Need radio wiring diagram for 2000 pontiac grand prix factory diagram

SOURCE: I need a wiring diagram for my 2000 pontiac grand prix

I own a 2001 Pontiac Grand Prix GTP and may be able to help you out if you let me know what specifically you are looking for.

SOURCE: Radio Wiring Diagram

Go to www.crutchfield.com.

On the bottom of the page there is a link for product support. On the next page, type "2005 Grand Prix" in the search box and hit enter. The top link shows an image and pinout on models with Monsoon sound systems, the second link for ones without.

Hope that helps! Good luck!

SOURCE: diagram on a pontiac grand prix

Ignition Switch GM Century/Lumina/Grand Prix/Intrigue 1997-2000 The vehicles covered by this guide use one of two types of ignition switches:

• A mechanical key and lock cylinder built into the steering column, that works a pull rod to actuate the separate electrical portion of the ignition switch mounted further down the steering column. For more information and replacement procedures on this type of switch, please see .
• An instrument panel-mounted ignition switch is also used on some W-Body vehicles. To service this switch, the radio, heater & A/C control panel and the instrument cluster must be removed. All of these procedures are found elsewhere in this section.

REMOVAL & INSTALLATION
Instrument Panel-Mounted Ignition Switch
WARNING You must perform the Body Control Module (BCM) theft deterrent relearn procedure after replacement of the ignition lock cylinder. Failure to perform this relearn procedure means the BCM will not function properly. This means the vehicle will not be theft protected by the Passlock system and the engine may not crank or start. GM recommends that this procedure be performed with their Tech 2® or equivalent scan tool. An alternate relearn procedure is given at the end of this procedure.

1. Disconnect the negative battery cable.
2. Remove the radio assembly following the procedures found in this section.
3. Remove the heater & A/C control head assembly following the procedures found in this section.
4. Remove the instrument cluster assembly following the procedures found in this section.
5. Detach the electrical connectors from the ignition switch.
6. Insert the key and turn the ignition switch lock cylinder to the ACC position.
7. Depress the transaxle park/lock cable retainer to release, then pull to remove the cable from the ignition switch.

NOTE You must perform the Body Control Module theft deterrent relearn procedure after replacement of the ignition lock cylinder.

1. If it is necessary to remove the ignition lock cylinder from the ignition switch (theft damage, etc.), use the following procedure:
   1. Insert the key and turn the ignition switch lock cylinder to the ON position.
   2. Using a small flat-bladed tool, depress and hold the lock cylinder retaining tab.
   3. Using the key as an aid, pull to remove the ignition switch lock cylinder from the switch.
   4. Remove the key from the lock cylinder.
   5. Carefully pull to release the ignition switch bezel from the ignition switch lock cylinder.
2. Remove the ignition switch bracket bolts and remove the ignition switch through the instrument panel cluster opening.
3. Remove the bolts retaining the ignition switch to the bracket and remove the bracket.

Removing an instrument panel-mounted ignition switch assembly—1998 Oldsmobile Intrigue shown, others similar To install:

1. Install the ignition switch to its bracket and install the bolts. Install the ignition switch into position through the instrument panel cluster opening and install the bracket retaining bolts.
2. If removed, install the ignition switch lock cylinder to the ignition switch using the following procedure:
   1. Recode the lock cylinder, if necessary.
   2. Align the ignition switch bezel to the tabs on the ignition switch lock cylinder and carefully press to secure in place.
   3. Insert the key and turn the ignition switch lock cylinder to the ON position.
   4. Align the ignition switch lock cylinder to the ignition switch, then press into place.
3. Turn the key to the ACC position. Align and press into place the transaxle park/lock cable to the ignition switch. Remove the key from the switch.
4. Attach the electrical connectors to the ignition switch.
5. Install the instrument cluster using the procedures found in this section.
6. Install the heater & A/C control panel using the procedures found in this section.
7. Install the radio assembly using the procedures found in this section.
8. Connect the negative battery cable.
9. If the lock cylinder was removed, perform the BCM Programming/RPO Configuration procedure.

THEFT DETERENT RE-LEARN—WITHOUT TECH 1®SCAN TOOL
This procedure takes approximately 30 minutes. Make sure the battery is fully charged before proceeding.

1. Turn the ignition switch to the OFF position.
2. Turn the ignition switch all the way from the OFF to the START position, then leave it in the ON position. The engine will not crank.
3. The SECURITY light should come on and stay on for at lease ten minutes.
4. Turn the ignition switch to the OFF position for five seconds.
5. Repeat Steps 2, 3 and 4 again for a second time.
6. Repeat Steps 2, 3 and 4 again for a third time.
7. Turn the ignition switch to the OFF position.
8. Turn the ignition switch all the way to the START position. The engine should now start.

SOURCE: 2000 pontiac grand prix se ecm location

located in air box beather box for intake.

SOURCE: i want to install a

Under the steering wheel by your feet, remove the 2 screws that hold the panel up. Carefully remove that, then just take your hands and start popping the dash off, but be CAREFUL!