Headlamp breaker location

FIND THE FUSE BOX THROUGH THE MANUAL.. CHANGE THE FUSE.. BE HAPPY
PLS VOTE

To change the bulbs you need to first remove the 5 plastic pop screws on the front bumper. They're spread out at the top of the bumper right under the hood. Once you get those out, you have to remove the two hex bolts on each headlight. Then it gets tricky. You need to pull the light towards the front of the car until it pops out of the ball-bearing type mount on the fender. Once that pops out, you have to pull the front bumper forward while maneuvering the headlight out towards the front.

As per the manual it says as follows:---

Open the hood.

Hold the headlamp to prevent damage to the headlamp or to the fascia. Remove the bolts from the headlamp assembly. Remove the push-in-retainers across the front fascia. Remove the headlamp assembly. Lift the headlamp upward to release the locating tab from the front edge of the fender.

Disconnect the electrical connector from the headlamp assembly.

Remove the headlamp bulb access cover by rotating the headlamp bulb access cover counterclockwise, if necessary.

Remove the headlamp bulb from the housing by rotating the socket counterclockwise, if necessary.

Disconnect the headlamp bulb electrical connector, if necessary.

Remove the park/turn bulb access cover by rotating the cover counterclockwise, if necessary.

Remove the park/turn bulb from the housing by rotating the socket counterclockwise, if necessary.

Gently pull the park/turn bulb from the socket, if necessary. Install the park/turn bulb into the bulb socket.

Install the park/turn bulb socket into the headlamp housing by rotating the socket clockwise.

Install the park/turn bulb access cover by rotating the cover clockwise.

Connect the headlamp bulb to the headlamp electrical connector.

Install the headlamp bulb into the headlamp housing. Rotate the socket clockwise until locked.

Install the headlamp bulb access cover by rotating the cover clockwise.

Position the headlamp assembly to the vehicle. Lift the headlamp upward to release the locating tab to the front edge of the fender.

Install the bolts to the headlamp assembly. Tighten the bolts to 2 N·m (18 lb in).

Install the push-in-retainers across the front fascia.

Close the hood.

----------This will help.thanks.Helpmech.

Section 17-01: Lighting, Exterior 1995 Town Car, Crown Victoria, Grand Marquis Workshop Manual REMOVAL AND INSTALLATION Headlamp Assembly Removal and Installation

1. WARNING: THE HALOGEN HEADLAMP BULB CONTAINS GAS UNDER PRESSURE. THE HEADLAMP BULB MAY SHATTER IF THE GLASS ENVELOPE IS SCRATCHED OR THE HEADLAMP BULB AND RETAINER (13N021) ARE DROPPED. HANDLE BULB CAREFULLY. GRASP HEADLAMP BULB AND RETAINER ONLY BY ITS PLASTIC BASE. AVOID TOUCHING GLASS ENVELOPE. KEEP HEADLAMP BULB AND RETAINER OUT OF REACH OF CHILDREN.
   NOTE: The headlamp (13008) on this vehicle does not need replacement when the headlamp bulb and retainer burns out. Refer to Headlamp Bulb for removal and installation of headlamp bulb and retainer .
   Position headlamp in the OFF position.

1. Remove headlamp dash panel junction wire (14290) from headlamp bulb and retainers by grasping wires firmly and carefully snapping connector downward.

1. NOTE: Use snap-ring pliers to spread headlamp mounting clips (13N129) , then pull straight upward to disengage.
   Remove three headlamp mounting clips attaching headlamp to radiator grille opening panel reinforcement (8A284) .

1. Remove headlamp from vehicle.

1. To install, reverse Removal procedure.

1. Aim headlamp .
   
   

REMOVAL PROCEDURE

1. Open the hood.
2. Remove the push-pin retainers that secure the top of the upper fascia and grille assembly to the upper tie bar to allow the upper fascia and grille assembly to flex forward.
3. Remove the bolt and the push-pin retainer that secures the top of the headlamp assembly to the upper tie bar.

1. Gently pull the upper fascia and grille assembly forward only far enough to remove the bolt located at the bottom inboard side of the headlamp assembly.
2. Pull the headlamp assembly straight out to disengage the snap-in retainer at the lower outboard back surface of the assembly. Turn the assembly so that the front inboard corner clears the front fascia.
3. Pull the headlamp assembly out and away from the vehicle
4. Disconnect the headlamp electrical connector.
5. Remove the headlamp assembly from the vehicle.
6. Remove the headlamp bulb cover from the headlamp assembly.
7. Remove the headlamp bulb socket from the headlamp assembly.

CAUTION: Refer to Halogen Bulb Caution in Service Precautions.

1. Remove the headlamp bulb.
2. Remove the side marker bulb socket from the outer side of the headlamp assembly.
3. Remove the side marker bulb.
4. Remove the parking lamp bulb socket from the inner edge of the headlamp assembly.
5. Remove the parking lamp bulb.

INSTALLATION PROCEDURE

CAUTION: Refer to Halogen Bulb Caution in Service Precautions.

1. Install the headlamp bulb to the socket.
2. Install the headlamp bulb socket to the headlamp assembly.
3. Install the headlamp bulb cover to the headlamp assembly.
4. Install the side marker bulb to the socket.
5. Install the side marker bulb socket to the headlamp assembly.
6. Install the parking lamp bulb to the socket.
7. Install the parking lamp socket to the headlamp assembly.
8. Connect the headlamp electrical connector.
9. Install the headlamp assembly to the vehicle by placing it back into position so that the bolt holes align and the snap-in retainer located at the outboard back surface of the headlamp assembly engages.
10. Gently pull the upper fascia and grille assembly forward only far enough to install the bolt located at the bottom inboard side of the headlamp assembly.

NOTE: Refer to Fastener Notice in Service Precautions.

1. Install the bolt and push-pin retainer that secures the top of the headlamp assembly to the upper tie bar.

Tighten the bolts to 6 N.m (53 lb in).

1. Install the push-pin retainers that secure the top of the upper fascia and grille assembly to the upper tie bar to allow the upper fascia and grille assembly.
2. Close the hood.

Have you tried to change the headlights?

REMOVAL & INSTALLATION Sealed Beam NOTE: If vehicle is equipped with headlamp doors turn the headlight switch ON. Open the hood and locate the power distribution center. This center is located in the front of the left front strut tower. Remove the cover from the center and remove the Headlamp Close Relay. This will prevent the headlamp doors from closing to provide easier servicing. Turn the headlight switch to OFF, then perform this repair.

1. Remove the headlight bezel.
2. Unhook the spring from the headlight retaining ring if so equipped.
3. Unscrew the retaining ring and remove it. NOTE: Do not disturb the two long aiming screws. Conventional and Halogen headlamp sealed beams units are interchangeable in pairs, but it is recommended that they not be mixed together (one halogen and one conventional). It is fine to upgrade from conventional bulbs to halogen, but do not change from halogen bulbs to conventional bulbs, especially if the vehicle came equipped with halogen bulbs.
   
4. Unplug the old sealed beam from the engine electrical wiring harness.
5. Extract the old bulb from its mounting bracket. To install:
   
6. Connect the replacement bulb and install it into the receptacle (check operation of headlight before completing repair).
7. Install the retaining ring and secure it in place with the retaining screws. Connect the spring.
8. Install the headlight bezel.

Aero Headlamp Aero headlamp systems use replaceable halogen bulbs that are mounted in aerodynamic, molded plastic lens reflector assemblies. NOTE: Lens fogging is a normal condition and does not require service, as moisture will vent from tubes behind the lens on Aero headlamp-type system. EXCEPT PREMIER AND MONACO It may be necessary to remove the entire headlamp assembly if enough access cannot be gained otherwise.

1. Locate and remove the wire connector behind the headlamp assembly in the engine compartment. It may be necessary to remove certain items in the engine compartment to gain access to the bulb wires.
2. Rotate the bulb retaining ring counterclockwise 1?4 turn and remove the ring, bulb and bulb holder from the lens assembly. The bulb holder has alignment notches. NOTE: Do not touch the bulb with bare fingers or any possibly oily surface, since reduced bulb life may result! Fig. 1: To remove the light bulb, first unplug the headlight electrical connector, then . . .
   Fig. 2: . . . remove the light bulb socket retaining ring
   Fig. 3: Rotate the light bulb socket 1?4 turn counter-clockwise, then pull it straight out of the lens assembly
   To install:
   
3. Wearing gloves or holding the replacement bulb with a cloth rag to keep oil off of the bulb surface, insert the bulb into the rear hole of the headlamp assembly. Make certain that the alignment grooves and tabs line up, push the light bulb into the assembly until seated flush, then turn the bulb clockwise 1?4 turn.
4. Plug the electrical light bulb wiring harness into the new light bulb. Install any items removed from the engine compartment.

PREMIER AND MONACO Unlike the other vehicles covered by this manual, the removal and installation of the headlamp bulbs in the Premier and Monaco models requires the extraction of the entire headlamp lens assembly.

