How to locate the air blend door in a 1990 Cadillac Fleetwood? Where is it? Removed glove box and cannot find it

1996 Chevrolet K1500 Air Blend Door Actuator

Advance Auto Parts https://shop.advanceautoparts.com > ... > AC Actuators
This air door actuator directly replaces the original actuator on specific vehicle years, makes, models, configurations and positions to restore proper HVAC ...

Blend door actuator

GMT400 https://www.gmt400.com > threads > blend-door-actua...
May 3, 2021 - The blend door is in the middle of the dash and mounted on the coil box. The one by the blower controls the damper that directs air intake from ...

VCAUTO HVAC Blend Door Actuator for 1996-2013 ...

Amazon.com https://www.amazon.com > VCAUTO-Actuator-1996-...
VCAUTO HVAC Blend Door Actuator for 1996-2013 Chevrolet Express 1500 2500 3500; 1996-2013 GMC Savana 1500 2500 3500; 1996-2013 Cadillac DeVille 604-125.

Dennis, You have 2, open glove box, bend tabs on glove box and pull down to over open glove box, actuators are on ductwork both sides. link to video showing how.

2008 dodge avenger blend air actuator location

https://www.google.ca/url?sa=t&rct=j&q=&esrc=s&source=web&cd=2&cad=rja&uact=8&ved=0ahUKEwiEvbbWg4rLAhXFpR4KHY1zB_EQtwIIHjAB&url=https%3A%2F%2Fwww.youtube.com%2Fwatch%3Fv%3DKD7NYlEXhcY&usg=AFQjCNFVKlo1Rkv6C2Km0B1jmcoLhFeQHQ

2006 dodge charger blend door actuator location Google Search

your blend doors will be behind your dash ...it will have to be removed

usually it is in the dash and the glove box needs to be removed to get to the actuator.

Same problem on my 98 Regal GS; remove glove box, locate the blend door actuator, (black odd shaped box with metal "ring"). Remove the box and manually turn the blend door shaft it was attached to. If you get cold air, it's the actuator you removed. About 30-40 dollars.

Same problem on my 98 Regal GS; remove glove box, locate the blend door actuator, (black odd shaped box with metal "ring"). Remove the box and manually rotate the blend door shaft it was attached to clockwise. If you get cold air, it's the actuator you removed. About 30-40 dollars.

On the frame directly below the rear passenger door. its bolted to the frame...got this from answer.com fuel filter of cadillac 1990 fleetwood located?

there is a blend door actuator for the laredo and if is bad the air wont come out here is a pic of what it looks like and how to get to it


The single zone heater-A/C system is equipped with a single blend door actuator. The dual zone system has two blend door actuators, one for the driver side blend-air door and one for the passenger side blend-air door.

1. Disconnect and isolate the negative battery cable.
   
2. Remove the glove box from the instrument panel.
3. Remove the three screws that secure the blend door actuator to the passenger side of the HVAC air distribution housing .
4. Remove the blend door actuator from the air distribution housing and disconnect the HVAC wire harness connector from the actuator.
5. Remove the blend door actuator from the vehicle

to instal

1. Position the blend door actuator into the vehicle.
2. Install the blend door actuator onto the passenger side of the HVAC air distribution housing . If necessary, rotate the actuator slightly to align the splines on the actuator output shaft with those on the blend door cam .
3. Install the screws that secure the blend door actuator to the passenger side of the air distribution housing . Tighten the screws to 17 inch lbs. (2 Nm).
4. Connect the HVAC wire harness connector to the blend door actuator.
5. Install the glove box into the instrument panel.
6. Reconnect the negative battery cable.

The ducting to the left must be fed from the heater box. Yet the blend door must not be sealing allowing the cold air the blend with the hot. Check the blend door mechanism, behind glove box, or some dash panels may need to be removed to access this door.

The heater and a/c blend door actuator motor is located behind the center of the dash just below the windshield. The steering column must be detached and lowered and the dash must be removed to access the blend door motor.