Question about 1999 GMC Jimmy
JKS219, with a hot motor, feel the 2 coolant hoses coming out of the firewall. Both should be hot, if not, your heater core has blockage. The fix is, disconnect both hoses from the motor, connect garden hose to cold side and blow out the blockage into a empty cola liter jug. Run water until clear, then switch sides and do it again until runs clear. No cost repair if it's this.
Posted on Sep 19, 2017
Its more than likely the blend door not moving to the heat position. I'm not familiar with the location of the blend door in the 1999 GMC jimmy, since I'm not a mechanic and don't have a manual on that vehicle. If you can get to the blend door housing you might be able to move it physically.
Posted on Sep 13, 2017
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
Here's a link to this great service
Posted on Jan 02, 2017
airjoc does not have a clue to your problem, I take you want to have warmer air not cooler ac. check the control system, if you have a vacum system tou may have a leak, if it is controlled by voltage, check the control panel and the control box. Also open the hood, place the heater on high but not on any defrost setting preferrably on just the floor setting. Start the engine and see if the ac compressor is running. If it is, the control panel is bad.
Posted on Oct 09, 2009
Possibly.. the actuators which operate the doors actually have a position signal for reference, but the actual motors inside the actuators dont realize there is a limit and overshoot their limits causing the fine wires inside to rip apart rendering the actuator scrap but this happens when actuators are still plugged in to the connector while being taken off the heater door, and they can and will still move with the key in the off position if the actuator thinks it not in the proper position..thats how they work anyway.hope you had them unplugged untill the last, then this would'nt happen....hope this explaination helped
Posted on Dec 07, 2009
Flushing the heater core is fairly easy just remove the 2 hoses going to the heater core and use a different hose if you have to and use a garden hose to backflush the blockage out..this may take as much as 5-6 times also check for vacumn lines missing or disconnected or breaks pinched ect... some where in the vicinity of the passenger side under hood by the a/c lines ect. good luck hope this helps
Posted on Dec 07, 2009
SOURCE: 19996 Gmc Jimmy is leaking
There are 2 vents on the tank - one for the EVAP (its pipe goes to the front) and the one for the air venting (its pipe goes to the filler cap).
If by gas you mean vapours then the vent is doing its job - eliminating the excessive pressure in the tank. This pressure is caused by a blocked pipe in the EVAP system - one of the pipes you replaced is badly installed, redo all of them.
If by gas you are referring to liquid fuel then tank is overfilled and when the gasoline is heated it expands, completely fills the tank and escapes thru that vent which should have the pipe attached to it - siphon out some of the fuel and replace the vent then check the pipe leading to the cap.
Posted on Apr 27, 2011
Tips for a great answer:
Sep 12, 2014 | 2000 GMC Jimmy
May 13, 2011 | 1999 GMC Jimmy
Oct 21, 2010 | 2004 GMC Envoy
Aug 08, 2010 | 1999 GMC Jimmy
Oct 15, 2009 | 2002 Mitsubishi Galant
May 28, 2009 | 1999 GMC Jimmy
Jun 23, 2008 | 1999 Chevrolet Blazer
120 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: