Question about Cars & Trucks
. have u referred to a help book? If u don't have it get one from google or find one from big-manuals com !!
Posted on Dec 11, 2019
Are you asking about the VVT Solenoids? If so they are located on top of the valve cover. Passenger side (Right Side) of engine compartment, closest to the timing chain but externally mounted. They at right next to Coil #1. The CKP sensor is located on the driver's side (Left Side) of the engine. Look for the starter. It is located slightly above the starter and close to the starter mounting flange. Anything else please let me know.
Posted on Dec 11, 2019
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
Here's a link to this great service
Posted on Jan 02, 2017
1990 Chevrolet Cavalier 2.2L TBI 4cyl
The Crankshaft Position Sensor is located under hood, center, rear engine area, below ingnition coil pack and DIS module, mounted in engine block.
Fig. 1: View of the CKP sensor-to-crankshaft reluctor relationship
Crankshaft Position (CKP) Sensor
A magnetic crankshaft sensor (Hall Effect switch) is used which is remotely mounted on the opposite side of the engine from the DIS/IC module. The sensor protrudes in to the engine block, within about 0.050 in. (1.27mm) of the crankshaft reluctor.
I really hope help you wuth this (rated this help). have a nice day, good luck.
Posted on Sep 25, 2009
Testimonial: "Awesome. Thanks."
It is located on the passenger side of the engine block just under the ignition module you can see it from underside. The easiest way to see it and access it is to jack up the passenger side front wheel and take the wheel off there is a rubber flap in the wheel well you can push out of your way. I am warning you be very careful removing it mostly made of plastic I broke one off leaving most of the sensor in the engine block had to drill the rest of it out which was no fun not alot of room for you to work. Get yourself a bottle of PB Blaster and keep spraying it as your pulling out before you try pulling out the sensor try to get it free enough that you can spin it around. Hope this helps good luck it fits pretty tight!
Posted on Oct 30, 2009
It mounts in the side of the block near the crankshaft,it fits in a hole,going into the engine block.,look on the inside of the engine compartment ,on the firewall side,left of the pulleys,down low.
Posted on Mar 22, 2010
the crankshaft postion sensor is always located either under the harmonic balancer pully aka crankshaft pully or mounted right outside the pully if yoiu need to change it keep in mind that you will need to to own or rent a harmonic balancer pully puller and a harmonic balancer pully installer kit both you can rent both at autozone fairly cheap and get all your money back when your done
job rating from 1-10 about a 3
hope it helps if so could you please leave me a 4 thumbs up feedback thank
Posted on May 12, 2011
Tips for a great answer:
Mar 16, 2017 | Cars & Trucks
Aug 19, 2015 | 1998 Oldsmobile Aurora
May 16, 2011 | 2007 Chevrolet Cobalt Coupe
Sep 12, 2010 | 2002 Volkswagen Passat
Jul 24, 2010 | 2005 Chevrolet Cobalt
Nov 29, 2009 | 2002 Chevrolet TrailBlazer
Jul 27, 2009 | 2005 Chevrolet Cobalt
Jan 25, 2020 | Cars & Trucks
15 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: