Question about Jeep Cars & Trucks

Open Question

The fuse system in the jeep we have is only 5 and we are trying to replace the fuse for the wipers front and back as well as the washer fluid

Posted by on

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Anonymous

  • 98 Answers

SOURCE: Washer fluid not working

There is a fluid "pump" that is generally below the washer fluid reservoir under the hood. To check if the pump is bad try to spray some fluid and have someone listen under the hood while you are doing this. If they hear a hum or the system sounds like it is active but you are getting no fluid spraying out then you probably have a kink or stoppage. The spray nozzles are right below the windshield wipers and sometimes a piece of debris has lodged itself in. You can take a safety pin or something similar and try to get it out that way. If not you may have to take the hose apart and clean it that way. Hope this works for you.

Posted on Feb 25, 2009

Ad
ZJLimited

ZJ Limited

  • 17970 Answers

SOURCE: The Rear wiper stopped working on my 96 jeep cherokee sport

You can read this Factory Service Manual for ZJ-Secc-8K-Windshield-Wiper-and-Washer-Systems (page 7 and next), there you can begin to the fix.

Good luck!!!

Posted on Feb 25, 2009

Richard Scordino

  • 6982 Answers

SOURCE: My 2005 Jeep Grand Cherokee's windshield washer is not working.

Check power at the pump motors. You may not see a fuse because some run off a circuit breaker. If all else fails, a bit "backyard" but you likely could break out the washer pumps from the system and make a simple push button on the dash to operate them.

Posted on Jul 08, 2009

Anonymous

  • 164 Answers

SOURCE: Jeep Liberty 2005 Rear Wiper Not working. Change

could be the arms striped ore the motor shot on it

Posted on Jul 28, 2009

Anonymous

  • 5 Answers

SOURCE: My front windscreen wipers on my BMW mini are not

i repaired mine in about an hour , the motor contactor will be burnt out , this can be rapaired easily by soldering , the motor can be removed fairly easily without all the uneseccery strip down as many people think , if you would like the strip dwon procedure let me know

Posted on Feb 05, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where can I find the fuse for the wipers for my 2002 Lincoln town car


Highly doubtful it being a blown fuse . Fuse's don't just blow , short circuit to ground or high current draw . Faulty component , wiper motor , wiper control module more likely . Free wiring diagrams here http://www.bbbind.com/free-tsb Enter vehicle info. year , make , model an engine size . Under system click on body & accessories . then under subsystem click on wiper / washer , Click the search button ,then the blue link . Looking at the diagram i see the wiper switch is a input to the wiper control module .

The windshield wipers are controlled by the wiper control module and the driver-operated multi-function switch on the steering column, with the ignition switch in RUN or ACC position.
There are four modes of wiper operation: OFF position, the wipers move to and stay in the park position; Interval position, the wiper control module causes the wipers to cycle, separated by pauses, pause time length being determined by switch location; LO position, the wipers will operate at low speed continuously; HI position, the wipers will operate at high speed continuously.
The windshield washers are controlled by pressing inward on the wiper switch end of the multi-function switch. The washers will operate as long as the switch is depressed. If the wipers are in the OFF or Interval operating mode, the wipers will begin in LO speed and the washer pump will pump fluid from the reservoir to the nozzles. When the switch is released, the wipers will complete three cycles and then return to their previous setting. In LO or HI mode, no change in wiper operation will occur during washer operation.
The washer fluid level sensor is in the windshield washer reservoir (17618) and is monitored by the hybrid electronic instrument cluster (HEC) and displays a WASHER message when the fluid level is low. The washer fluid level sensor and windshield washer reservoir are replaced as an assembly.

  • The Wipers are Inoperative
  • Fuse.
  • Wiper motor.
  • Multi-function switch.
  • Circuitry.
  • Wiper control module.
  • GO to Pinpoint Test B .

PINPOINT TEST B: THE WIPERS ARE INOPERATIVE CONDITIONS DETAILS/RESULTS/ACTIONS B1 CHECK FUSE JUNCTION PANEL FUSE 16 (30A)
Fuse 16 (30A)

  • Is the fuse OK?
Yes GO to B2 .

No REPLACE the fuse. TEST the system for normal operation. If the fuse fails again, CHECK for a short to ground. REPAIR as necessary. B2 CHECK FOR VOLTAGE TO THE WIPER CONTROL MODULE - CIRCUIT 65 (DG)
Wiper Control Module C294
Measure the voltage between wiper control module C294-2, circuit 65 (DG), and ground; and between wiper control module C294-11, circuit 65 (DG), and ground.
  • Is the voltage greater than 10 volts?
Yes GO to B3 .

No REPAIR circuit 65 (DG). TEST the system for normal operation. B3 CHECK CIRCUIT 57 (BK) FOR OPEN Measure the resistance between wiper control module C294-3, circuit 57 (BK), and ground; and between wiper control module C294-5, circuit 57 (BK), and ground.
  • Are the resistances less than 5 ohms?
Yes GO to B4 .

No REPAIR circuit 57 (BK). TEST the system for normal operation. B4 CHECK THE MULTI-FUNCTION SWITCH
Multi-Function Switch
Check the multi-function switch; refer to Section 211-05 .
  • Is the multi-function switch OK?
Yes GO to B5 .

