Question about Chevrolet Cars & Trucks
Most of them fasten on the bolts that hold your license plate on. Take the tail lights out and wire it to the back up lights. Then it should be wireless from there to the screen inside which you can hotwire t ok 13 volt or plug into a power port.
Posted on Jan 18, 2020
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
Here's a link to this great service
Posted on Jan 02, 2017
SOURCE: 2004 chevrolet trilblazer
There is a plate underneath the engine that is held in by 2 flat head screws. All you have to do is loosen both screws and slide the plate around. The plate just slides around. The drain plug and oil filter are then exposed and easily accessable. The 2004 Trailblazer takes 7 quarts of oil and uses an ACDelco PF61 or Fram PH3675 oil filter. I've read in this FAQ site some info about other filters, so I went down to the local Chevy dealer and talked to a mechanic. He told me the ACDelco PF61 was the correct filter. The Fram PH3675 is the exact same as the PF61.
Posted on Mar 31, 2009
SOURCE: 2004 Chevrolet Trailblazer
First face the vehicle so the battery in on the right.
Second open hood.
Third Remove the Grill by pushing firmly on two retainer clips that are on the top, use the wide slot screwdriver to get the rest of the clips off. Pull up gently on the grill it should then pop out. The grill extends under each headlight assembly any other retainer clips should release when the grill in popped out.
Replace the bulbs high beam on the outside and low beam on the inside.
Posted on Jun 19, 2009
FACE THE VEHICLE SO THAT BATTERY IS ON YOUR RIGHT;
2.REMOVE THE BLACK PLASTIC PIECE THAT RUNS OVER RADIATOR BETWEEN HOOD LATCH AND FAN. IT IS ABOUT 53 1/2" LONG AND HOLDS THE HOOD PROP CLIP. (3 PLASTIC PUSH RETAINERS & 2 SHEET METAL SCREWS);
3.REMOVE THE GRILL ASSEMBLY UNDERNEATH THE PIECE IN STEP 2 BY PUSHING DOWN FIRMLY ON 4 RETAINER CLIPS WHICH RUN ALONG THE TOP. USE A WIDE SLOT SCREWDRIVER. PULL UP GENTLY ON GRILL ASSEMBLY. IT WILL POP OUT. THE GRILL ASSEMBLY EXTENDS UNDER EACH HEADLIGHT ASSEMBLY (HA) AND IT DISPLAYS THE CHEVROLET LOGO IN THE MIDDLE. MY GRILL ASSEMBLY POPPED OUT EASILY AND ALL THE OTHER RETAINER CLIPS ON THE BOTTOM AND BENEATH AND TO THE SIDE OF HA WERE AUTOMATICALLY RELEASED WITHOUT ANY FUSS;
4.ON TOP OF HA SEE ONE TAB (ABOUT 1" LONG)ON THE RIGHT SIDE AND ONE ON THE LEFT (THE ONE ON L IS CLOSER TO THE FENDER);
5.PULLUPWARDDIRECTION ON TABS. THEY WILL SLIDE UPWARD A COUPLE OF INCHES AND WILL RELEASE THE HA WHICH YOU CAN THEN PULL OUT TOWARDS YOU;
6.AT BACK OF THE HA, REMOVE 2 ROUND RUBBER CAPS (ABOUT 4" IN DIAMETER)--ONE FOR LOW BEAM--ONE FOR HIGH. REVEAL BULBS. UNSNAP THE WIRE HARNESS FROM BULB BASE AND TURN BULB 1/4 TURN CLOCKWISE (REMEMBER YOU ARE FACING THE TRUCK)
7.REPLACE BULB(S). #9006 BULB IS GRAY-BASE, FOR HIGH BEAM ON OUTSIDE. #9005 IS BLACK-BASE, LOW BEAM TO INSIDE OF HIGH BEAM.
CHANGING HIGH AND LOW AND REASSEMBLY TOOK ABOUT HALF HOUR. GOOD LUCK. ALTERNATIVE: IF YOU ARE REPLACING THE PASSENGERSIDE HEADLIGHT JUST REMOVE THE AIR FILTER COVER AND PULL PLUG OUR FROM BEHIND HEADLIGHT AND REPLACE. BE CAREFUL HANDLING LIGHT BULB. TO CHANGE THE ONE ON THE DRIVER'S SIDE JUST REACH IN FRONT OF THE BATTERY TO ACCESS THE PLUG AND HEADLILGHT. TOOK ABOUT 5 MINUTES. ENJOY YOU TRAILBLAZER, GREAT TRUCK.
Posted on Feb 21, 2010
Tips for a great answer:
Feb 17, 2017 | 2004 Chevrolet TrailBlazer
Dec 02, 2016 | 2004 Chevrolet TrailBlazer
May 23, 2016 | Cars & Trucks
Oct 02, 2015 | 2004 Chevrolet TrailBlazer
Mar 16, 2014 | 2004 Chevrolet TrailBlazer
Mar 02, 2011 | 2004 Chevrolet TrailBlazer
Jan 05, 2010 | 2004 Chevrolet TrailBlazer
Dec 27, 2009 | 2004 Chevrolet TrailBlazer
Aug 19, 2009 | 2004 Chevrolet TrailBlazer
53 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: