How to remove the front passenger seat from a 2015 honda crv

https://www.hcrv.net/front_seat-1850.html

Ask honda

At least you can practice on the passenger seat first.

Firstly most modern car seats have at least one wiring connector underneath. Sometimes it is possible to disconnect first and sometimes it is easier to unbolt the seat first and gently tilt it backwards for greater access.

There will typically be at least one bolt at each corner, possibly two and these days there is often some cover trim to remove for access. The seat is then moved as far forward as possible to release the rear bolts and then moved rearwards to release the front bolts. Sometimes there isn't much room and backache is the result...

When refitting, run all the bolts home and then move the seat backwards and forwards several times during the final tightening.

look under seat make sensor for the seat did not come unplugged.

Is the light burned out? You will need the service or owners manual to help in replacing it.
The light is there as a reminder to not put a small infant in the front seat who could e seriously or fatally injured in a crash by being there.

if you plan to carry some cargo on the passenger seat, you just have to put up with the light. You can put some black tape over it if it bothers you temporarily.

I don't know if this is something you want to get into? You decide. Front Seat Belt Replacement SRS components are located in this area. Review the SRS component locations and the precautions and procedures before performing repairs or service.
NOTE: Check the front seat belts for damage, and replace them if necessary.

Front Seat Belt

1. Make sure you have the anti-theft code for the radio, and then write down the frequencies for the preset buttons.
2. Disconnect the negative cable from the battery, and wait at least 3 minutes before beginning work.
3. Slide the front seat forward fully.

1. Pull the lower anchor cover (A) back, and remove the lower anchor bolt (B).
2. Remove the B-pillar lower trim panel.

1. Remove the upper anchor cover (A), and remove the upper anchor bolt (B).

1. Disconnect the seat belt tensioner connector (A), and detach the harness clip (B) from the retractor (C). Remove the upper retractor mounting bolt (D), and the lower retractor bolt (E), then remove the front seat belt (F) and retractor.
2. If necessary, remove the front seat belt protector (G).
3. Remove the B-pillar upper trim.

1. Remove the shoulder anchor adjuster (A).

1. Install the seat belt in the reverse order of removal, and note these items:
   • Assemble the washers, collar, and bushing on the upper and lower anchor bolts as shown.
   • Check that the retractor locking mechanism functions.
   • Apply liquid thread lock to the anchor bolts before reinstallation.
   • If the seat belt tensioner has been activated, replace the front seat belt protector with a new one.
   • Before installing the anchor bolts, make sure there are no twists or kinks in the seat belt.
   • Make sure the seat belt tensioner connector is plugged in properly.
   • Reconnect the negative cable to the battery.
   • Enter the anti-theft code for the radio, and then enter the customer's radio station presets.
   • Reset the clock.
   • Do the PCM idle learn procedure and the power window control unit reset procedure.

Upper anchor bolt installation
Lower anchor bolt installation

Seat Belt Buckle

1. Make sure you have the anti-theft code for the radio, and then write down the frequencies for the preset buttons.
2. Disconnect the negative cable from the battery, and wait at least 3 minutes before beginning work.
3. Remove the front seat.
4. If equipped, remove the center table.
5. Remove the under seat storage box.
6. Remove the center cover, driver's, passenger's.

1. Driver's: If equipped with seat heater, remove the harness band (A), and disconnect the seat subharness connector (B). If equipped without seat heater, detach the seat belt switch connector clip (C). Detach the seat belt buckle tensioner clip (D), and harness clip (E).

with a SCANNER.
your mechanic or Honda Dealer will provide this service....
Disconnecting the battery won`t do you any good.
You will have to fix the air-bag problem first before you can erase the airbag light...

Here's a quick check list for most common cost of SRS / Air bag problem.


Dirty contacts on driver and passenger seat belt buckles

Dirty contacts on seat belt connectors (under seats)

Dirty contacts on driver and passenger sides weight sensors (under seat)

Seat covers

Weight on passenger seat

(Example: grocery package trigger SRS / Air Bag light on the way home.)

I recommend you to pass an vacuum over the contacts and use CRC electronic parts cleaner to rule out connectivity problem.

I DO NOT disconnecting the negative battery connector to clean the code(s)

Without the code(s) the dealer will takes "BILLABLE" time to reproduce the problem.

======

Please rate my answer if it is useful to you.


Cheers,

Mustgo

As I remember, you need to remove the front seat belt mount, & completely remove the back seats, in order to remove the rear door cards, without breaking them.
Have fun;)

You'll have to remove the plastic cover (from inside the vehicle), there there are three 10mm bolts that hold the base onto the door.