1994 Jeep Cheerokee Laredo: The remote keyless

Keyless Remote Key Programming Procedure:

1. Insert first programmed key into ignition and turn ignition switch to ON for 5 seconds. ...
2. Turn ignition switch to OFF and remove key.
3. Insert second programmed key into ignition and turn ignition switch to ON. ...
4. Turn ignition switch to OFF and remove key.

More items...

Key Fob Keyless Entry Remote for 2008 Jeep Grand ...

..

If the alarm goes off, it its because it was armed in the first place. You mist disarm it before entering the vehicle. To disarm it push the remote control unlock button or open eithe front door or liftgate using the key in the keylock.

i think not.
its too new to cheat.
did you ask your dealer for help, if not why not?

PLESE DONT EVEN TRY.it aint that simple,the computer tells the engine that you have the right key but as you dont have remote locking anymore it thinks your trying to STEAL it.you NEED to replace the remote fob.(you call it keyless entry)think of it this way if it were that simple why fit an alarm system in the first place....(someone asked if you could take out a fuse to stop the alarm !!!!!.)

1. eugen will not start

There are 2 fuse blocks. The Power Distribution Center is under the hood along the passenger side fender and has fuses and relays in it. The other is on the passenger side of the dash and has fuses and circuit breakers.
....1994 Jeep Grand Cherokee Laredo
...(Fuse Block - Passenger side of Dash)
.....1........5........9........13........17........21........25
.20 A...15 A...20 A...20 A....7.5 A....15 A....30 A
.....2........6.......10.......14........18........22........26
.15 A...15 A...10 A...20 A.... 15 A....15 A....30 A
.....3........7.......11.......15........19........23........27
.20 A...15 A...15 A....3 A......15 A....15 A....10 A
.....4........8.......12.......16........20........24........28
.15 A...15 A...15 A...20 A.....10 A...7.5 A....30 A
1)Trailer Tow Relay
2)Brake Lamps
3)Hazard Lamps
4)Security Lamp
5)Interior Lighting
6)Security Alarm Module
7)Security Alarm Relay, Security Alarm Module, Flash-to-Pass
8)Overhead Console, Keyless Entry, Radio Memory/Clock
Memory/Chime Module, Power Locks, Power Mirrors,
HEVAC and VIC
9)Rear Wiper
10)Radio
11)Cigar Lighter
12)Parking Lamps, Automatic Headlamps
13)Horn Relay
14)Power Lock Relays
15)ABS Module and Relay
16)Turn Signals
17)Heating and Air Conditioning Module
18)Airbag Module
19)Interior Mirror, Auto Headlamps, Overhead Console,
VIC/GDM Module, Heated Rear Window Relay Coil,
Illuminated Entry Relay and Chime Module
20)Heated Rear Window Switch, Overdrive Switch, Speed
Control
21)Security Alarm Module, Lamp Outage Module
22)Airbag Module, Speedometer, Tachometer, Telltales and
Gauges
23)Heated Mirror Feed, Heated Rear Window Switch
24)Instrument Panel Illumination
25)Power Seats
26)Power Windows, Power Sunroof
27)Security Alarm Module and Front Wiper
28)Heated Rear Window Relay

Review this information:
- Self-Programming Sentry PROGRAM
- RKE (Remote Keyless Entry Trasmitter)

Good luck... and remember rate my help!!!

remove the fuse

is the alarm after market ? and is so you need to replace it with another after market one .. now if the alarm is factory ?...you will need a remote control from the dealer and they will reprogram it for you

Hi....
To program the RKE (remote keyless entry) on your jeep g cherokee 94.
Follow this steps.
But maybe you will need to do more than one time.
Because some times require a few intents.

but if you have 1 remote programed all ready. you will program up 4 remotes.
If you don't have any one programed and you can't programed with this steps.
You will need to BUY the RECEIVER that is located on the ROOF CONSOLE.
Because some times come damaged....

Ok. I hope this work for your problem.
Thank you for use fixya.