At Fixya.com, our trusted experts are meticulously vetted and possess extensive experience in their respective fields. Backed by a community of knowledgeable professionals, our platform ensures that the solutions provided are thoroughly researched and validated.
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
Diagram reference number 1 in the image below: "" Fitment: 2006 SUBARU B9 TRIBECA - 4 door
Application Notes:
Category: Electrical. Charging and Starting
SubCategory: Alternator / Generator and Related Components
Position: General
Part Number: 809221090
This
is a Serpentine Belt that fits the 2006 SUBARU B9 TRIBECA - 4 door
with the EZ30D engine. The Serpentine Belt is designed by SUBARU to be
part of the Electrical. Charging and Starting-Alternator / Generator and
Related Components. The Serpentine Belt has a position on the vehicle
of General. The 2006 SUBARU B9 TRIBECA Serpentine Belt is a factory
made SUBARU OEM part and it comes with a 12 month 12.000 mile warranty
(parts only). Do not be fooled by an aftermarket SUBARU B9 TRIBECA
Serpentine Belt! Buy a factory SUBARU part and receive peace of mind! This factory part has a part number of 809221090. "
Pop the hood of the car and locate the serpentine belt routing diagram. The diagram on the 2003 Chevrolet
Impala is on top of the fan shroud. The diagram will be a picture of
all of the accessory pulleys and how the serpentine belt is routed among
the pulleys. This diagram will give you the exact direction for routing
the new belt onto the pulleys. If you cannot find a serpentine belt
routing diagram, take a notepad and pen and draw out the exact routing
diagram of the old belt across the pulleys.
2
Locate the serpentine belt tensioner. It is located below the alternator
on the left front side of the engine. The tensioner on the 3.4 liter,
3.5 liter and the 3.9 liter engines will require a 3/8 ratchet to
release the belt tensioner. The 3.8 liter engine will require a ratchet
and a 15 mm socket for the belt tensioner. Rotate the belt tensioner
clockwise to loosen and remove the belt from the belt tensioner pulley.
3
Slide the old belt from the belt
tensioner pulley. Remove the belt from the remaining pulleys and pull
the belt from the engine compartment.
4
Route the new belt across the
crankshaft pulley first. The crankshaft pulley is the big pulley on the
bottom of the engine in the center. Then route the serpentine belt
across the remaining pulleys as directed by the serpentine belt routing
diagram. Leave the belt tensioner pulley for last.
5
Rotate the belt tensioner
clockwise again to relieve the tension and slide the new belt across the
top of the belt tensioner pulley. Release the belt tensioner and the
belt will tighten up as the tensioner applies pressure to the belt. Make
sure the new belt is properly seated in all the pulleys.
6
Crank the engine and inspect the belt again to make sure that it stays seated in the pulleys.
1
Check to ensure the Sienna's engine is cold, then make sure
the Sienna is in park, the ignition is in the off position and the key
is removed from the ignition to prevent any possibility of the engine
engaging during the serpentine belt replacement.
2
Open the hood and locate the serpentine belt routing diagram
sticker on the side of the engine casing. Study it for a moment before
removing the existing belt. It is essential the new belt be installed
exactly as the diagram indicates.
3
Find the tensioner pulley, the main pulley that controls the
serpentine belt, and fit a 1/2-inch socket wrench over the
self-tensioner on the outside of the pulley.
4
Pull the wrench to the left to move the pulley forward, which loosens the belt, then remove the belt.
5
Compare the old serpentine belt with the new, replacement
belt for length, width and number of grooves on the belt's underside. Be
certain the replacement belt is the right part.
6
Fit the new belt on to each pulley according to the
serpentine belt routing diagram on the manufacturer's sticker, or
according to the drawing made prior to removing the old belt. Fit the
new belt on to the tensioner pulley last, again applying pressure on the
pulley's self-tensioner with the half-inch socket wrench to loosen the
pulley.
7
Release the pressure on the self tensioner and allow the
tensioner pulley to ease back into place, thereby tightening the new
serpentine belt with the appropriate tension.
Good morning! I am enclosing a serpentine belt routing diagram to aid in the installation of your serpentine belt. There are 4 different engine possibilities but i have enclosed all. The serpentine belt tensioner is released by rotating in a clockwise direction as shown in the diagrams. Engine configuration will determine what tools you need but the installation is relatively easy to do. Have a great day!
×