Question about Ford Cars & Trucks
First step ................................................... 23 Nm (17 lb-ft)
Second step .................................................. 43 Nm (32 lb-ft)
Third step (you need a torque angle gauge for this).... Tighten an additional 105°
Posted on Dec 08, 2019
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
Here's a link to this great service
Posted on Jan 02, 2017
I dont know the specific answer for your question, but I own a 1995 Rodeo and there is an online community you could probably check out that Im sure would have the answer for you.
Check out www.planetisuzoo.com, sign up and post your question there. There are several knowledgeable people there and some good information as well.
Posted on Jan 03, 2009
SOURCE: piston rod bearings
Hello capybluebloo: The torque specs are as follows. Step one tighten to 10-12 ft.lbs. Step two is to tighten an additional 60-65 degrease. I checked two different shop programs and they both say the same. I hope you have access to a degree meter as the degree is very important. Please leave a rating as to quality of your reply as it does help. Should you need more help just ask. Thank You for using FixYa. Roger
Posted on Apr 16, 2009
stage 1 tighten to 30 ft pounds
stage 2 tighten 90 degrees
stage 3 loosen one full turn
stage 4 tighten to 30 ft pounds
stage 5 tighten 90 degrees
stage 6 tighten 90 degrees
this is per mitchell on demand courtesy of ford specs on the lft and right head.
for some reason there are no torque specs on mitchell for connecting rods and mains.
Posted on Sep 16, 2009
Cylinder heat bolt torque:
Torque sequence --------- front | 7 3 1 5 | | 8 4 2 6 | --------- Step 1: Torque all bolts in sequence to 14 Ft/Lbs Step 2: Torque all bolts in sequence to 29 Ft/Lbs Step 3: Torque all bolts in sequence to 36 Ft/Lbs Step 4: in the sequence, loosen the cylinder head bolts three turns. Step 5: Tighten short bolt to 15 - 32 Ft/Lbs Step 6: Tighten long bolt to 30 - 36 Ft/Lbs Step 7: Tighten all bolt to 175- 185 degree note: Do not loosen all of the cylinder head bolts at one time. Each cylinder head bolt must be loosened and the final tightening prior on the next bolt in the sequence.
Main bearing torque:
Torque sequence: Step 1: torque bolts to 91 Ft/Lbs with the exception of the rear main bearing cap Step 2: torque rear main bearing cap bolts to 88 Ft/Lbs Step 3: torque brace bolts to 40 Ft/Lbs
Connecting rod torque:
Torque sequence Step 1: Torque to 29 Ft/Lbs Step 2: Turn an additional 90 degrees
Posted on May 18, 2010
Tips for a great answer:
Mar 06, 2018 | Cars & Trucks
Apr 24, 2017 | Dodge Cars & Trucks
Dec 09, 2016 | 2005 Chevrolet Equinox
Sep 17, 2011 | 1994 Ford F150 Styleside Supercab
Mar 23, 2011 | 1996 Mitsubishi Eclipse
Mar 04, 2011 | 1996 Chrysler Concorde
May 31, 2010 | 1995 Ford F150 Styleside Regular Cab
May 17, 2010 | 1997 Ford F150 Regular Cab
Sep 15, 2009 | 2006 Ford Five Hundred
May 27, 2009 | 1999 Ford Taurus
21 people viewed this question
Usually answered in minutes!