1. Remove the grille-to-headlamp assembly attaching screws.
2. Disconnect the headlamp aiming cable from the aiming screw end.
3. Remove the headlamp assembly attaching bolts from above and behind the lamp assembly and separate the lamp assembly from the vehicle.
4. Unplug the headlamp wire connector. NOTE: Do not touch the bulb with bare fingers or any possibly oily surface, since reduced bulb life may result!
   
5. Rotate the socket counterclockwise 1?4 turn and pull the socket from the back of the lens assembly. Fig. 4: Remove the bezel retaining screws to loosen the headlamp assembly - Premier and Monaco
   Fig. 5: Detach the headlamp wire connector - Premier and Monaco
   Fig. 6: Once the headlamp assembly has been removed from the vehicle, the various light bulbs can easily be removed - Premier and Monaco
   To install:
   
6. Wearing gloves or holding the replacement bulb with a cloth rag to keep oil off of the bulb surface, insert the bulb into the rear hole of the headlamp assembly. Make certain that the alignment grooves and tabs line up, push the light bulb into the assembly until seated flush, then turn the bulb clockwise 1?4 turn.
7. Plug the headlamp wire connector back into the headlamp bulb.
8. Install the assembly into the vehicle and secure in place with the mounting bolts.
9. Connect the headlamp aiming cable to the aiming screw end.
10. Install the grille-to-headlamp assembly attaching screws.

1. Check that headlamp switch (11654) is in the off position.
   
2. Lift hood (16612).
   
3. Release latch and swing filler panel to left or right.
   
4. Remove electrical connector from headlamp bulb by grasping wires firmly and snapping connector rearward.
   
5. Remove headlamp bulb retainer (13N019) by rotating counterclockwise (when viewed from rear) about one-eighth turn and sliding ring off plastic base. Keep headlamp bulb retainer as it may be used again to retain new headlamp bulb.
   
6. Carefully remove headlamp bulb from socket by gently pulling straight backward out of socket. Do not rotate headlamp bulb during removal.

Headlamp Assembly, Explorer
Removal and Installation

1. Disconnect battery negative cable.
   
2. Remove blind rivets (2) attaching screws (4) and radiator upper sight shield.
   
3. Remove turn/park lamp attaching screws (2) and pull assembly away from body. Remove bulb sockets from housing and remove lamp assembly. Repeat on opposite side of vehicle.
   
4. With turn/park lamp assembly removed, screw attaching grille to front fender flange is accessible. Remove grille attaching screw. Repeat on opposite side of vehicle.
   
5. Remove attaching screws (4) located across top of grille.
   
6. Grip lower edge of grille and pull outward to disengage from retaining clips. Remove grille.
   
7. Using needle-nose pliers, compress barbs on headlamp housing retainer. With barbs compressed, pull forward on housing just enough to disengage from retainer. Repeat on opposite side of headlamp housing.
   
8. Turn headlamp housing as necessary and pull forward to disengage from headlamp aiming ball socket.
   
9. Disconnect wiring from headlamp bulb socket.
   
10. If replacing headlamp housing, remove retaining collar and bulb.
    

For installation, follow removal procedures in reverse order. Make sure to check headlamp aim.

Answer remove the headlight assembly and the bulbs are located below the Assembly to remove headlamp assembly and access signals: -open the hood
-while pushing rearward on the headlamp,pull up half-way on the (white)plastic retaining clip on the electrical connector - align the square cut-out on the retaining clip with the notch on the headlamp
-pull the headlamp assembly straight out from the vehicle (moving the headlamp up and down slightly may help with its removal)
-locate the front turn signal,parking lamp and foglamp bulbs which are located below the headlamp assembly (turn/parking lamp on top and the fog lamp is below it)
-turn the bulb socket 1/4 turn counterclockwise to remove it from assembly
-pull the old bulb from the socket and replace it with a new one
-turn the bulb socket a 1/4 turn clockwise to reinstall it
-reinstall the headlamp assembly carefully so you dont scratch the paint
-push down on (white)plastic retaining clip on the electrical connector while pushing rearward on the headlamp making sure headlamp is secure.

