Interior dome/map light replacement - 2008 Honda C-RV

You need a replacement door switch.

2007 Honda CRV Door Jamb Switch - from $5.99+ - AutoZone

https://www.autozone.com > ... > Door And Door Parts

Equip cars, trucks & SUVs with 2007 Honda CRV Door Jamb Switch from AutoZone. Get Yours Today! We have the best products at the right price.

Honda CRV Door Jamb Switch - AutoZone

https://www.autozone.com > ... > Door And Door Parts

Order Honda CRV Door Jamb Switch online today. Free Same Day Store Pickup. Check out free battery charging and engine diagnostic testing while you are in ...
US$7.99 · ‎In stock

Genuine Honda CR-V Door Jamb Switch

https://www.hondapartsnow.com > Honda CR-V

Genuine Honda CR-V Door Jamb Switch. Door Jamb Interior Dome Light Switch. Enter your vehicle info to find more parts and verify fitment. Select Vehicle ...

Genuine Honda 35400-S5A-013 Door Switch Assembly

https://www.amazon.ca > Genuine-Honda-35400-S5A-...

Genuine Honda 35400-S5A-013 Door Switch Assembly in Interior Switches. ... Took just 5 minutes to replace my drivers door sensor on my Honda CRV 2009.

..

Interior lights and the power door locks are controlled by a electronic control module . Hooking up a factory or some other type professional scan tool an checking for codes an viewing input data to these control modules would be the first thing to do.
The interior lighting system consists of the following:

• lighting control module (LCM)
• driver door module (DDM)
• instrument panel
• dome/map combination
• courtesy/reading lamps
• orientation light
• door lamps
• footwell lamps
• luggage compartment lamp
• glove compartment lamp
• vanity mirrors
• door ajar switches
• viewing wiring diagrams an checking power and ground circuits for these modules would be the next step if no codes were found . Principles of Operation
  Lighting Control Module This vehicle uses a lighting control module (LCM). The LCM is a microprocessor-based module that controls several vehicle subsystems, responds to electrical input signals from various switches, sensors, and external modules and is located on the LH side of the instrument panel. LCM subsystem functions include:
  
  • headlamps with autolamps
  • turn signal lamps/hazard flasher lamps
  • cornering lamps
  • parking lamps
  • daytime running lamps
  • interior lamps
  • demand lamps
  • battery saver
  The LCM interfaces with the driver door module (DDM) via the standard corporate protocol (SCP) network for the illuminated entry feature.
  The interior lamp is illuminated by pressing the individual interior lamp switch. The interior lamp is also illuminated by door ajar switches located in the door latches, when any door is opened. A theater lighting feature gradually increases or decreases the light intensity when switched by opening or closing a door.
  The dome/map lamp combination are located on each side of the interior lamp. The map lamps are operated independently of the interior lamp by two switches located on the interior lamps.
  The interior lamps are illuminated by holding the panel dim switch in the UP position until the dome lamps turn on. The interior lamp also illuminates when a door is opened and actuates the door ajar warning lamp switch in the door latch.
  The front map lamps are powered by the demand lighting circuit and the interior lighting circuit.
  The rear passenger reading lamps are incorporated into the rear seat assist handle and are located over the rear door openings. These lamps are illuminated through power supplied by the LCM demand lighting circuit.
  Interior lamps (controlled by the LCM) are activated by using the dome lamp switch (instant ON/OFF response) or when a door is ajar. The following lamps illuminate for interior lighting:
  
  • instrument panel interior lamps
  • front map lamps
  • rear reading lamps
  • door lamps
  Demand lighting includes lamps that are illuminated by the customer by directly actuating a switch. The front dome/map lamps are located in the overhead console. Each lamp is controlled by its own switch.
  The following demand lamps are powered by the demand lighting output of the LCM:
  
