Brake pad replacement

SOURCE: 2003 Ford E250 Remove/replace front brake pads

You will have to take the wheel off, then try to use a latge screw driver to pry between the old pads and the rotor to push the old pads back some, this will allow you to remove the caliper easier later. Next get a T-45 socket and remove both the top and bottom bolts from the back of the caliper. Tilt the brake caliper at the top or the bottom (it different for both side), and slide it off. Then you can just remove the pads. Be careful to notice that the shims on the caliper slide are different from top to bottom, don't mix them up. Pull the caliper slide pins out and inspect the boot for hole or cracks and the pins for rust, replace if any of these condition exist. Use some brake silicone grease to lube the slide pins and put a little into each boot and put the slide pins back in. Check the rubber boots on the caliper pistions to make sure they are not leaking any fluid or ripped. Use one of the old brake pads and a C-clamp to push both pistons on one caliper back in until they are flush. Check to make sure that no fluid leaked out of the caliper pistons while they were being pushed back in. If you want to do what is call a pad slap only then you can install that pads at this time but that is not recommended. It is recommened that you measure, check and turn the rotors if at all possible or replace them, the wheel seals and check and repack the wheel bearings.

SOURCE: Brake Pad Sensor

On my bmw 325i front pads changed,indicator on dash still on,help!!

SOURCE: replace front brake pad 2003 toyota 4 runner

Diagram is unnecessry.
Pull both front wheels
Work one at a time leaving the other for reference
Find the retention spring ... its a paperclip thickness wire spring... dislodge center retention loop and undo from both ends which engage brake pad retention rods.
Pull the rods out
Pull the old pads out... laying everything on the ground
Use scrap wooden wedges to pry between the rotor and the caliper ...inside and out until the calipers are fully withdrawn. Use the new pads to measure if they are far enough back.
Note... the brake fluid will have dropped in the master cylinder over many months of wear... do not fill it. When the calipers are pushed back they will fill the reservoir again... one wheel at a time.
Be sure to identify the correct pad based on what you took out and what is on the other side (if you screwed up the layout)
Make sure to take the old antisqueek backing plate from the old pad and place it on the new pad. They don't use lubricant on these anymore.
Replace the pads... the retention rods... then the retention spring
Do the other side
Then progressively step on the brake peddle until full tension is felt
Check the master cylinder reservoir... probably needs no additional fluid.
New pads will register in existing ridges in each disc in no time at all.
You should check the discs to see if they need to be replaced during this operation...using some calipers

SOURCE: Replace front brake pads

1. Loosen lugs to wheel with wheel on the ground. Remove AFTER jacking the wheel into the air.
2. 2 bolts hold brake caliper to the suspension. Located on the inboard side of caliper. Usually is a regular hex bolt or an allen head. You may need to persuade them loose at first with a hammer or extra leverage.
3. caliper can be lifted off rotor exposing the pads. Be sure to note how the pads look in place so you can replace the new ones in the correct spot.
4. Depress the caliper piston completely back into cylinder with large channel lock pliers. be careful not to scar in any way.
4. put small amount of lube grease on bolt when reinstalling.
Good luck.. say a prayer and go for it.

SOURCE: 2006 dodge ram 2500 4x4 diesel replace brake pads front and back

Straight forward job. Remove wheels, remove 2 caliper bolts per wheel, check bolts,and bushings for wear/corrosion and lubricate, remove calipers, remove brake pads, push caliper pistons into calipers, replace anti-rattle clips, put new pads in, put caliper and bolts in, put wheels on. Start truck and press brake pedal several times to take up slack and you're done.