; remember rated this help. Good luck.
SOURCE: where can i find the timing marks on 1998 ford escort zx2 ?
Hello pamgolmon: My name is Roger and i will answer your question. The 2-0 dual cam engine is a interference engine. This means if the engine jumps time at the timing belt. It will bend the valves. As for the timing marks on the camshafts. Their are no marks to be located. To set the timing marks on this engine requires special tools. This makes it expensive for not only the do it yourself mechanic but also the repair shops also. If the valves were bent you must pull the head for the repairs also.
I know this is not the answer you were hoping for but it is the only answer to give. Please rate the quality of the answer as this way we know your answer was correct. Please just ask if you need further help. Thank You for using Fix Ya. Roger
SOURCE: timing marks 2000 ford escort
Hi!!
Here are 3 diagrams that correspond to the 3 engines types available for your vehicle.
Fig. Be sure that the intake and exhaust camshaft timing marks align so that they face each other-Ford 2.0L (VIN A) engines
2.0L (VIN P) Engines
Fig. Align the timing marks before removing or installing the timing belt-2.0L (VIN P) SOHC engines
Fig. Crankshaft alignment position-Ford 2.0L DOHC Zetec engines
In case the diagrams don't show, click the following link http://www.autozone.com/autozone/repairinfo/repairguide/repairGuideContent.jsp?chapterTitle=Engine+Mechanical+Components&partName=Engine+Mechanical&pageId=0996b43f802e7310&subChapterTitle=Timing+Belt&partId=0996b43f802e7275#hd1-1-3
Don't forget to rate this answer, GOOD LUCK
SOURCE: timing belt diagram for 2001 ford escort zx2 dohc
cam shaft timing marks on back of cams ,two slots ,use a flat piece of metal to align .remove no1 spark plug and drop long thin screwdriver down it to bring piston just below tdc,then align cams so both cams are on the rock (valves closed) with knob on back cam aligning with pick up sensor left side between lobes.then bring piston up to tdc and fit belt.turn engine over twice with socket on bottom pulley to make sure no valves clear pistons.Remember to remove flat edge from back of cams i didnt last time and bent my home made tool
SOURCE: setting timing marks on a 1998 Ford Escort
think u need a tool it locks the engine at top dead centre then u line cams up
SOURCE: timing marks on a 1996 ford escort 1.9L SEFI 4 cyl
im asuming all repairs went well,one,get a clean rag and wipe the gears and i mean wipe them clean two wipe and clean the plates behind them, three,lets start at the top find the dots on the gear you will see a tiny dot/indent four, look at the plate/caseing behind it and you will see another dot/indent,line them all up GEAR DOT to BACK DOT,five keep them in line and dont move them once you a satisfied all is in place and lined up and i mean lined up there is no room for error,fit belt and tighten .adrian,,,,,,,,
7,284 views
Usually answered in minutes!
×