Question about Mitsubishi Cars & Trucks

Open Question

Where is the crankshaft sensor located on a Mitsubishi Eclipse 2000 on need to replace mine

Posted by on

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Anonymous

  • 1 Answer

SOURCE: crankshaft position sensor location

if u pull the battery and battery tray u can easily reach this

Posted on Nov 23, 2008

Ad
Big Poppa Ma

Big Poppa Marv

  • 302 Answers

SOURCE: 2002 Eclipse

its by your intake manifold on the bottom of the engine block. there is a heat shield covering it which will need to be removed to get to it

Posted on Dec 06, 2008

Anonymous

  • 37 Answers

SOURCE: crankshaft position sensor location

Hello. One way to check if it is working is when you try to start the car does the needle move on you tac? If not then your crank sensor is more then likely the problem. It is located on the backside of the engine under the intake manifold. If is in about the center of the block. There will be a 10mm bolt holding the sensor in. If you decide to change it yourself (not to terrible of a job) unplug the sensor, remove the bolt and spin it back and forth slightly while pulling it out. It may be stoburn and you might have to work at it for a little bit (not a done of room) but it will come. When it's out the sensor will be shaped kind of like an L. I have changed a few of these over time and they can be a little stoburn. To install just reverse the process.

Posted on Mar 26, 2009

GARYca

Gary M

  • 672 Answers

SOURCE: Change a crankshaft position sensor on a 2000 eclipse

Is this a V6 or 4cyl???>>>(V6) This requires removing the Harmonic balancer (crankshaft pulley). Remove (R) front wheel, remove engine splash Guard, Remove crank pulley, remove lower timing belt cover. The Crank sensor is located behind the crank shaft pulley!! I highly recommend having this done by a certified tech, requires special tools. Hopefully this helps!!

Posted on Mar 11, 2010

Don Peterson

  • 1 Answer

SOURCE: I have replaced the camshaft sensor, Crankshaft sencor, computer, crankshaft pully, and new spark plugs on my 1999 Mitsubishi Eclipse and it still won't start, what could it be?

Engine needs spark, fuel and air to run. I assume the starter is turning the engine over. Have you verified you have spark at the plugs? Have you verified you have fuel pressure? Can you hear the fuel pump when you first turn the ignition key? If, yes to those, check the timing belt settings to make sure something hasn't caused the timing to change.

Posted on Mar 22, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 2000 eclipse 2.4 auto rs. Car just shut off while driving. Scanned the mil and showed a code for the camshaft position sensor. Car owners father replaced the crankshaft position sensor (dunno...


if the code shows a cam position sensor then it is the cam position sensor and not the crank position sensor
get the car to an accredited service center before it cost more money from inexperienced interference

May 28, 2017 | 2000 Mitsubishi Eclipse

1 Answer

Replacing crankshaft position sensor 2001 mitsubishi eclipse 2.4l


Access to the crankshaft sensor is impeded by the timing belt, which must be removed, on a 2001 Mitsubishi Eclipse 3.0L V6. -----------------------------------------------------------------------------------
Multidiag Actia

Jan 31, 2013 | Cars & Trucks

1 Answer

I have replaced the camshaft sensor, Crankshaft sencor, computer, crankshaft pully, and new spark plugs on my 1999 Mitsubishi Eclipse and it still won't start, what could it be?


Engine needs spark, fuel and air to run. I assume the starter is turning the engine over. Have you verified you have spark at the plugs? Have you verified you have fuel pressure? Can you hear the fuel pump when you first turn the ignition key? If, yes to those, check the timing belt settings to make sure something hasn't caused the timing to change.

Mar 22, 2012 | 1999 Mitsubishi Eclipse

1 Answer

Change a crankshaft position sensor on a 2000 eclipse


Is this a V6 or 4cyl???>>>(V6) This requires removing the Harmonic balancer (crankshaft pulley). Remove (R) front wheel, remove engine splash Guard, Remove crank pulley, remove lower timing belt cover. The Crank sensor is located behind the crank shaft pulley!! I highly recommend having this done by a certified tech, requires special tools. Hopefully this helps!!

Mar 11, 2010 | 2000 Mitsubishi Eclipse

1 Answer

2002 Eclipse


its by your intake manifold on the bottom of the engine block. there is a heat shield covering it which will need to be removed to get to it

Dec 06, 2008 | 2002 Mitsubishi Eclipse

2 Answers

Crankshaft position sensor location


under hood, center, upper engine area, mounted on upper driver side of engine.

Nov 21, 2008 | 1996 Mitsubishi Eclipse

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

33 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

Marvin
Marvin

Level 3 Expert

85216 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...