Is there any way to reset pats system on a Ford F-150 2001 .had to put a new ignition switch in and transponder . But still have flashing theft light I have the original key

The PATS anti-theft system will not let the starter engage an spin the engine around to start the vehicle if the theft deterrent module does not get correct coded value from the pats key. There is a transponder in the head of the key - when put into the lock cylinder a antenna behind the plastic steering column energizes the transponder which makes it send it's unique code to the computers on the vehicle. You have no clue what you're doing . Take it to a qualified repair shop .

You would need a factory scan tool to check for codes in the computers before just replacing parts. Changing the ignition ? lock & key assemble or the electrical part of ignition switch? If key an lock cylinder the key needs to be programmed into the control modules .

Anti-Theft NOTE: If the instrument cluster or the PCM (or both) is installed, the parameters must be reset in both modules or the vehicle will experience a passive anti-theft system (PATS) no-start. For additional information, refer to Passive Anti-Theft System (PATS) Parameter Reset in this section.
PATS consists of the following components:

• Anti-theft indicator (located in the autolamp/sunload sensor)
• Encoded (the key contains a transponder) ignition key
• PATS transceiver
• Instrument cluster
• Powertrain control module (PCM)

PATS uses radio frequency identification technology to deter a drive-away theft. Passive means that it does not require any activity by the user.
The vehicle is equipped with 2 PATS keys. A maximum of 8 PATS keys can be programmed to start the vehicle. If additional PATS keys are desired, refer to Spare Key Programming - Unlimited Key Mode in this section.

That is because the switch must be paired with the ECU. Anti theft has activated. Call your local garage for assistance.

Ford anti theft code 13 incorrect key . Most likely the chip in your key is wore out . After three incorrect trys it goes into lock mode witch takes up to 90 mins to clear

You can't just change parts an expect it to work , software , modules won't let it work . You have to take it to the dealer or have a mobile lock smith fix it , reprogram it ETC...
Anti-Theft -Passive Anti-Theft System (PATS) The passive anti-theft system (PATS) contains the following components:

• theft indicator
• encoded ignition key
• PATS transceiver module
• powertrain control module (PCM)
• standard corporate protocol (SCP) communication network
• Passive Anti-Theft System (PATS) -Diagnostic Trouble Codes (DTC) Index Powertrain Control Module Diagnostic Trouble Code (DTC) Index DTC Description Source Action B1213 Anti-Theft Number of Programmed Keys is Below Minimum PCM GO to Pinpoint Test F . B2431 Transponder Program Failure PCM VERIFY if using correct PATS key, if defective USE new key. B1342 ECU is Defective (EEFROM in PCM not working) PCM INSTALL a new PCM. REFER to Section 303-14 . B2103 Antenna Not Connected PCM GO to Pinpoint Test A . B1600 PATS Ignition Key Transponder Signal is Not Received PCM GO to Pinpoint Test B . B1601 PATS Received Incorrect Key-Code From Ignition Key Transponder PCM GO to Pinpoint Test C . B1602 PATS Received Invalid Format of Key-Code From Ignition Key Transponder PCM GO to Pinpoint Test D . B1681 PATS Transceiver Module Signal is Not Received PCM GO to Pinpoint Test E . - All Other DTCs PCM REFER to Section 419-10 .

theft light should be flashing when system is armed. It should reset itself. If on steady, you have a probelem. Try your other key first. This inof should help you. Report back if you still need help.

Anti-Theft —Passive The passive anti-theft system (PATS) contains the following components:

• theft indicator
• encoded ignition key
• PATS transceiver module
• powertrain control module (PCM)
• standard corporate protocol (SCP) communication network

