What do I have to remove to access blend door actuator

They are usually behind the centre console and glove box

https://www.google.com/search?q=2006+Chevy+HHR+6%2C+2.4L.+replace+the+blend+door+actuator

..

1. Locate the blend door actuator. The actuator is located behind the dashboard, usually on the passenger side. It is a small, rectangular motor with a wiring harness and a linkage arm.
2. Disconnect the battery. Before beginning any work on the electrical system, disconnect the battery to avoid any electrical shorts or other accidents.
3. Remove the dashboard panel. In order to access the blend door actuator, the dashboard panel may need to be removed. Consult the vehicle's repair manual for specific instructions on how to remove the panel.
4. Remove the old blend door actuator. Disconnect the wiring harness and the linkage arm from the old blend door actuator. Remove any mounting screws or bolts that secure the actuator to the dashboard.
5. Install the new blend door actuator. Install the new blend door actuator in the same location as the old actuator. Secure the actuator with any mounting screws or bolts. Connect the wiring harness and the linkage arm to the new actuator.

Temperature Blend Door Actuator - RH, EATC Removal and Installation

1. Remove the RH floor console finish panel.

1. Lower the glove compartment.

1. Disconnect the RH temperature blend door actuator electrical connector.
2. Remove the 3 RH temperature blend door actuator screws.
1. Remove the RH temperature blend door actuator.

2006 2010 Ford Explorer NO Heat Passenger Temp Actuator Replacement same as mountaineer

The most common cause of this is that you have a stuck air temperature control blend door, this can be a motor actuator issue or a jammed door or both (common). To replace both parts you will need to completely remove the dash from the car to access the blend door.

I'm having the same problem except on mine it's the driver's side that's blowing cold. Do you have the pictures in a finer resolution? I can't make them out and when I zoom, they are too grainy. Does the replacement require removing the dashboard? What's the general cost of the acuators? Are they readily available at like NAPA or other parts stores?

y9ou can gain access to the driver side blend door actuator by removing the glove box. The actuator will be in the left corner of the glove box opening. If you remove the actuator you will be able to turn the pin. If you can turn it 360 degrees the blend door is broke.

If your lucky its only the drivers side. If you get the repair kit from chrysler it will come with instructions with pictures on how to replace the blend door without pulling the HVAC unit/Dash. If the passenger side is broken the HVAC unit will need to be removed.

Heater treater (google them) also have a metal blend door replacement and instructions online on how to replace them without pulling the HVAC housing.

I’m happy to assist further over the phone at https://www.6ya.com/expert/jeremy_d728a59f986299fa

The blend door is not working right or the in car air temperature sensor is faulty.
Removal & Installation Air Inlet Door Vacuum Motor To Remove:

1. Remove the instrument panel.
2. Remove the air inlet door motor mounting screws. CAUTION
   Do not attempt to bend any part of the air inlet duct door lever.
   
3. Rotate and remove the air inlet door vacuum control motor.

To Install:

1. Rotate and install the air inlet door vacuum control motor.
2. Install and tighten the mounting screws.
3. Install the instrument panel.

Defroster Door Vacuum Motor To Remove:

1. Remove the passenger air bag module from the instrument panel.
2. Disconnect the vacuum line and remove the mounting screws. CAUTION
   Do not attempt to bend any part of the defroster airflow mode door lever.
   
3. Rotate and remove the vacuum control motor from the defrost door lever.

To Install:

1. Rotate and install the vacuum control motor on the defrost door lever.
2. Install and tighten the mounting screws.
3. Connect the vacuum line to the vacuum control motor.
4. Install the passenger's air bag module.

Floor Console Register Duct Vacuum Motor To Remove:

1. Remove the floor console.
2. Remove the right-side instrument panel insulator.
3. Working from the passenger's footwell, disconnect the vacuum hose.
4. Remove the screws and the floor console register duct vacuum control motor. CAUTION
   Do not attempt to bend any part of the floor console register duct door lever.
   
