At Fixya.com, our trusted experts are meticulously vetted and possess extensive experience in their respective fields. Backed by a community of knowledgeable professionals, our platform ensures that the solutions provided are thoroughly researched and validated.
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
repairpal.com > ... > P0131 and P0137 - OBD-II Trouble Codes Definition of error code P0131 and P0137 - 02 Sensor Low Voltage (Bank I ... Decrease in fuel Eeconomy because PCM is in a "limp home" mode; Engine dies .... The AAmco company replaced 2 oxygen sensors in my car and the engine light ...
P0031 and P0051 02 heater control, P0131, P0151 and P0132 02 voltage P0748 pressure control solenoid a electric. Your 02 sensors not problem, problem is electric in nature
Essentially the same as P0136 and P0137, a P0131 code refers to the first oxygen sensor on Bank 1. P0131 means the O2 oxygen sensor's voltage remained low for longer than 2 minutes. This, is interpreted by the ECM as a low voltage condition and sets the MIL. Bank 1 Sensor 1 is located in front of the catalytic converter. Multidiag Access J2534 can help you reset it
Reset error codes by disconnecting battery for 5 minutes. Start fresh. all codes should be clear now. drive and see if any new codes come on. They are the ones you need to address.
We guess DTC P0151... essentially the same as P0136 and P0137 and P0131, a P0151 code refers to the first oxygen sensor on Bank 2 . P0151 means the O2 oxygen sensor's voltage remained low for longer than 2 minutes. This, is interpreted by the ECM as a low voltage condition and sets the MIL. Bank 2 Sensor 1 is located in front of the catalytic converter.
There may be no visible symptoms to the driver, other than the MIL (Check Engine / Service Engine Soon) illumination.
A code P0151 may mean that one or more of the following has happened: Faulty o2 oxygen sensor Short to voltage on O2 signal circuit High resistance or open on O2 signal circuit
Possible Solutions: Replace faulty sensor Repair short, open, or high resistance on o2 signal circuit
HI ghosthunter6 codes P0131&P0137&P0341 indicative of having electrical short . P0131 Front Heated Oxygen Sensor Bank 1 harness is open or shorted . P0137 Rear Heated Oxygen Sensor Bank 1 harness is open or shorted . P0341 Camshaft position sensor harness or connectors (The sensor circuit is open or shorted) . code B1218 horn relay coil circuit short to voltage battery . IT could be cousin problem with other sensors . First replace horn relay and clear E C M codes IF problem and codes P0131&P0137 come back you need o2 sensors .put I don't thank so. YOU MUST REPLACE HORN RELAY .OK
P0131=O2 Sensor Circuit Low Voltage Bank 1 Sensor 1 P0151=O2 Sensor Circuit Low Voltage Bank 2 Sensor 1 Marc, this shows that the oxygen sensor on the left exhaust pipe before converter is bad, And the front oxygen sensor on the right exhaust infront of converter is bad.
check for every posible loose ground arrownd the engine block
i had foud that many times and technicians have very hard time to find it if you see some thing wires atached to the engine block pull gently on it to see if they are open internally
and check also for clean and tie circuits at batterie and starter
p0131 and p0151
×