--------------------------------------------------------------------------------
Principles of Operation
The PATS uses a specially encoded ignition key. Each encoded ignition key contains a permanently installed electronic device called a transponder. Each transponder contains a unique electronic identification code out of over 18 billion, billion combinations.
The passive anti-theft system (PATS), also known as SecuriLock ®, uses radio frequency identification technology to deter a driveaway theft. This system is known as Securilock® in North America, Safeguard® in the U.K., and PATS in Continental Europe. Passive means that it does not require any activity from the user.
The SecuriLock® System (PATS) is not compatible with aftermarket remote start systems, which allow the vehicle to be started from outside the vehicle. These systems may reduce the vehicle security level, and also may cause no-start issues. If equipped the remote start system must be removed before investigation of PATS-related, no-start issues.
Each encoded ignition key must be programmed into the vehicle's powertrain electronic control (PCM) before it can be used to start the engine. There are special diagnostic repair procedures described in this section that must be carried out if a new encoded ignition key is necessary.
This system contains a new feature named Unlimited Key Mode. This feature allows a customer to program more than eight keys to the vehicle if they request it. Each vehicle in Unlimited Key Mode is set up with a special Unlimited Transponder Security Key. This allows all the customer vehicles to share the same keys, but no other keys from outside can be used to operate the vehicles. For an individual customer, any randomly selected Security Key is acceptable. Refer to Unlimited Key Mode Programming in Key Programming Switch State Control in this section.
The PATS transceiver module communicates with the encoded ignition key. The module is located behind the steering column shroud and contains an antenna connected to a small electronics module. During each vehicle start sequence, the transceiver module reads the encoded ignition key identification code and sends data to the PCM.
The control functions are contained in the PCM. This module carries out all of the PATS functions, such as receiving the identification code from the encoded ignition key and controlling the engine enable. The PCM initiates the key interrogation sequence when the vehicle ignition switch is turned to RUN or START.
All elements of the PATS must be functional before the engine is allowed to start. If any of the components are not working correctly, the vehicle will not start.
The PATS uses a visual theft indicator. The indicator will prove out for three seconds when the ignition switch is turned to RUN or START under normal operation. If there is a PATS concern, this indicator will either flash rapidly or glow steadily when the ignition switch is turned to RUN or START. The PATS system also flashes the theft indicator every two seconds at ignition OFF to act as a visual deterrent.
The following will activate the PATS and will disable the vehicle from starting:

• incorrectly encoded ignition key
• damaged encoded ignition key
• unprogrammed key
• non-encoded key (key has no electronics)
• damaged wiring
• damaged transceiver
• damaged PCM

Inspection and Verification

1. Verify the customer concern by operating the system.

1. Visually inspect for obvious signs of mechanical and electrical damage.

Visual Inspection Chart Mechanical Electrical

• Large metallic objects, a second ignition key on the same key ring as the PATS ignition key or electronic devices on the key chain that can be use to purchase gasoline or similar items
• Ignition lock cylinder
• PATS key
• Use of a non-PATS key
• More than one PATS key on key chain

• Central junction box (CJB) fuse 16 (15A)
• Battery junction box (BJB) fuse 20 (15A)
• PATS transceiver module
• Ignition switch
• Loose or corroded connection(s)

the anti-theft light is supposed to blink when the car is locked to show the system is armed.

Does it flash while driving?

Principles of Operation
The PATS uses a specially encoded ignition key. Each encoded ignition key contains a permanently installed electronic device called a transponder. Each transponder contains a unique electronic identification code out of over 18 billion, billion combinations.
The passive anti-theft system (PATS), also known as SecuriLock ®, uses radio frequency identification technology to deter a driveaway theft. This system is known as Securilock® in North America, Safeguard® in the U.K., and PATS in Continental Europe. Passive means that it does not require any activity from the user.
The SecuriLock® System (PATS) is not compatible with aftermarket remote start systems, which allow the vehicle to be started from outside the vehicle. These systems may reduce the vehicle security level, and also may cause no-start issues. If equipped the remote start system must be removed before investigation of PATS-related, no-start issues.
Each encoded ignition key must be programmed into the vehicle's powertrain electronic control (PCM) before it can be used to start the engine. There are special diagnostic repair procedures described in this section that must be carried out if a new encoded ignition key is necessary.
This system contains a new feature named Unlimited Key Mode. This feature allows a customer to program more than eight keys to the vehicle if they request it. Each vehicle in Unlimited Key Mode is set up with a special Unlimited Transponder Security Key. This allows all the customer vehicles to share the same keys, but no other keys from outside can be used to operate the vehicles. For an individual customer, any randomly selected Security Key is acceptable. Refer to Unlimited Key Mode Programming in Key Programming Switch State Control in this section.
The PATS transceiver module communicates with the encoded ignition key. The module is located behind the steering column shroud and contains an antenna connected to a small electronics module. During each vehicle start sequence, the transceiver module reads the encoded ignition key identification code and sends data to the PCM.
The control functions are contained in the PCM. This module carries out all of the PATS functions, such as receiving the identification code from the encoded ignition key and controlling the engine enable. The PCM initiates the key interrogation sequence when the vehicle ignition switch is turned to RUN or START.
All elements of the PATS must be functional before the engine is allowed to start. If any of the components are not working correctly, the vehicle will not start.
The PATS uses a visual theft indicator. The indicator will prove out for three seconds when the ignition switch is turned to RUN or START under normal operation. If there is a PATS concern, this indicator will either flash rapidly or glow steadily when the ignition switch is turned to RUN or START. The PATS system also flashes the theft indicator every two seconds at ignition OFF to act as a visual deterrent.
The following will activate the PATS and will disable the vehicle from starting:

• incorrectly encoded ignition key
• damaged encoded ignition key
• unprogrammed key
• non-encoded key (key has no electronics)
• damaged wiring
• damaged transceiver
• damaged PCM

the security system resets itself after about 15 minutes. If it was the security system, the car would not crank over. Why do you think it's the security system?
do you have gas in tank?

Is it a Ford security system, with the flashing light on the dash?


Principles of Operation
The PATS uses a specially encoded ignition key, this key is not compatible with previous vehicles or any current model year vehicles. Each specially encoded ignition key contains a permanently installed electronic device called a transponder. Each transponder contains a unique encrypted identification code out of over 18 billion, billion combinations.
Each encoded ignition key must be programmed into the vehicle's powertrain control module (PCM) before it can be used to start the engine. There are special diagnostic repair procedures outlined in this manual that must be carried out if a new encoded ignition key is necessary.
This system contains a new feature named Unlimited Key Mode. This feature allows a customer to program more than eight keys to their vehicle if they request it. Each vehicle in Unlimited Key Mode is set up with a special Unlimited Transponder Security Key. This allows all the customer vehicles to share the same keys, but no other keys from outside can be used to operate the vehicles. For an individual customer, any randomly selected Security Key is acceptable. Refer to Key Programming—Unlimited Key Mode in this section.
The PATS transceiver module communicates with the encoded ignition key. The module is located behind the steering wheel column shroud and contains an antenna connected to a small electronics module. During each vehicle start sequence, the transceiver module reads the encoded ignition key identification code and sends data to the PCM.
The control functions are contained in the PCM. This module carries out all of the PATS functions, such as receiving the identification code from the encoded ignition key and controlling the engine enable. The PCM initiates the key interrogation sequence when the vehicle ignition switch is turned to RUN or START.
All elements of the PATS must be functional before the engine is allowed to start. If any of the components are not working correctly, the vehicle will not start.
The PATS uses a visual theft indicator. The indicator will prove out for three seconds when the ignition switch is turned to RUN or START under normal operation. If there is a PATS problem, this indicator will either flash rapidly or glow steadily when the ignition switch is turned to RUN or START. The PATS system also flashes the theft indicator every two seconds at ignition OFF to act as a visual deterrent.
The PATS will be activated and will disable the vehicle from starting if there is a:

• improper encoded ignition key (example — Taurus/Sable key).
• damaged encoded ignition key.
• unprogrammed key.
• non-encoded key (key has no electronics).
• damaged wiring.
• damaged transceiver.

it resets itself.

Principles of Operation
The PATS uses a specially encoded ignition key. Each encoded ignition key contains a permanently installed electronic device called a transponder. Each transponder contains a unique electronic identification code out of over 18 billion, billion combinations.
The passive anti-theft system (PATS), also known as SecuriLock ®, uses radio frequency identification technology to deter a drive-away theft. This system is known as SecuriLock® in North America, Safeguard® in the U.K., and PATS in Continental Europe. Passive means that it does not require any activity from the user.
The SecuriLock® System (PATS) is not compatible with aftermarket remote start systems, which allow the vehicle to be started from outside the vehicle. These systems may reduce the vehicle security level, and also may cause no-start issues. If equipped the remote start system must be removed before investigation of PATS-related, no-start issues.
Each encoded ignition key must be programmed into the vehicle's powertrain control (PCM) before it can be used to start the engine. There are special diagnostic repair procedures described in this section that must be carried out if a new encoded ignition key is necessary.
This system contains a new feature named Unlimited Key Mode. This feature allows a customer to program more than eight keys to the vehicle if they request it. Each vehicle in Unlimited Key Mode is set up with a special Unlimited Transponder Security Key. This allows all the customer vehicles to share the same keys, but no other keys from outside can be used to operate the vehicles. For an individual customer, any randomly selected Security Key is acceptable. Refer to Unlimited Key Mode Programming in Key Programming Switch State Control in this section.
The PATS transceiver module communicates with the encoded ignition key. The module is located behind the steering column shroud and contains an antenna connected to a small electronics module. During each vehicle start sequence, the transceiver module reads the encoded ignition key identification code and sends data to the PCM.
The control functions are contained in the PCM. This module carries out all of the PATS functions, such as receiving the identification code from the encoded ignition key and controlling the engine enable. The PCM initiates the key interrogation sequence when the vehicle ignition switch is turned to RUN or START.
All elements of the PATS must be functional before the engine is allowed to start. If any of the components are not working correctly, the vehicle will not start.
The PATS uses a visual theft indicator. The indicator will prove out for three seconds when the ignition switch is turned to RUN or START under normal operation. If there is a PATS concern, this indicator will either flash rapidly or glow steadily when the ignition switch is turned to RUN or START. The PATS system also flashes the theft indicator every two seconds at ignition OFF to act as a visual deterrent.
The PATS will be activated and will disable the vehicle from starting if there is a:

• incorrectly encoded ignition key
• damaged encoded ignition key
• unprogrammed key
• non-encoded key (key has no electronics)
• damaged wiring
• damaged transceiver
• damaged PCM

Try your spare key first. also, does the anti theft visual indicator (red flashing light) prove out, that is light for three seconds when key is turned to on.

here's some info.

Principles of Operation
The passive anti-theft system (PATS) uses a specially encoded ignition key. Each encoded ignition key contains a permanently installed electronic device called a transponder. Each transponder contains a unique electronic identification code out of over 18 billion, billion combinations.
The passive anti-theft system (PATS), also known as SecuriLock ®, uses radio frequency identification technology to deter a drive-away theft. This system is known as SecuriLock® in North America, Safeguard® in the U.K., and PATS in continental Europe. Passive means that it does not require any activity from the user.
The SecuriLock® System (PATS) is not compatible with NON-FORD remote start systems, which allow the vehicle to be started from outside the vehicle. These systems may reduce the vehicle security level, and also may cause no-start issues. If equipped, the remote start system must be removed before investigation of PATS-related, no-start issues.
Each encoded ignition key must be programmed into the vehicle's powertrain control module (PCM) before it can be used to start the engine. The correct ignition key is a different design than prior model years. Consult the Rotunda Key Ordering Guide for the correct part number. There are special diagnostic repair procedures described in this section that must be carried out if a new encoded ignition key is necessary.
This system contains a new feature named Unlimited Key Mode. This feature allows a customer to program more than eight keys to the vehicle if they request it. Each vehicle in Unlimited Key Mode is set up with a special unlimited transponder security key. This allows all the customer vehicles to share the same keys, but no other keys from outside can be used to operate the vehicles. For an individual customer, any randomly selected security key is acceptable. Refer to Unlimited Key Mode Programming in Key Programming Switch State Control in this section.
The PATS transceiver module communicates with the encoded ignition key. The module is located behind the steering column shroud and contains an antenna connected to a small electronics module. During each vehicle start sequence, the transceiver module reads the encoded ignition key identification code and sends data to the PCM.
The control functions are contained in the PCM. This module carries out all of the PATS functions, such as receiving the identification code from the encoded ignition key and controlling the engine enable. The PCM initiates the key interrogation sequence when the vehicle ignition switch is turned to RUN or START.
All elements of the PATS must be functional before the engine is allowed to start. If any of the components are not working correctly, the vehicle will not start.
PATS uses a visual theft indicator. The indicator will prove out for three seconds when the ignition switch is turned to RUN or START under normal operation. If there is a PATS concern, this indicator will either flash rapidly or glow steadily when the ignition switch is turned to RUN or START. The PATS system also flashes the theft indicator every two seconds at ignition OFF to act as a visual deterrent.
PATS will be activated and will disable the vehicle from starting if there is:

• an incorrectly encoded ignition key.
• a damaged encoded ignition key.
• an unprogrammed key
• a non-encoded key (key has no electronics).
• damaged wiring.
• a damaged transceiver.
• a damaged PCM.

1999 cougar. before they tell me I need a fuel pump I want to be SURE the anti theft system has not shut off the fuel to the engine.
how do I confirm that?