SOURCE: 08 toyota sienna van and oil filter change
a local auto parts store will have every thing you need including manuals
SOURCE: hoist to lower spare tire does not work.
Same thing happened to me on my 2002 trailblazer. The last few wraps of the cable was corroded to the point that it wouldn't unwind with the tool supplied. First thing to do is cut the crimped end of the cable off with a grinder or cut off wheel but don't forget to support the spare. This will get the spare out of your way then simply take out the 3 mounting bolts for the cable hoist. At this point you could buy a new cable hoist from the dealer and install it yourself or you might be able to do what I did. I managed to pull and remove about a foot of the rusted cable, slide the rectangular metal piece, that actually holds the spare at the center of the wheel, back on the cable and attach a 1/4" cable clamp to the end of the cable which of course must be in good condition. There should still be enough cable to re-attach your spare to it and hoist it back up. Don't forget to lube things up so it won't happen again. Good luck. (buying a new one sounds better, doesn't it?)
mikethemedic in Hawley,Pa.
SOURCE: '93 Chev Suburban engine knock, sounds like rod
MAKE SURE THE CRANKSHAFT IS NO DAMAGED.IF IT IS THE NEW BEARINGS WILL GO BAD QUICKLY
SOURCE: 2007 Chevy Suburban rotor removal
this is a problem that happens alot you have to use an impact driver for this and a impact torx bit. the driver is a cylinder shaped tool with a 3/8 drive head. you get the impact torx the the impact driver and a hammer. the tool is inexpensive and will do the trick.
SOURCE: Need instructions on RF door panel 2000 deville
You'll need to remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. If needed, you can pull back the weather seal (can't reuse it, but it's not that important) and you will be able to access everything inside the door
NISSAN STANZA WAGON - Manual Transmission
Q. Where is the starter on a 1986 nissan stanza station wagon and how do you get to it ?
Due to limited access to the starter, it is recommended that the transaxle be removed when servicing the starter.
REMOVAL:
1. Cold vehicle.
Remove 2 mounting bracket bolts, 10 & 12 mm (Figure 1).
Remove top starter motor bolt 14 mm with universal & long extensions.
Raise vehicle on hoist.
Remove front splash pans 10 mm.
Automatic transmission: Drain 2 qts out.
Remove rt-ft wheel 21 mm., & tie rod (Figure 3), axle cap, cotter pin, adj-nut & rubber washer.
Remove ball joint nuts 17 mm., left lower control arm 19mm. & swaybar bracket 14 mm. (Fig 2).
Remove axle nut 36mm (Figure 4), the front tube, catalytic converter heat insulators 10mm, ctr ex-tube 17 mm., and front tube from exhaust system (Figure 5).
Remove long bolt from ft engine mount (next to radiator), 17mm socket (Figure 6, Item A).
Remove tension rod mount 14 mm. Has adj-bracket with rubber insulators (Fig 6, Items B, C).
Remove right side drive shaft bolts that hold shaft to bracket mounted on engine (Fig7) 12mm.
Remove rt-driveshaft.
CAUTION: Transaxle side seals are cut by spline teeth.
Install hoist type transmission jack and wooden block under the transmission/engine. Be certain the transmission is safely balanced on the hoist.
Remove 5 engine crossmember mounts (3 bolts, 2 nuts) 14mm.
Remove nut that attaches crossmember to engine mount.
Loosen stabilizer bar mounts to allow adequate clearance for crossmember to be removed.
Remove following brackets to allow starter assembly to pass through bottom:
tubular support bracket - engine to transaxle
angled support bracket - driveshaft bracket to engine mount
manifold collector stay - (bottom bolts)
Loosen top bolts, remove bracket above driveshaft-holding bracket 14mm.
NOTE: This bracket is slotted to allow it to slide out without completely removing the bolts.
Remove bottom starter motor mounting bolt.
Separate starter assembly from bellhousing, DC all cables/connectors, remove starter motor.
When installing starter, connect cable, install/torque starter bolts.
49 views
Usually answered in minutes!
×