No REPLACE the multi-function switch; REFER to Section 211-05 . TEST the system for normal operation. B5 CHECK CIRCUIT 993 (BR/W) FOR OPEN Measure the resistance between multi-function switch C269-4, circuit 993 (BR/W), and wiper control module C294-7, circuit 993 (BR/W).
  • Is the resistance less than 5 ohms?
Yes GO to B6 .

No REPAIR circuit 993 (BR/W). TEST the system for normal operation. B6 CHECK CIRCUIT 589 (O) FOR OPEN Measure the resistance between multi-function switch C269-1, circuit 589 (O), and wiper control module C294-1, circuit 589 (O).
  • Is the resistance less than 5 ohms?
Yes GO to B7 .

No REPAIR circuit 589 (O). TEST the system for normal operation. B7 CHECK THE WIPER CONTROL MODULE OUTPUT FOR VOLTAGE
Wiper Control Module C294

Wiper Motor C152
Turn the multi-function switch to the HI position. Measure the voltage between wiper motor C152-4, circuit 57 (BK), and wiper motor C152-3, circuit 56 (DB/O).
  • Is the voltage greater than 10 volts?
Yes REPLACE the wiper motor; REFER to Motor-Windshield Wiper . TEST the system for normal operation.

No GO to B8 . B8 CHECK CIRCUIT 57 (BK) FOR OPEN Measure the resistance between wiper motor C152-4, circuit 57 (BK), and ground.
  • Is the resistance less than 5 ohms?
Yes REPLACE the wiper control module; REFER to Module-Windshield Wiper . TEST the system for normal operation.

No REPAIR circuit 57 (BK). TEST the system for normal operation.

Jun 13, 2018 | Lincoln Cars & Trucks

2 Answers

2010 Reg Ford Focus 5 door hatch rear screen wash not working. Front is OK. How do I fix it?


the washer fluid could be empty / the fuse for the wiper blew / the relay went bad /if you tried to use the wipers without clearing ice away you blew the fuse/ if you just put water in instead of washer fluid it's frozen/ if the wiper works and there is windshield fluid in the tank and not water and all fuses are good the pump motor for the fluid went and is easy to change

Feb 25, 2015 | Ford Cars & Trucks

1 Answer

1997 Jeep Cherokee -- Do the front windshield wipers/washer fluid have a fuse? It isn't listed in my owners guide in either of the fuse box locations. They stopped working.


wipers and washers usually have a fuse,
i may be mixed with another fuse.
the best thing to do is check each fuse in turn and see if one is blown or has
corroded connections.


I hope this was helpful.

Jan 11, 2011 | 1997 Jeep Wrangler

2 Answers

Hi...I have a 1999 Jeep cherokee Sport. The windshield washer quit..dont know if it is a clogged line or a pump. Not hearing the pump when I activate. Also lines appear to be hidden.


This is most likely due to the washer pump going out. I just replaced mine on my 2000 cherokee. There is a front and back pump which is located under the drivers side fender. You will have to remove the plastic corner bumper to get access to the pumps. This is an easy job to do yourself. Dont forget to have something ready to drain the fluid into when you remove the pump from the washer tank. The front pump is located below the rear pump.

Dec 01, 2010 | 1999 Jeep Cherokee

2 Answers

My 96 Jeep GC windshield washer isn't squirting. I can hear it run when pushing the washer button and I hear fluid running ; but it doesn't spray on the windshield. Also , my wiper blade in the rear window...


your rear wiper motor might be faulty,in the front i would check your fluid level-if it is full and you hear the pump running-check your washer lines to see if they are pinched-usually around where the hood closes

Feb 17, 2010 | 1996 Jeep Grand Cherokee

1 Answer

Both the front and rear washers are not working, which fuse controls this?


When you attempt to use you washers do you 1 hear a noise and no fluid or 2 if no noise no fluid, skip to 3 If 1 check your reservoir fluid level if full check nozzles for wax- polish blocking opening if clean. trace windshield hose to reservoir pull both end loose and Blow air through if clear push back on.
3 Check fuse panel if not marked wiper/washer and you do not have a manual replace all broken fuses your bound to get it that way

Jul 09, 2009 | 2005 Jeep Grand Cherokee

1 Answer

Washer fluid will not spray in 1999 Jeep Cherokee sport


If there is a hum when you press the washer button but no fluid than try cleaning the holes where the fluid comes out if that don't work than try replacing the supply hoses. If there is no hum than first check the fuses and if they arn't blown than you more than likly have a faulty motor. Both? unlikely but not impossible. Good luck.

May 17, 2009 | 1999 Jeep Cherokee

1 Answer

Front widshield washer fromm 1999 Cherokee doesn't work


Your rear bottle for the wipers should be at the back of the vehicle.Look in back for removable panel and bottle should be there.Turn your ignition on(no start)and activate rear washer Listen for the sound of the motor

Nov 20, 2008 | 2000 Jeep Cherokee

1 Answer

Front widshield washer fromm 1999 Cherokee doesn't work


the same reservoir is used for both ...it uses separate pump motors.....if the wipers are working the fuse for the washer pump is good...check the power and ground for the pump...

Nov 01, 2008 | 1999 Jeep Cherokee

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

22 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

Marvin
Marvin

Level 3 Expert

85206 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...