96 sable, only ino I have. should be similar. Please rate, thanks

1. WARNING: THE REPLACEABLE HALOGEN HEADLAMP BULB CONTAINS GAS UNDER PRESSURE. THE HALOGEN HEADLAMP BULB MAY SHATTER IF THE GLASS ENVELOPE IS SCRATCHED OR THE HALOGEN HEADLAMP BULB IS DROPPED. HANDLE HALOGEN HEADLAMP BULB CAREFULLY. GRASP HALOGEN HEADLAMP BULB ONLY BY ITS PLASTIC BASE. AVOID TOUCHING GLASS ENVELOPE. KEEP HALOGEN HEADLAMP BULB OUT OF REACH OF CHILDREN.
   NOTE: A properly aimed headlamp (13008) assembly normally need not be re-aimed after installation of bulb. A burned out headlamp bulb and retainer (13N021) should not be removed from the headlamp until just before a replacement headlamp bulb and retainer is to be installed. Removal of a headlamp bulb and retainer for an extended period of time may allow contaminants (dust, moisture, smoke) to enter the headlamp and affect the performance of the headlamp. When servicing the headlamp bulb and retainer, energize the headlamp bulb and retainer only while it is contained within the headlamp body.
   
   Make sure headlamp switch (11654) is in OFF position.
   

1. NOTE: On some models the clamps holding the integrated relay control module (IRCM) may need to be unsnapped and the module pulled aside to gain access to the driver side bulb.
   
   Open hood and locate headlamp bulb through hole in upper radiator support assembly.
   

1. Remove headlamp wire connector from headlamp bulb and retainer by pulling the connector and wires in a rearward direction.
   

1. Remove headlamp bulb retainer (13N019) by rotating counterclockwise (when viewed from rear) about one-eighth turn and sliding headlamp bulb retainer off headlamp bulb and retainer. Keep headlamp bulb retainer as it will be used again to retain new headlamp bulb and retainer.
   

1. Carefully remove headlamp bulb and retainer from opening in headlamp bulb (13007) by gently pulling straight out of opening. Do not rotate headlamp bulb and retainer during removal.
   

You half to remove the Headlamp housing to change it. Here is the instructions out of the factory manual.
Tell me if this works for you?
HEADLAMP HOUSING - CONCORDE/LHS/330M Headlamp lens fogging is a normal condition and does not require service unless excessive or continual. Moisture will vent from tubes or vents located on the back of the lamp.
REMOVAL

1. Release hood latch and open hood.
2. Remove large rubber grommet (70 mm x 168 mm) from splash shield to gain access to fascia fasteners Access Rubber Grommet
3. Remove fasteners attaching fascia to the front fender and splash shield, using access hole in splash shield Fastener Locations
4. Remove the push pins attaching the fascia to the upper radiator closure panel Remove Push In Fasteners
5. Remove jackscrews attaching headlamp housing to crossmember and remove the lamp housing to access the lamp(s) Headlamp Jackscrews
6. Roll fascia forward to clear way for headlamp housing removal Roll Fascia Forward
7. Disconnect wire connector from back of lamp socket(s) and/or bulbs.
8. Remove headlamp housing Remove Headlamp Housing

INSTALLATION CAUTION: Do not touch the glass of halogen bulbs with fingers or other possibly oily surface, reduced bulb life will result.

1. Place headlamp housing into position.
2. Connect wire connector to lamp socket(s) and/or bulbs.
3. Verify headlamp and signal lamp operation.
4. Install jackscrews to attach headlamp housing to crossmember.
5. Align fascia to bumper reinforcement and install the top center push pins, to upper radiator closure panel.
6. Align the two fascia studs to the fender vertical attachments, at the same time align the fascia groove on the horizontal flange with the fender drive pin. Push fascia rearward to engage the fasteners.
7. Install nut on fascia stud through the splash shield access hole.
8. Verify headlamp operation and alignment

1. Open the hood.
2. Remove the push-pin retainers that secure the top of the upper fascia and grille assembly to the upper tie bar to allow the upper fascia and grille assembly to flex forward.
3. Remove the bolt and the push-pin retainer that secures the top of the headlamp assembly to the upper tie bar.
1. Gently pull the upper fascia and grille assembly forward only far enough to remove the bolt located at the bottom inboard side of the headlamp assembly.
2. Pull the headlamp assembly straight out to disengage the snap-in retainer at the lower outboard back surface of the assembly. Turn the assembly so that the front inboard corner clears the front fascia.
3. Pull the headlamp assembly out and away from the vehicle
4. Disconnect the headlamp electrical connector.
5. Remove the headlamp assembly from the vehicle.
6. Remove the headlamp bulb cover from the headlamp assembly.
7. Remove the headlamp bulb socket from the headlamp assembly.
8. Remove the headlamp bulb.
9. Remove the side marker bulb socket from the outer side of the headlamp assembly.
10. Remove the side marker bulb.