5. Rotate and remove the vacuum control motor from the floor console register duct door.

To Install:

1. Rotate and install the vacuum control motor on the floor console register duct door.
2. Install and tighten the mounting screws.
3. Connect the vacuum hose to the floor console register duct vacuum control motor.
4. Install the insulator under the dash.
5. Install the floor console.

Panel/Floor Door Vacuum Motor To Remove:

1. Working through the driver footwell, remove the two screws and the shield. CAUTION
   Do not attempt to bend any part of the airflow mode door lever.
   
2. Label and disconnect the two vacuum hoses.
3. Remove the mounting screw.
4. Lift, rotate and remove the panel/floor door vacuum control motor from the door lever.

To Install:

1. Install the panel/floor door vacuum control motor on the door lever.
2. Install and tighten the mounting screw.
3. Connect the vacuum hoses in their original positions.
4. Install the shield on the vacuum motor.

Auxiliary Air Distribution Blend Door Actuator To Remove:

1. Remove the right rear quarter trim panel access panel. Auxiliary climate control housing removal and installation
   
   
2. Remove the auxiliary air distribution blend door actuator screws.
3. Disconnect the auxiliary air distribution blend door actuator connector.

To Install:

1. Connect the auxiliary air distribution blend door actuator connector.
2. Install the auxiliary air distribution blend door actuator screws.
3. Install the right rear quarter trim panel access panel.

Auxiliary Temperature Blend Door Actuator To Remove:

1. Remove the right rear quarter trim panel. Auxiliary climate control housing removal and installation
   
   
2. Disconnect the temperature auxiliary temperature blend door actuator connector.
3. Remove the temperature auxiliary temperature blend door actuator screws.
4. Remove the temperature auxiliary temperature blend door actuator.

To Install:

1. Install the temperature auxiliary temperature blend door actuator.
2. Install the temperature auxiliary temperature blend door actuator screws.
3. Connect the temperature auxiliary temperature blend door actuator connector.
4. Install the right rear quarter trim panel.

--- In-Car Temperature Sensor Removal & Installation To Remove:

1. Remove the instrument cluster finish panel.
2. Disconnect the in-vehicle temperature sensor connector.
3. Disconnect the in-vehicle temperature sensor aspirator tube.
4. Remove the in-vehicle temperature sensor screws.
5. Remove the in-vehicle temperature sensor.

To Install:

1. Install the in-vehicle temperature sensor.
2. Install the in-vehicle temperature sensor screws.
3. Connect the in-vehicle temperature sensor aspirator tube.
4. Connect the in-vehicle temperature sensor connector.
5. Install the instrument cluster finish panel.

there is a blend door actuator for the laredo and if is bad the air wont come out here is a pic of what it looks like and how to get to it


The single zone heater-A/C system is equipped with a single blend door actuator. The dual zone system has two blend door actuators, one for the driver side blend-air door and one for the passenger side blend-air door.

1. Disconnect and isolate the negative battery cable.
   
2. Remove the glove box from the instrument panel.
3. Remove the three screws that secure the blend door actuator to the passenger side of the HVAC air distribution housing .
4. Remove the blend door actuator from the air distribution housing and disconnect the HVAC wire harness connector from the actuator.
5. Remove the blend door actuator from the vehicle

to instal

1. Position the blend door actuator into the vehicle.
2. Install the blend door actuator onto the passenger side of the HVAC air distribution housing . If necessary, rotate the actuator slightly to align the splines on the actuator output shaft with those on the blend door cam .
3. Install the screws that secure the blend door actuator to the passenger side of the air distribution housing . Tighten the screws to 17 inch lbs. (2 Nm).
4. Connect the HVAC wire harness connector to the blend door actuator.
5. Install the glove box into the instrument panel.
6. Reconnect the negative battery cable.

The control module or actuator is most likely the cause. You can manually set it for cold air until winter. Actuator is under the dash right by the blower.

your actuatior foe the drivers blend door is stuck. try unhooking battery for a few minutes have both on heat and hook back up and start up. the actuators will run thru a learn mode and sometimes this will free up.if not you will need an actuator