  • glove compartment lamp
  • vanity mirror lamp
  • luggage compartment lamp
  Each lamp has a dedicated switch that closes to ground to illuminate the lamp.
  The front map lamps are powered by either the demand lighting circuit or the interior lighting circuit, depending upon the position of the switch associated with each lamp. When the customer turns the front map lamp switch ON, the front map lamp is illuminated through power supplied by the LCM demand lighting circuit. If the customer moves the map lamp switch to the OFF position, the power from the LCM demand lighting circuit is interrupted and the lamp is reconnected to the interior lighting circuit.
  The rear reading lamps are powered by either the interior lighting circuit or the demand lighting circuit.
  The luggage compartment lamp is controlled by the trunk ajar switch, and is powered by the demand lighting output from the LCM, and is mounted near the center of the upper rear panel.
  The glove compartment lamp system consists of a glove compartment lamp switch and wire and miniature bulb assembly. Opening the glove compartment door closes the switch which provides power to the glove compartment lamp switch and wire. The glove compartment lamp switch is grounded to the body sheet metal.
  The vanity mirror lamp system consists of a switch and bulb assembly in the RH inside visor and the LH inside visor. Lifting the vanity mirror cover closes the vanity mirror lamp switch and provides power to the lamps.
  The illuminated entry system is controlled by the LCM and provides interior lighting upon entry to the vehicle.
  Interior lamps will be illuminated for 25 (±1) seconds which includes a theater lighting ramp-up time (0.5 seconds). This time interval does not include the theater lighting ramp-down time. Interior lamps will be turned off before the 25 (±1)-second timeout if the ignition switch is turned to the RUN or ACC position.
  The illuminated entry system has the following additions to accommodate the remote entry system: pressing the unlock button on the remote transmitter will activate the illuminated entry system (with theater ramp-up). When the driver door module detects a button press, it sends a signal on the J1850 communication network activating the interior lamps. The lighting control module will turn off the lamps by sensing the all doors lock signal.
  The battery saver feature prevents excessive drain from loads inadvertently left on. When the ignition switch is turned OFF, power is interrupted to the interior lamps and headlamps (after a 10-minute timeout) and the demand lamps (after a 30-minute timeout).
  The battery saver has the following inputs:
  
  • luggage compartment door ajar switch
  • dome lamp switch
  • ignition switch status
  • illuminated entry signal
  • headlamp switch
  • driver/passenger door ajar entry switch
  • keyless entry remote transmitter
  • door unlock, luggage compartment door release

The courtesy lamp supply voltage circuit of the body control module (BCM) supplies battery positive voltage to the dome lamp, the liftgate lamps, and the map lamps. When any door is opened, the door jamb switch contacts close providing a door open input to the BCM. The BCM then provides a ground to the interior lamps with the switch in the AUTO position. The interior lamps receive a ground at G401 with the switch in the ON position.
The following lamps may be manually turned ON by placing the interior lamp switch in the ON position, or by opening a door while the switch is in the AUTO position.
?€¢
The dome lamp

?€¢
The liftgate lamps

?€¢
Courtesy/map lights

You can't turn them on manually ?
This could be a BCM problem , this best left to a ASE certified repair shop or the dealer .

Check the dome light switch. I believe its between the map lights in the front overhead console. You can set it to Always Off, On with Doors, or Always On.

The Dome light and the cargo area light should come on when the door is open and the switch is set to door position, or when set to the always on position.

If only one of the lights come on change the bulb of that light. If neither light comes on change the fuse.

I believe the instrument panel fuse block is located on the passenger side of the center console, to the left of the glove box near the floor. The cover usual lists where and what each fuse does. Look for Interior Lighting, I believe #23. Pull the fuse and check if its broken. If it is replace it. If not you may have electrical issues.

hAVE YOU CHECKED THE FUSE FOR THE INTEROR LIGHTS?

how do u turn interior light of with door open?

I had the same issue with my 2008 w/ moonroof. It's tough but you just have to evenly apply pressure on both sides and pull it straight down. There's two pressure clips that are holding it. I replaced with LEDS, the rear was tough as well!

Is the climate control out also? If so it is fuse 10 (5amp) interior fuse panel.