I have baleeno car 2004 mod. when i AC on petrol rmp a bit high 900 to goes 1000. its fine. but on when AC on CNG rpm goes down 1000 to 800. any one hepl me about this issue. thx
Check and lube the Idle Air Control (IAC) valve,
This tiny electric motor is mount on top valve cover and close to the accelerator cable.
The function of IAC motor is to idle up the RPM when more load is added.
Example: A/C on,light on,stop light on and radio on.
A stuck IAC can be free by few soft tape on the body of the motor.
To lube the worm gear,you will need WD-40 to free up the old grease and lube white lithium grease.
Clean the electrical contacts with CRC electric part cleaner.
This electric motor is very expensive.
Please handle it with care.
Fron day one (1998) the IDC motor is pre-lube with a coat of white lithium grease.
Over the year this coat of grease will dry up and start binding the movement of the worm gear (spiral gear).
The worst case is a burn out motor.
=======
THE FIX
Take off the IAC motor and clean out the old 1998 lithium grease and re-apply fresh grease.
Install the motor.
Check for more rpm increase movement with load change.
Suzuki should stay with NGK stock plug.
Look at the sticker under the hood for the correct spark plug recommendation and the correct gapping on the plugs.
The IAC is an electrical motor (LOOK FOR WIRES and CONNECTOR)
It's on the TOP portion of the valve cover.
Closer to the end of the throttle cable.
It's job is to increase RPM when the engine under load.
Get a friend who is into car and with a little help you will found this small electrical motor.
0.044" or 1.11 mm is the standard gap.
The plug type is PRINTED on a STICKER under the hood or near the left or the right side of the radiator support.
I'm in USA and I do not have access to Suzuki Baleno part cross reference chart.
=========
Leaky injector and/or dry rotted o-ring is the primary cause of spark plug fouling.
=========
I have to stay within the Fixya service term of agreement on answering one question /topic per post.
If you have more RPM related then please reply on the comment link.
Carefully remove the black plastic air inlet tube.
Looking into the throttle plate.
Spray carburetor cleaner into the intake chamber.
Clean and wipe the dirt off the throttle plate.
Let the vapor air out.
install the black plastic tube.
======
Clean / replace air filter.
Tighten the intake manifold and the surrounding bolts /screws.
This will help prevent additional (un-metered) air draw into the combustion chamber.
Additional air will create an above 14.7 (air) to 1 fuel mixture.
=======
I'm in USA and we has Suzuki Swift 1.3L 4 cyc engine.
You engine may be a transplant from a 1995 Baleno. .
I recommend you to repost this and state which country this Baleno home market.
Also has the VIN number of the motor posted so someone can verify/decode the year of this 1.3 liter engine.
×
1,297 views
Usually answered in minutes!
Thank you very much for your messege.
but i can not under stand this :(To lube the worm gear,you will need WD-40 to free up the old grease and lube white lithium grease?
thank you ver much sir
its very clear now
can i ask you another Question about spark plugs ???
Dear Sir,
I caused you inconvenience.but i opened my baleno car and i can not find Idle Air Control
best regards
Many thanks and I really appreciate your soonest response.
Please note that I still have some questions:
1- please tell me what the spark plug ngk model and gab size 11mm or 8mm i can use in baleno 1.3 1998.
cauze no body know and i can not find in web sites what the suitable spark plugs for baleno
2- why the new spark plugs after 2,3 days become Dry and Wet Fouling??
best regards
good morning sir ,
i can not find IAC in my car
please can you see this link?? its contain my engine
http://assets.pakwheels.com/forums/2009/...
best regards
A Plus Forum The Filipino Channel History & Pinoy Tv Schedule
Halik Video 2019
Halik 2019 Full Episode
Pinoy Tv Replay 2019
×